Delta Electronics Series DNM04の取扱説明書

16ページ 0.73 mb
ダウンロード

ページに移動 of 16

Summary
  • Delta Electronics Series DNM04 - page 1

    DATASHEET DS_DNM04SIP10_ 07162008D FEATURES  High efficiency: 96% @ 5.0Vin, 3.3V/10A out  Small size and low profile: (SIP) 50.8x 13.4x 8.5 mm (2.00” x 0. 53” x 0.33”)  Signle-in-line (SIP) pa ckaging  S tandard footprint  V oltage and resistor-based trim  Pre-bias startup  Output voltage tracking  No minimum load requ ...

  • Delta Electronics Series DNM04 - page 2

    DS_DNM04SIP10_071620 08D 2 TECHNICAL SPECIFICA TIONS (T A = 25°C, airfl ow rate = 300 LFM, V in = 2.8Vdc and 5.5V dc, nominal V out u nless otherwise noted.) P ARAMETE R NOTES and CONDITIONS DNM04S0A0R10 Min. T yp. Max. Units ABSOLUTE MAXIMUM RA TINGS Input V oltage (Continuous) 0 5.8 Vdc T racking V oltage Vin,max Vdc Operating T emperature Refer ...

  • Delta Electronics Series DNM04 - page 3

    DS_DNM04SIP10_071620 08D 3 ELECTRICAL CHARACTERISTICS CUR VES Figure 1: Converter efficiency vs. output current (3.3V out) Figure 2: Converter efficiency vs. output current (2.5V out) Figure 3: Converter efficiency vs. output current (1.8V out) Figure 4 : Converter efficiency vs. output current (1.5V out) Figure 5: Converter efficiency vs. output c ...

  • Delta Electronics Series DNM04 - page 4

    DS_DNM04SIP10_071620 08D 4 ELECTRICAL CHARACTERISTICS CUR VES Figure 7: Output ripple & noise at 3.3V in, 2.5V/10A out Figure 8: Outp ut ripple & noise at 3.3Vin, 1.8V/10A out Figure 9: Output ripple & noise at 5Vin, 3.3V/10A out Figure 10: Output ripple & noise at 5Vin, 1.8V/10A out Figure 1 1: T urn on de lay time at 3.3Vin, 2.5V/ ...

  • Delta Electronics Series DNM04 - page 5

    DS_DNM04SIP10_071620 08D 5 ELECTRICAL CHARACTERISTICS CUR VES Figure 13: T urn on delay time at 5Vin, 3.3V/10A out Figure 14: T urn on delay ti me at 5Vin, 1.8V/10A out Figure 15: T urn on delay time at remote turn on 5Vin, 3.3V/16A out Figure 16: T urn on delay time at remote turn on 3.3Vin, 2.5V/16A out Figure 17: T urn on delay time at remote tu ...

  • Delta Electronics Series DNM04 - page 6

    DS_DNM04SIP10_071620 08D 6 ELECTRICAL CHARACTERISTICS CUR VES Figure 19: T ypical transient response to step load change at 2.5A/ μ S from 100% to 50% of Io, max at 5Vin, 3.3V out (Cout = 1uF ceramic, 10 μ F tantalum) Figure 20: T ypical transient response to step load change at 2.5A/ μ S from 50% to 100% of Io, max at 5Vin, 3.3V out (Cout =1uF ...

  • Delta Electronics Series DNM04 - page 7

    DS_DNM04SIP10_071620 08D 7 ELECTRICAL CHARACTERISTICS CUR VES Figure 23: T ypical transient response to step load change at 2.5A/ μ S from 100% to 50% of Io, max at 3.3Vin, 2.5V o ut (Cout =1uF ceramic, 10 μ F t antalum) Figure 24: T ypical transient response to step load change at 2.5A/ μ S from 50% to 100% of Io, max at 3.3Vin, 2.5V o ut (Cout ...

  • Delta Electronics Series DNM04 - page 8

    DS_DNM04SIP10_071620 08D 8 TEST CONFIGURA TIONS V I (+) V I (-) BATTERY 2 100uF Tantalum L TO OSCILLOSCOPE Note: Input reflected-ripple current is measured with a simulated sour ce inductance. Curr ent is measur ed at the input of the module. Figure 29: Input reflected-ripple test setup Vo GND COPPER STRIP 10uF tantalum 1uF ceramic SCOPE Resistive ...

