-
AT&T 1772 - page 1
T wo-Line Digital Answering System with T ime/Day Stamp 1772 Fold open this paper for information about this pr oduct's installation and operation. Please r ead Part 1 — Important Product Information , included in this package. Part 2 © Copyright 1998 Philips Consumer Communications L.P . All rights r eserved. Printed in Mexico. Issue 1A T& ...
-
AT&T 1772 - page 2
INST ALL THE BA TTERIES Open the battery door on the bottom of the unit by pulling on the tabs. Insert the bat- teries as indicated, then close the door . BASIC CONNECTIONS For one two-line wall jack 1 Plug one end of the phone line cord with clear plugs into the system jack labeled L1 OR L1/L2 . 2 Plug the other end of the cord into the two-line w ...
-
AT&T 1772 - page 3
3 Plug the cord from the L2 jack on the system into the dual outlet adapter . 4 Plug the dual adapter into the Line 2 jack. For two-line phone with two cords and a single jack adapter (r equir es a single jack adapter) 1 Plug the single jack adapter into the dual outlet adapter . 2 Plug the cords from the phone into the single jack adapter . 3 Plug ...
-
AT&T 1772 - page 4
If this answering system does not work properly , try the following suggestions before seeking repair assistance. MESSAGE WINDOW IS BLANK Make sure the power transformer is securely plugged into an electrical outlet not controlled by a wall switch. Use only the power cord supplied with your system. If you need a replacement cord, call 1 800 722-912 ...
-
AT&T 1772 - page 5
ANNOUNCEMENT OPTIONS The Answering System 1772 lets you record up to 4 different announcements — A, B, C, and AO. Each can be presented to callers on either Line 1 or Line 2. Y ou can assign the same announcement to be presented on both lines, or you can choose different announcements for each line. NOTE: A total of about 24 minutes of r ecor din ...
-
AT&T 1772 - page 6
VOLUME CLOCK MEMO 2 WAY ON/OFF L1 L2 MIC PLAY LINE 1 LINE 2 REPEAT STOP FORWARD DELETE ANSWERING SYSTEM OPERA TION FORWARD/SKIP MESSA GES T o skip to the next message, press F . T o skip part of a message (cue), hold down F for a few seconds, then release it to resume playing. (The system beeps while F is held down.) T o stop playing messages, pres ...
-
AT&T 1772 - page 7
PLA Y MESSAGES T o play all messages on both lines, wait 4 seconds, or press 7 . T o play all messages on Line 1, press 17 . T o play all messages on Line 2, press 27 . T o play only new messages on both lines, press 6 . T o play only new messages on Line 1, press 16 . T o play only new messages on Line 2, press 26 . SA VE MESSAGES The system autom ...
-
AT&T 1772 - page 8
MEMORY FULL/NO ANNOUNCEMENT If the system answers after 10 rings, and presents 2 beeps but no announcement, the system might be of f for one or both lines, memory might be full, or the system is set to AO and your announcement was lost. T o reset the system to answer and r ecord 1 Enter your Remote Access Code after the 2 beeps. 2 Listen to any rec ...
-
AT&T 1772 - page 9
ANSWERING SYSTEM 1772 1 Dial telephone number and wait for system to answer . 2 Enter Remote Access Code. 3 Listen for messages — OR — Enter touch tone command. 4 Hang up to save messages. Y our Remote Access Code _______ ANSWERING SYSTEM 1772 1 Dial telephone number and wait for system to answer . 2 Enter Remote Access Code. 3 Listen for messa ...
-
AT&T 1772 - page 10
Play messages 7 , 17 , or 27 Play only new messages 6 , 16 , or 26 Repeat message 2 Skip message 5 Delete selected message 3 Delete all messages 03 , 13 , or 23 Record announcement 14* or 24* Record memo 1 * or 2* End a recording # T urn system on 00 , 10 , 20 T urn system off 88 , 188 or 288 OPTION PRESS Play messages 7 , 17 , or 27 Play only new ...
AT&T 1772についてご質問がありますか?
次のフォームを使用してください
見つけた説明書を読んでもAT&T 1772の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがAT&T 1772で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。