Amana W10233410Aの取扱説明書

28ページ 4.63 mb
ダウンロード

ページに移動 of 28

Summary
  • Amana W10233410A - page 1

    ELECTRONIC ELECTRIC DRYERS Use & Care Guide For questions about featur es, operation/performance , parts, access ories, or service, cal l: 1-800-843-0304 or visit our website at... w ww .amana.com T able of Contents ............ .................... ................. 2 W10233410A ...

  • Amana W10233410A - page 2

    2 T ABLE OF CONT ENTS DRYER SAFETY........... ............................ ................................... .... 2 INSTALLATION INSTRUCTIONS ................................ .................. 4 Tools and Parts .. ................................... ................................... .... 4 Optional Pedestal ........................... ........ ...

  • Amana W10233410A - page 3

    3 ...

  • Amana W10233410A - page 4

    4 INST ALLA TION INSTRUCTIONS T ools and P ar ts G ather the r equired tools and part s befor e starting installation. Read and follow the instructions provided with any tools list ed here. ■ Flat-blade screwdriver ■ #2 Phillips screwdriver ■ Adjustable wre nch that opens to 1" (25.4 mm) or hex-head socket wren ch (for adjusting dryer fe ...

  • Amana W10233410A - page 5

    5 ■ If you ar e using a power supply cor d, a grounde d electrical outlet located within 2 ft (610 mm ) of either side of the dryer . See “Electrical Require ments.” ■ A sturdy floor to support the total dryer weight of 127 lbs (57.6 kg). The combined weight of a companion appliance should also be considered. ■ A level floor with a maximu ...

  • Amana W10233410A - page 6

    6 Installation spacing for ca b inet i nstallation ■ For cabinet installation, with a door , minimum ventilation openings in the top of the cabinet are r equired. 7"* (178 mm) 9"* (229 mm) 7"* (178 mm) 5"** (127 mm) 28" (728 mm) 27" (686 mm) 1"* (25 mm) (25 mm) 1" (25 mm) 1" * Required spacing ** For s ...

  • Amana W10233410A - page 7

    7 If using a power supply cor d : Use a UL listed power supply cord k it marked for use with clothes dryers. The kit should contain: ■ A UL listed 30-amp power supply cor d, rated 120/240 volt mini mum. The cord should be type SRD or SRDT and be at least 4 ft (1.22 m) long. The wires that connect to the dryer must end in ri ng terminals or spade ...

  • Amana W10233410A - page 8

    8 Electrical Connection Power Supply Cor d W ARNIN G Fire Hazar d Use a new UL liste d 30 amp power supply cor d . Use a UL liste d strain relief. Disconnect power b efore making electrical connections. Connect neutral wire (white or center wir e) to center terminal (silver). Groun d wir e (green or b ar e wire) must b e connecte d to green gr oun ...

  • Amana W10233410A - page 9

    9 ■ Put power supply cord thr ough the strain relief. Be sure that the wire insulation on the power supply cor d is inside the strain relief. The strain relie f should have a tight fit with the dryer cabinet and be in a horizontal position. Do not further tighten strain relief scre ws at this point. Style 2: Direct wir e strain relief ■ Unscrew ...

  • Amana W10233410A - page 10

    10 2. Remove neutral ground wire fr om external ground conductor scr ew . Connect neutral gr ound wire and th e neutral wire (white or center w ire) of power supply cor d under center , silver -colored terminal block screw . Tighten screw . A C B D E A. External ground conducto r screw - Dotted line shows position of NEUTRAL ground wire before bein ...

  • Amana W10233410A - page 11

    11 3. Co nn e ct gro u nd wi re (g re en or b are ) o f d i rec t w i re c a bl e t o external ground conductor screw . Tighten scre w . A B C D E F A. Extern al ground conductor screw B. Ground wire (green or bare) of power supply cable C. ¾" (19 mm) UL listed strain relief D. Center , silver -colored terminal block screw E. Neutral g round ...

  • Amana W10233410A - page 12

    12 3-wire connection: Dir ect wir e Use where local co d es permit connecting ca b inet-g roun d con d uctor to ne utral wire. Dire ct wire ca ble must have 5 ft (1.52 m) of extra length s o dryer ca n be moved if needed . Strip 3½" (89 mm) of outer coveri ng from end of cable. Strip insulation back 1" (25 mm). If using 3-wire cable with ...

  • Amana W10233410A - page 13

    13 V enting Requir ements W ARNIN G Fire Hazar d Use a heavy metal vent. Do not use a plastic vent. Do not use a metal foil vent. Failure to follow these instructions can result in d eath or re. W ARNING: T o r educe the risk of fir e, this dryer MUST BE EXHAUSTED OUTDOORS. IMPORT ANT : O bserve all governing codes and ordinances. The dryer exha ...

