Dell W07Bの取扱説明書

63ページ 8.47 mb
ダウンロード

ページに移動 of 63

Summary
  • Dell W07B - page 1

    Dell OptiPlex 3011 AIO Owner's Manual Regulatory Model: W07B Regulatory Type: W07B001 ...

  • Dell W07B - page 2

    Notes, Cautions, and Warnings NOTE: A NOTE indicates important information that helps you make better use of your computer. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. © 2013 Dell Inc ...

  • Dell W07B - page 3

    Contents 1 Working on Your Computer....................................................................................................... 5 Before Working Inside Your Computer ..................................................................................................................... 5 Recommended Tools ................................... ...

  • Dell W07B - page 4

    Removing the Power Switch ...................................................................................................................................23 Installing the Power Switch .................................................................................................................................... 24 Removing the Hard Drive .. ...

  • Dell W07B - page 5

    1 Working on Your Computer Before Working Inside Your Computer Use the following safety guidelines to help protect your computer from potential damage and to help to ensure your personal safety. Unless otherwise noted, each procedure included in this document assumes that the following conditions exist: • You have read the safety information that ...

  • Dell W07B - page 6

    CAUTION: Before touching anything inside your computer, ground yourself by touching an unpainted metal surface, such as the metal at the back of the computer. While you work, periodically touch an unpainted metal surface to dissipate static electricity, which could harm internal components. Recommended Tools The procedures in this document may requ ...

  • Dell W07B - page 7

    After Working Inside Your Computer After you complete any replacement procedure, ensure you connect any external devices, cards, and cables before turning on your computer. 1. Replace the cover. CAUTION: To connect a network cable, first plug the cable into the network device and then plug it into the computer. 2. Connect any telephone or network c ...

  • Dell W07B - page 8

    8 ...

  • Dell W07B - page 9

    2 Removing and Installing Components This section provides detailed information on how to remove or install the components from your computer. System Overview The following figure displays the inside view of the computer after the back cover has been removed. The call outs show the names and the layout of the components inside the computer. Inside ...

  • Dell W07B - page 10

    6. memory 7. system board 8. coin-cell battery 9. speaker 10. WLAN card slot 11. hard drive 12. communication port 13. power switch 14. chassis Removing the Stand Cover 1. Follow the procedures in Before Working Inside Your Computer . 2. Place the computer on a flat surface, display side facing downwards. 3. Press the tab in to release the stand co ...

  • Dell W07B - page 11

    Installing the VESA Stand 1. Place the VESA stand on the computer. 2. Tighten the screws to secure the VESA stand to the computer. 3. Install: a) stand cover 4. Follow the procedures in After Working Inside Your Computer . Removing the Back Cover 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove: a) stand cover b) VESA sta ...

  • Dell W07B - page 12

    4. Remove the back cover from the computer. 12 ...

  • Dell W07B - page 13

    Installing the Back Cover 1. Place the back cover on the computer. 2. Press at the corners of the back cover to secure it to the computer. 3. Install: a) VESA stand b) stand cover 4. Follow the procedures in After Working Inside Your Computer . Removing the Optical Disk Drive 1. Follow the procedures in Before Working Inside Your Computer . 2. Remo ...

  • Dell W07B - page 14

    4. Remove the screws that secure the bracket to the optical disk drive and remove it from the optical drive. Installing the Optical Disk Drive 1. Place the bracket on the optical disk drive and tighten the screws to secure it. 2. Slide the optical disk drive to the computer and tighten the screw to secure it. 3. Connect the cables to the control bo ...

  • Dell W07B - page 15

    a) stand cover b) VESA stand c) back cover 3. Disconnect the cables from the control board and remove the screws that secure the control board to the computer. Remove the control board from the computer. Installing the Control Board 1. Place the control board on the computer. 2. Tighten the screws to secure the control board to the computer. 3. Con ...

  • Dell W07B - page 16

    Installing the WLAN Card 1. Slide the WLAN card into its slot and tighten the screw to secure it to the system board. 2. Connect the antenna cables to the WLAN card. 3. Install: a) system board cover b) back cover c) VESA stand d) stand cover 4. Follow the procedures in After Working Inside Your Computer . Removing the Memory 1. Follow the procedur ...

  • Dell W07B - page 17

    Installing the Memory 1. Align the notch on the memory-card with the tab in the system-board connector. 2. Press down on the memory module until the release tabs spring back to secure them in place. 3. Place the memory cover back into its place and tighten the screw to secure it. 4. Install: a) back cover b) VESA stand c) stand cover 5. Follow the ...

