-
Cisco Systems RE1000 - page 1
Getting Started Linksys RE1000 Wireles s -N Extender ...
-
Cisco Systems RE1000 - page 2
2 Getting Star ted RE1000 Range Ex tender 2 Introduction This Getting Started guide can help you connect the extender to your network and solv e common setup issues . Y ou can find mor e help from our award- winning, 24/7 customer support at Linksys .com/support . C ontents Over view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
-
Cisco Systems RE1000 - page 3
3 Getting Star ted RE1000 Range Ex tender T op Po wer Switch Only featur ed in the European versions of the RE1000. Reset Pr ess and hold this button for about eigh t seconds t o reset the extender to its factor y defaults. Y ou can also restor e the defaults from the Administr ation > F actory Defaults scr een in the extender ’ s bro ...
-
Cisco Systems RE1000 - page 4
4 Getting Star ted RE1000 Range Ex tender 4. Select the net work to use , then click Next . 5. T ype your network’ s password, then click OK . - OR - If your network is hidden (your r outer does not broadcast its name), click My network is hidden , enter y our network ’ s information, then click OK . 6. Click Next . Y our extende ...
-
Cisco Systems RE1000 - page 5
5 Getting Star ted RE1000 Range Ex tender 7. Move the extender to its primary location, then click Next . Y our router tests the wireless connection to your relocated extender and prompts you if it needs further adjustment. TIP Y ou can also connec t the range extender by using Wi-F i Protected Setup. F or more information, see “ Using W i- ...
-
Cisco Systems RE1000 - page 6
6 Getting Star ted RE1000 Range Ex tender How t o open the brow ser-based utility After setting up the ex tender with the setup sof tware (located on the CD), the extender will be r eady for use. If y ou would like to change its advanced settings, use the extender ’ s browser-based utility . If the extender has not been set up yet Using a wir ...
-
Cisco Systems RE1000 - page 7
7 Getting Star ted RE1000 Range Ex tender On a Microsoft W indows 7 or V ista computer: 1. Open Windows Explorer , then click Network . The RE1000 icon appears in the right panel . ( Y ou might be requir ed to change the firewall settings to allow the display of networked computers . Refer to your operating system ’ s help for i ...
-
Cisco Systems RE1000 - page 8
8 Getting Star ted RE1000 Range Ex tender Connecting with the Wi-F i Prot ec ted Setup Button Use this method if y our rout er or ac cess point has a Wi-F i Protected Setup button. 1. Click or press the Wi-F i Protected Setup button on the extender . 2. Click the Wi-F i Protected Setup button on the router’ s Wi-F i Pr otected ...
-
Cisco Systems RE1000 - page 9
9 Getting Star ted RE1000 Range Ex tender Connecting with the Wi-F i Prot ec ted Setup Button Use this method if your client devic e has a Wi-F i Pr otected Setup button. 1. Click or press the Wi-F i Protected Setup button on the client device. 2. Click the Wi-F i Protected Setup button on the ex tender’ s W i-Fi Prot ected Se ...
-
Cisco Systems RE1000 - page 10
10 Getting Star ted RE1000 Range Ex tender How t o use Site Sur v ey The Site Sur vey gives a snapshot of all neighboring access points or r outers within range of the extender . T o open the Site Sur v ey page: 1. Log into the bro wser-based utility (see “How to open the browser-based utility ” on page 6). 2. Click the W ireles ...
-
Cisco Systems RE1000 - page 11
11 Getting Star ted RE1000 Range Ex tender T roubleshooting NOT E Y our range ex tender w orks only on the 2.4 GHz net work. It cannot be used on a 5 GHz network . Y ou cannot get your extender connected Check the position of your router and extender • F or first-time setup, you may need to place the extender closer to the router . After you’ v ...
-
Cisco Systems RE1000 - page 12
12 Getting Star ted RE1000 Range Ex tender 3. Click your own network name, then click Connect . In the example below , the computer was c onnected to another wireless network named JimsRouter . The name of the correct net work, BronzeEagle in this example , is shown selected. 4. I f you ar e pr ompted to enter a network key , type y our passw ...
-
Cisco Systems RE1000 - page 13
13 Getting Star ted RE1000 Range Ex tender Y ou have int ermittent connection problems When you position your range extender , place it in a location where the signal strength can be kept between 60% and 100% for optimum performance. ...
-
Cisco Systems RE1000 - page 14
14 Getting Star ted RE1000 Range Ex tender Specifications Model Name Linksys RE1000 Model Description Wireless-N Extender Model Number RE1000 Standards IEEE 802.11n, 802.11g, 802.11b, 802.3u Ports Fast Ethernet, C7 connector for localized AC cable or clip Buttons Reset, Wi-Fi Protected Setup™ LEDs Backlit Cisco logo, Ethernet (active, traffic) Ca ...
-
Cisco Systems RE1000 - page 15
3425-01532 Cisco, the Cisc o logo, and Linksys ar e trademarks or registered trademarks of Cisco and/or its affilia tes in the United States and other countries . A listing of Cisco ’ s trademarks can be found at www.cisco .com/go/trademarks. All other trademarks mentioned in this document ar e the property of their respective owners. © 2011 Cis ...
Cisco Systems RE1000についてご質問がありますか?
次のフォームを使用してください
見つけた説明書を読んでもCisco Systems RE1000の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがCisco Systems RE1000で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。