Cisco Ethernet Connectors Jackscrewの取扱説明書

10ページ 11.87 mb
ダウンロード

ページに移動 of 10

Summary
  • Cisco Ethernet Connectors Jackscrew - page 1

    Copyright © 1993, Cisco Systems, Inc. 1 All rights reserved. Doc. No. 78-1127-01 Re v . A0 J ac kscrew Installation Instructions (f or EIP P orts) F or Cisco Part Number 51-0385-01 Customer Order Number: DOC-781127= This document provides instructions for replacing the slide-type Ethernet connector locks with jackscre w type connector locks. T ypi ...

  • Cisco Ethernet Connectors Jackscrew - page 2

    2Jackscrew Installation Instructions (for EIP Ports) Obtaining T ec hnical Assistance This document contains instructions for replacing the slide-type connector locks that are standard on Cisco 7000 EIP ports with jackscre ws so that you can connect cables with thumbscre ws to the ports. If you encounter problems that you are unable to resolve, con ...

  • Cisco Ethernet Connectors Jackscrew - page 3

    Jackscrew Installation Instructions (for EIP Ports) 3 F igure 1 Ethernet Connector Locks, Slide-T ype and Jackscrew-T ype The EIP is the 2, 4, or 6-port high-speed Ethernet interface processor for the Cisco 7000 router . The EIP and other interface processors (IPs) slide into slots in the rear of the router chassis (which is sho wn in Figure 2) and ...

  • Cisco Ethernet Connectors Jackscrew - page 4

    4Jackscrew Installation Instructions (for EIP Ports) ■ T ransmit—Lights when frames are being transmitted. When frames are transmitted, the Recei ve LED also lights up because v alid traf fic is being sent on the network. ■ Recei ve—Lights when frames are being recei v ed. It indicates that v alid traf fic is being recei ved from the netw ...

  • Cisco Ethernet Connectors Jackscrew - page 5

    Jackscrew Installation Instructions (for EIP Ports) 5 Requir ed P arts The follo wing parts are included in each jackscre w replacement kit. Because the holes in the EIP are threaded, you need only two lock washers and tw o jackscre ws for each port. Discard the extra flat w ashers and hex nuts included in the kit. ■ 2 jackscre ws ■ 2 lockwash ...

  • Cisco Ethernet Connectors Jackscrew - page 6

    6Jackscrew Installation Instructions (for EIP Ports) Note: For safety , periodically check the resistance value of the antistatic strap. The measurement should be within the range of 1 and 10 Mohms. Installation The follo wing installation process describes the procedure for shutting do wn the interfaces on which you will replace connector locks, r ...

  • Cisco Ethernet Connectors Jackscrew - page 7

    Jackscrew Installation Instructions (for EIP Ports) 7 After you hav e replaced the connector locks, reenable the interfaces by entering the command no shutdown , as sho wn in the follo wing partial e xample. interface ethernet 1/1 no shutdown ^Z Y ou can display the current state of an individual Ethernet interface by entering the command show inte ...

  • Cisco Ethernet Connectors Jackscrew - page 8

    8Jackscrew Installation Instructions (for EIP Ports) Step 4: Repeat steps 2 and 3 for all addition ports that require jackscre ws. Step 5: Place the remov ed brackets and slotted scre ws aside; you can discard them after the jackscre ws are installed, and the installation is complete. Installing the Scr ew-T ype Lock Use the hardware pro vided in t ...

  • Cisco Ethernet Connectors Jackscrew - page 9

    Jackscrew Installation Instructions (for EIP Ports) 9 Chec king the Installation T o check the interfaces, you will connect network interface cables to the EIP ports, reenable any interf aces you shut do wn, if any , then check the LEDs and console displays to verify the status of the interf aces. Step 1: Connect network interface cables to the EIP ...

  • Cisco Ethernet Connectors Jackscrew - page 10

    This document is to be used in conjunction with the Cisco 7000 Har dwar e Installation and Maintenance publication. APPI, ciscoBus, Cisco Systems, CiscoW orks, CxBus, Netscape, The Packet, and SMAR Tnet trademarks, and the Cisco logo is a registered trademark of Cisco Systems, Inc. All other products or services mentioned in this document are the t ...

メーカー Cisco カテゴリー Switch

Cisco Ethernet Connectors Jackscrewのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- Ethernet Connectors Jackscrewの取扱説明書
- Ciscoの製品カード
- パンフレット
- またはCisco Ethernet Connectors Jackscrewの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Cisco Ethernet Connectors Jackscrewの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Cisco Ethernet Connectors Jackscrewの取り付け説明書、サービスマニュアル、簡易説明書、またはCisco Ethernet Connectors Jackscrewのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Cisco Ethernet Connectors Jackscrewの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Cisco Ethernet Connectors Jackscrewデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがCisco Ethernet Connectors Jackscrewを使用するのを助ける技術的文書のことです。説明書は通常、全てのCisco Ethernet Connectors Jackscrewユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Ciscoの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Cisco Ethernet Connectors Jackscrewの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははCisco Ethernet Connectors Jackscrewの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Cisco Ethernet Connectors Jackscrewに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Cisco Ethernet Connectors Jackscrewデバイスの基本機能を使うにあたってのヒント。 Cisco Ethernet Connectors Jackscrewのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Cisco Ethernet Connectors Jackscrewに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるCisco Ethernet Connectors Jackscrewのメーカー/サービスへの連絡先に関する情報。

Cisco Ethernet Connectors Jackscrewについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもCisco Ethernet Connectors Jackscrewの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがCisco Ethernet Connectors Jackscrewで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)