  • Dell W07B - page 18

    Installing the System Board Cover 1. Place the system board cover on the computer. 2. Tighten the screws to secure the system board cover to the computer. 3. Install: a) back cover b) VESA stand c) stand cover 4. Follow the procedures in After Working Inside Your Computer . Removing the Coin-Cell Battery 1. Follow the procedures in Before Working I ...

  • Dell W07B - page 19

    Installing the Coin-Cell Battery 1. Place the coin-cell battery into its slot on the system board. 2. Press the coin-cell battery downward until the release latch springs back into place and secures it. 3. Install: a) system board cover b) back cover c) VESA stand d) stand cover 4. Follow the procedures in After Working Inside Your Computer . Remov ...

  • Dell W07B - page 20

    Installing the Heat Sink 1. Place the heat sink on the computer. 2. Tighten the screws to secure the heat sink to the computer. 3. Install: a) system board cover b) back cover c) VESA stand d) stand cover 4. Follow the procedures in After Working Inside Your Computer . Removing the System Fan 1. Follow the procedures in Before Working Inside Your C ...

  • Dell W07B - page 21

    4. Follow the procedures in After Working Inside Your Computer . Removing the Processor 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove the: a) stand cover b) VESA stand c) back cover d) system board cover e) heat sink 3. Press the release lever down and then move it outward to release it from the retention hook that sec ...

  • Dell W07B - page 22

    Installing the Intrusion Switch 1. Place the intrusion switch on the computer. 2. Guide the intrusion-switch cables through the tabs on the computer and connect the cable to the system board. 3. Install: a) system fan b) system board cover c) back cover d) VESA stand e) stand cover 4. Follow the procedures in After Working Inside Your Computer . Re ...

  • Dell W07B - page 23

    Installing the Speakers 1. Tighten the screws to secure the speakers to the computer. 2. Guide the speaker cables through the tabs on the computer and connect the cable to the system board. 3. Install: a) system board cover b) back cover c) VESA stand d) stand cover 4. Follow the procedures in After Working Inside Your Computer . Removing the Power ...

  • Dell W07B - page 24

    Installing the Power Switch 1. Place the power switch into its slot on the computer and tighten the screws to secure the it to the computer. 2. Guide the power-switch cable through the tabs on the computer and connect the power-switch cable to the system board. 3. Install: a) system board cover b) back cover c) VESA stand d) stand cover 4. Follow t ...

  • Dell W07B - page 25

    4. Turn and place the hard drive on the hard-drive bracket to access the hard-drive cable. Disconnect the hard-drive cable from the hard drive. 5. Remove the screws that secure the hard-drive bracket to the hard drive and remove the hard drive from the hard- drive bracket. 25 ...

  • Dell W07B - page 26

    Installing the Hard Drive 1. Place the hard drive in the bracket and tighten the screws to secure the hard drive to the bracket. 2. Connect the hard-drive cable to the hard drive and place the hard drive into its slot on the computer. 3. Tighten the screws to secure the hard-drive bracket to the computer. 4. Install: a) back cover b) VESA stand c) ...

  • Dell W07B - page 27

    4. Remove the screws that secure the system board to the chassis of the computer and slide the system board to release it from the chassis. 27 ...

  • Dell W07B - page 28

    5. Lift the system board from one side to remove it from the computer. 28 ...

  • Dell W07B - page 29

    29 ...

  • Dell W07B - page 30

    System Board Components Figure 1. Components Of The System Board 1. serial port connector 2. touchscreen board connector 3. LED board connector 4. SATA connectors 5. intrusion switch connector 6. hard drive/optical drive power connector 7. converter board connector 8. camera connector 9. system fan connector 10. CPU Socket 11. coin-cell battery 12. ...

  • Dell W07B - page 31

    Installing the System Board 1. Place the system board on the computer. 2. Tighten the screws to secure the system board to the base panel. 3. Connect all the cables to the system board. 4. Install: a) optical disk drive b) hard drive c) heat sink d) WLAN card e) memory f) system board cover g) back cover h) VESA stand i) stand cover 5. Follow the p ...

  • Dell W07B - page 32

    4. Remove the screws that secure the display bracket to the computer. NOTE: The number of screws to be removed in touch display is 8 only. 32 ...

  • Dell W07B - page 33

    5. Release the display bracket from its tab on the chassis and remove it from the computer. 33 ...

  • Dell W07B - page 34

    Installing the Display Bracket 1. Place the display bracket on the computer. 2. Tighten the screws to secure the display bracket to the computer. 3. Guide the camera cable and the display cable through their tabs. 4. Install: a) system board b) power switch c) intrusion switch d) system fan e) control board f) optical disk drive g) hard drive h) he ...