  • Delta Electronics Series DNM04 - page 9

    DS_DNM04SIP10_071620 08D 9 DESIGN CONSIDERA TIONS (CON.) The power module sh ould be conne cted to a low ac-impedance input source. Hig hly inductive source impedances can af fect the st ability of the module. An input capacit ance must be placed close to the modules input pins to filter ripple current and ensure m odule stability in the presence o ...

  • Delta Electronics Series DNM04 - page 10

    DS_DNM04SIP10_071620 08D 10 FEA TURES DESCRIPTIONS (CON.) Over-T emperature Protection The over-temperature protection consists of circuitry that provides protection from thermal damage. If the temperature exceeds the ove r-temperature thre shold the module will shut down. The module will try to restart after shutdown. If the over-temperature condi ...

  • Delta Electronics Series DNM04 - page 11

    DS_DNM04SIP10_071620 08D 11 The output voltage tracking f eature (Figure 40 to Figure 42) is achieved according to the different extern al connections. If the tracking feature is not used, the TRACK pin of the module can be le ft unconnecte d or tied to Vin. For proper voltage tracking, input voltage of the tracking power module must be applied in ...

  • Delta Electronics Series DNM04 - page 12

    DS_DNM04SIP10_071620 08D 12 FEA TURE DESCRIPTIONS (CON.) Sequential St art-up Sequential start-u p (Figure 40) is implemented by placing an On/Off control circuit b etween V o PS1 and the On/Of f pin of PS2. R1 R2 Vo PS1 PS1 Vin On/Off On/Off PS2 Vo PS2 Vin C1 Q1 R3 Simultaneous Simultaneou s tracking (Figure 41) is implemented by using the TRACK p ...

  • Delta Electronics Series DNM04 - page 13

    DS_DNM04SIP10_071620 08D 13 THERMAL CONSIDERA TIONS Thermal management is an importa nt part of the system design. To ensure prop er, reliable operation, suffici ent cooling of the power mod ule is needed over the entire temperature range of the modul e. Convection coolin g is usually the dominant mode of heat transfer. Hence, the choice of equipme ...

  • Delta Electronics Series DNM04 - page 14

    DS_DNM04SIP10_071620 08D 14 THERMAL CURVES Figure 44: T emperature mea surement location * The allowed max imum hot spot temperature is defined at 125 ℃ DNM04S0A0R10( Standard) Output Current vs. Ambient Tem perature and Air Velocity @ Vin = 5V, Vo = 3.3V (Either Orientation) 0 2 4 6 8 10 12 60 65 70 75 80 85 Ambient Temperature ( ℃ ) Output Cu ...

  • Delta Electronics Series DNM04 - page 15

    DS_DNM04SIP10_071620 08D 15 MECHANICAL DRA WING SMD P ACKAGE (OPTIONAL) SIP P ACKAGE ...

  • Delta Electronics Series DNM04 - page 16

    DS_DNM04SIP10_071620 08D 16 P ART NUMBERING SYSTEM DNM 04 S 0A0 R 10 P F D Product Series Input V olt ag e Numbers of Output s Output V olt age Package Ty p e Output Current On/Off logic Option Code DNL - 16A DNM - 10A DNS - 6A 04 - 2.8~5.5V 10 - 8.3~14V S - Single 0A0 - Programmable R - SIP S - SMD 10 - 10A N- negative P- positive F- RoHS 6/6 (Lea ...

メーカー Delta Electronics カテゴリー Power Supply

Delta Electronics Series DNM04のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- Series DNM04の取扱説明書
- Delta Electronicsの製品カード
- パンフレット
- またはDelta Electronics Series DNM04の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Delta Electronics Series DNM04の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Delta Electronics Series DNM04の取り付け説明書、サービスマニュアル、簡易説明書、またはDelta Electronics Series DNM04のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Delta Electronics Series DNM04の製品を使用するにあたって最も人気のある説明書を閲覧できます。

Delta Electronics Series DNM04デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがDelta Electronics Series DNM04を使用するのを助ける技術的文書のことです。説明書は通常、全てのDelta Electronics Series DNM04ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Delta Electronicsの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Delta Electronics Series DNM04の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははDelta Electronics Series DNM04の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Delta Electronics Series DNM04に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Delta Electronics Series DNM04デバイスの基本機能を使うにあたってのヒント。 Delta Electronics Series DNM04のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Delta Electronics Series DNM04に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるDelta Electronics Series DNM04のメーカー/サービスへの連絡先に関する情報。

Delta Electronics Series DNM04についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもDelta Electronics Series DNM04の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがDelta Electronics Series DNM04で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)