Ironclad Automobileの取扱説明書

11ページ 0.41 mb
ダウンロード

ページに移動 of 11

Summary
  • Ironclad Automobile - page 1

    INSTRUCTIONS FOR INST ALLA TION, OPERA TION, AND MAINTENANCE OF LEAD-ACID BA TTERIES IN MOTIVE POWER SER VICE Section 28.00 I nstructions for Installation, Operation, and Maintenance of Lead-Acid Batteries in M otive Power Service T ABLE OF CONTENTS SECTION SAFETY PRECAUTIONS 1 SPILLS AND RECYCLING 2 INTRODUCTION 3 FUNDAMENT ALS OF A STORAGE BA TTE ...

  • Ironclad Automobile - page 2

    3. Be especially careful when working on battery terminal connections. Do not connect any two or more t erminals together unless the connection is a proper a nd correct electrical one. d . When lifting the battery , observe the following precautions: 1. Unless completely insulated lifting beams are available, temporarily cover the exposed metal com ...

  • Ironclad Automobile - page 3

    what you know about a battery’s volts, amps, and ampere-hours, you’re ready to easily change those numbers into the final key concept, watts. W att, W. : Using battery voltage or amperage alone doesn’t tell you e nough about the battery . Multiplying those two values together does. The answer you get is a battery’ s wattage: the electrical ...

  • Ironclad Automobile - page 4

    4. Give the battery an equalizing charge but keep resetting t he charger to the equalize position until the specific gravities remain constant for a period of three hours. At no time should b attery temperature be allowed to exceed 1 10°F (43°C). 5 . At the completion of the charge, the specific gravities of all cells corrected to 77°F (25°C) s ...

  • Ironclad Automobile - page 5

    I n sub-freezing temperatures, water should be added j ust before charging is completed to insure prompt mixing with the electrolyte. Otherwise it may freeze on the surface before mixing. No permanent harm results from low temperature operation as long as freezing is avoided. b . High temperatures have an adverse effect and all practical means shou ...

  • Ironclad Automobile - page 6

    14. CHARGING CHARACTERISTICS a. Only EnerSys approved charging methods should be u sed. T o maximize life, charging should not result in excessive gassing during the initial stages of charge. In addition, the charging method should keep end-of-charge t emperature below 1 10˚F . b. Every effort should be made to ensure that the battery r eceives th ...

  • Ironclad Automobile - page 7

    16. DETERMINA TION OF CAP ACITY a. A battery's capacity will, of course, decrease toward the e nd of its life. Assuming no specific cause of trouble, this will be a gradual decrease and ample warning of limiting capacity will be evidenced by the slowing of the truck or other vehicle toward the end of the day's work. b. A battery is usuall ...

  • Ironclad Automobile - page 8

    e. Another convenient way to ensure proper fill levels is the use of a single point watering (SPW) system. The EnerSys Battery Irrigation System or EZ Fill System are effecient methods of watering a battery . These reliable quality systems allow the operator to fill to the proper level each and every time. f . W ater should only be added to the bat ...

  • Ironclad Automobile - page 9

    i . EnerSys Pro-Meter #94870. This shirt pocket sized meter is versatile for 13 ranges in AC, DC and OHM readings. I t has an audible continuity signal and is accurate to 0.75%. Ideal for the person who wants to do basic battery o r charger troubleshooting. j. EnerSys Battery Lifting Beam. Adjusts to fit batteries from 28" T O 43" long. N ...

  • Ironclad Automobile - page 10

    S ERVICE T OOLS 0 *1. CELL LIFTER - Belt type cat. #SS-5746 *0 2. CROSS LINK PUDDLING DAM - cat. #SS-5749 *0 3. CABLE LUG PUDDLING DAM - cat. #SS-5747 0 *4. CONNECTOR PUDDLING DAM - cat. #SS-5745 (2 hole) *0 5. CONNECTOR PUDDLING DAM - cat. #SS-5745-1 (4 hole) *0 6. CONNECTOR PUDDLING DAM - cat. #SS-5745-2 (4 hole) *0 7. CONNECT OR PUDDLING DAM - c ...

  • Ironclad Automobile - page 11

    ™ Section 28.00 Rev . H 1 1/06 © 2006 EnerSys All Rights Reserved. T rademarks are the property of EnerSys and its affiliates unless otherwise noted. Grafika 2366 Bernville Road, Reading, P A 19605 1-800-EnerSys www .enersysmp.com mpe@enersys.com ISO 9000 ™ ...

メーカー Ironclad カテゴリー Automobile Parts

Ironclad Automobileのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- Automobileの取扱説明書
- Ironcladの製品カード
- パンフレット
- またはIronclad Automobileの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Ironclad Automobileの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Ironclad Automobileの取り付け説明書、サービスマニュアル、簡易説明書、またはIronclad Automobileのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Ironclad Automobileの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Ironclad Automobileデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがIronclad Automobileを使用するのを助ける技術的文書のことです。説明書は通常、全てのIronclad Automobileユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Ironcladの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Ironclad Automobileの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははIronclad Automobileの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Ironclad Automobileに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Ironclad Automobileデバイスの基本機能を使うにあたってのヒント。 Ironclad Automobileのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Ironclad Automobileに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるIronclad Automobileのメーカー/サービスへの連絡先に関する情報。

Ironclad Automobileについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもIronclad Automobileの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがIronclad Automobileで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)