  • Dell W07B - page 35

    m) VESA stand n) stand cover 5. Follow the procedures in After Working Inside Your Computer . Removing the Camera 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove: a) stand cover b) VESA stand c) back cover d) system board cover e) WLAN card f) memory g) heat sink h) hard drive i) optical drive j) control board k) system ...

  • Dell W07B - page 36

    c) power switch d) intrusion switch e) system fan f) control board g) optical disk drive h) hard drive i) heat sink j) memory k) WLAN card l) system board cover m) back cover n) VESA stand o) stand cover 4. Follow the procedures in After Working Inside Your Computer . Removing the Serial Port 1. Follow the procedures in Before Working Inside Your C ...

  • Dell W07B - page 37

    Installing the Serial Port 1. Tighten the screws to secure the serial port to the computer. 2. Guide the serial-port cable through its tabs on the computer and connect it to the system board. 3. Install: a) system board cover b) back cover c) VESA stand d) stand cover 4. Follow the procedures in After Working Inside Your Computer . 37 ...

  • Dell W07B - page 38

    38 ...

  • Dell W07B - page 39

    3 System Setup System Setup enables you to manage your computer hardware and specify BIOS ‐ level options. From the System Setup, you can: • Change the NVRAM settings after you add or remove hardware • View the system hardware configuration • Enable or disable integrated devices • Set performance and power management thresholds • Manage ...

  • Dell W07B - page 40

    Keys Navigation <Enter> Allows you to select a value in the selected field (if applicable) or follow the link in the field. Spacebar Expands or collapses a drop ‐ down list, if applicable. <Tab> Moves to the next focus area. NOTE: For the standard graphics browser only. <Esc> Moves to the previous page till you view the main scr ...

  • Dell W07B - page 41

    Option Description • Exit - Exits and starts the computer. Advanced Boot Options The Enable Legacy Option ROMs option will allow the legacy option ROMs to load, when in UEFI boot mode. Without this option, only UEFI option ROMs will load. This option is required for Legacy boot mode. This Legacy boot mode is not allowed when you enable the Secure ...

  • Dell W07B - page 42

    Option Description SMART Reporting This field controls if the hard drive errors for the integrated drives are reported during system startup. This technology is part of the SMART (Self Monitoring Analysis and Reporting Technology) specification. • Enable SMART Reporting - This option is disabled by default. USB Configuration This field configures ...

  • Dell W07B - page 43

    Option Description NOTE: If you delete the admin password, the system password also gets deleted. You can also use the admin password to delete the HDD password. You cannot set an admin password if a system password or an HDD password is already set. You must set the admin password first, if you want to use the admin password with a system password ...

  • Dell W07B - page 44

    Option Description • Activate Chassis Intrusion This field controls the chassis intrusion feature. The options are: • Disable • Enable - This option is enabled by default • On-Silent CPU XD Support Allows you to enable or disable the execute disable mode of the processor. • Enable CPU XD Support - This option is enabled by default. Admin ...

  • Dell W07B - page 45

    Option Description • Delete All Key s- Deletes all the keys NOTE: If you disable the Custom Mode, all the changes made will be erased and the keys will restore to default settings. Table 6. Performance Option Description Multi Core Support Specifies whether the process will have one or all cores enabled. The performance of some applications will ...

  • Dell W07B - page 46

    Option Description NOTE: This feature does not work if you turn off your computer using the switch on a power strip or surge protector or if Auto Power is set to disabled . Deep Sleep Control Allows you to define the controls when Deep Sleep is enabled. • Disabled • Enabled in S5 only • Enabled in S4 and S5 Enabled in S4 and S5 is enabled by ...

  • Dell W07B - page 47

    Option Description Keyboard Errors Specifies whether keyboard related errors are reported when it boots. This option is enabled by default. POST Hotkeys Specifies whether the sign-on screen displays a message, that displays the keystroke sequence required to enter the BIOS Boot Option Menu. • Enable F12 Boot Option menu - This option is enabled b ...

  • Dell W07B - page 48

    Option Description NOTE: This option is relevant only when the Integrated NIC control in the System Configuration group is set to Enable with Cloud Desktop. Server IP Address This option specifies the primary static IP address of the Cloud Desktop Server with which the client software communicates. The default Server IP Address is 255.255.255.255 N ...

  • Dell W07B - page 49

    Updating the BIOS It is recommended to update your BIOS (system setup), on replacing the system board or if an update is available. For laptops, ensure that your computer battery is fully charged and connected to a power outlet 1. Re-start the computer. 2. Go to dell.com/support . 3. Enter the Service Tag or Express Service Code and click Submit . ...

  • Dell W07B - page 50

    NOTE: If the password jumper is disabled, the existing System Password and Setup Password is deleted and you need not provide the system password to log on to the computer. To enter a system setup, press <F2> immediately after a power-on or re-boot. 1. In the System BIOS or System Setup screen, select System Security and press <Enter>. ...

  • Dell W07B - page 51

    4 Diagnostics If you experience a problem with your computer, run the ePSA diagnostics before contacting Dell for technical assistance. The purpose of running diagnostics is to test your computer's hardware without requiring additional equipment or risking data loss. If you are unable to fix the problem yourself, service and support personnel ...

  • Dell W07B - page 52

    52 ...

  • Dell W07B - page 53

    5 Troubleshooting Your Computer You can troubleshoot your computer using indicators like Diagnostic Lights, Beep Codes, and Error Messages during the operation of the computer. Important Information NOTE: Avoid using the touchscreen in dusty, hot, or humid environments. NOTE: Sudden change in temperature may cause condensation on the inner surface ...

  • Dell W07B - page 54

    Blinking Amber Power LED Problem Description 2,6 The processor may be faulty. 2,7 The memory may be faulty. Reseat the memory or install a different memory module. 3,1 The video device or subsystem may be faulty. 3,2 The video subsystem may be faulty. 3,3 No memory module was detected. 3,4 The storage device may be faulty. 3,5 The memory may not be ...

  • Dell W07B - page 55

    Message Description the F1 key to continue, F2 to run the setup utility. No boot device available No bootable partition on the hard drive, a cable or connector is loose, or no bootable device exists. • If the hard drive is your boot device, ensure that the cables are connected and that the drive is installed properly and partitioned as a boot dev ...

  • Dell W07B - page 56

    56 ...

  • Dell W07B - page 57

    6 Technical Specifications NOTE: Offerings may vary by region. For more information regarding the configuration of your computer, click Start (Start icon) → Help and Support , and then select the option to view information about your computer. Table 15. System Information Feature Specification Processor type • Intel Celeron Dual Core • Intel ...

  • Dell W07B - page 58

    Table 18. Audio Feature Specification Controller Intel High Definition Audio with Waves MazzAudio 3 Speaker single 4-ohms speakers in both the left and right speaker assembly (3 W average per channel) Internal microphone support single digital microphone Volume controls Volume up/down buttons, program menus, and keyboard media- control keys Table 1 ...

  • Dell W07B - page 59

    Table 23. Ports and Connectors Feature Specification Audio: • one audio input/microphone port • one headphone port Network adapter one RJ45 connector USB 2.0 four connectors in the back panel USB 3.0 two connectors on the side panel Serial one 9-pin connector; 16550 C compatible Media card reader one 8-in-1 slot Table 24. Power Feature Specific ...

  • Dell W07B - page 60

    Table 26. Stand Feature Specification Tilt –5 degrees to 30 degrees Table 27. Physical Dimensions Feature Specification non-Touch Touch Width 506.80 mm (19.95 inches) 506.80 mm (19.95 inches) Height: Without Stand 323.00 mm (12.72 inches) 323.00 mm (12.72 inches) With Stand 376.95 mm (14.84 inches) 376.95 mm (14.84 inches) Depth 63.20 mm (2.49 in ...

  • Dell W07B - page 61

    Feature Specification Power supply diagnostic light Green light — The power supply is turned on and is functional. The power cable must be connected to the power connector (at the back of the computer) and the electrical outlet. Table 29. Environmental Feature Specification Temperature range: Operating 5 °C to 35 °C (41 °F to 95 °F) Storage ? ...

  • Dell W07B - page 62

    62 ...

  • Dell W07B - page 63

    7 Contacting Dell NOTE: If you do not have an active Internet connection, you can find contact information on your purchase invoice, packing slip, bill, or Dell product catalog. Dell provides several online and telephone-based support and service options. Availability varies by country and product, and some services may not be available in your are ...

メーカー Dell カテゴリー Personal Computer

Dell W07Bのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- W07Bの取扱説明書
- Dellの製品カード
- パンフレット
- またはDell W07Bの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Dell W07Bの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Dell W07Bの取り付け説明書、サービスマニュアル、簡易説明書、またはDell W07Bのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Dell W07Bの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Dell W07Bデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがDell W07Bを使用するのを助ける技術的文書のことです。説明書は通常、全てのDell W07Bユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Dellの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Dell W07Bの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははDell W07Bの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Dell W07Bに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Dell W07Bデバイスの基本機能を使うにあたってのヒント。 Dell W07Bのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Dell W07Bに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるDell W07Bのメーカー/サービスへの連絡先に関する情報。

Dell W07Bについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもDell W07Bの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがDell W07Bで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)