  • Amana W10233410A - page 14

    14 ■ Do not use an exhaust hood with a magnetic latch. Improper ventin g can cause moistur e and lint to collect indoors, which may result in: Moi s ture damage to woodwork, furniture, paint, wallpaper, carpet s , etc. Hou s ecleaning problem s and health problem s . Plan V ent Syst em Choose your exhaust installation type Recommen d e d exhaust ...

  • Amana W10233410A - page 15

    15 Alter nate installat ions for close clearances V enting systems come in many vari eties. Select the type best for your installation. T wo close-clearance installations are shown. Refer to the manufacturer’ s instructions. A B A. Over -the-top installation (al so available with one offset elbow) B. Periscope installation NOTE: The following kit ...

  • Amana W10233410A - page 16

    16 Inst all Le veling Legs W ARNING Excessive Wei g ht Hazard Use two or more people to move and install dryer. Failure to do so can result in back or other injury. 1. T o protect the floor , use a large flat piece of cardboard fr om the dryer carton. Place ca rdboar d under the entir e back edge of the dryer . 2. Firmly grasp the body of the dry e ...

  • Amana W10233410A - page 17

    17 5. Rotate outer door 180°. 180˚ Reverse hinge 1. Use a small flat-blade scr ewdriver to remove 2 plug strips from the inner door . Slide the head of the screwdriver under the plugs, being certain not to scratch the inner door surface. Lift up. 2. Remove the 4 screws that attach to the inn er door hinge and move the hinge to the other side. Rei ...

  • Amana W10233410A - page 18

    18 Reinstall the d oor 1. Reattach door to dryer front panel with the 4 screws. A B A. Dr yer front panel B. Door assembly 2. Check for fingerprints on the glass. Clean glass if necessary . Close door and chec k that it latches secur ely . Complet e Inst allation 1. Check that all parts are now insta lled. If there is an extra part, go back through ...

  • Amana W10233410A - page 19

    19 DRYER USE Starting Y our Dryer W ARNING Explosion Hazard Keep ammable materials and vapors, such as g asoline, away from dryer. Do not dry anythin g that has ever had anythin g ammable on it (even after washin g ). Failure to follow these instructions can result in death, explosion, or re. W ARNING Fire Hazar d No washer can completely ...

  • Amana W10233410A - page 20

    20 T o use a Time d Cycle ■ Select a Ti med Cycle. ■ Press MORE TIME or LESS TI ME until the desired drying time is displayed. T ap MORE TIME or LESS TIME and the time will change by 1-minute intervals. Press and hold MORE TIME or LESS TIME, and the time will change by 5-minute intervals. NOTE: Th e Timed Cycle Adjust featur e can be used only ...

  • Amana W10233410A - page 21

    21 Damp The Damp light illuminates in an Auto Cycle when the laundry is approximately 80% dry . Cool Down The Cool Down light illuminates during the cool down part of the cycle. Laundry cools for ease in handli ng. Clothes Dry The Clothes Dry light illuminates when the drying cycle is finished. This indicator sta ys on during WRINKLE PREVENT . WRIN ...

  • Amana W10233410A - page 22

    22 Modifiers Use Modifiers to select temperatures for the Timed Cycles only . Press TEMPE RA TURE until the desir ed temperature setting glows. T emperatur e modifiers cannot be used with the Auto Cycles. Air Dry Use the Air Dry Modifier for items that requir e drying without heat such as rubber , plastic and heat-sensitive fabri cs. This table sho ...

  • Amana W10233410A - page 23

    23 T o use the d rying rack Do not remove the lint scre en. 1. Op en dryer door . A A. Front edge 2. Place drying rack inside dryer drum, positioning the back wire on the ledge of the inner dryer ba ck panel. Push down on front edge of dr ying rack to secure over the lint screen. A B A. Dr ying rack front edge B. Dr yer back panel 3. Put the wet it ...

  • Amana W10233410A - page 24

    24 DRY ER CAR E Cleaning the Dry er L ocation Keep dryer ar ea clear and fre e from items that would obstru ct the flow of combustion and ventilation air . Cleaning the Lint Scr een Every loa d cleaning The lint screen is located in th e door opening of the dryer . The control panel has an indicator light to remind you to clean the lint screen befo ...

  • Amana W10233410A - page 25

    25 Va c a t i o n a n d M o v i n g C a r e V acation care Operate your dryer only when you are at home. If you will be on vacation or not using your dryer for an extended period of time, you should: 1. Unplug dryer or disconnect power . 2. Clean li nt screen. See “Cleaning the Lint Scre en.” Moving car e For power supply cor d -connecte d d ry ...

  • Amana W10233410A - page 26

    26 ■ Is the clothing knotte d or b alle d up? When balled up, the load will bounce, causing the dryer to vibrate. Separate the load items and restart the dryer . Dryer d isplaying co d e message ■ “PF” (power failure) , check the following: W as the drying cycle inter rupted by a power failur e? Press POWER, and then press and hold ST ART t ...

  • Amana W10233410A - page 27

    27 Lint on loa d ■ Is the lint screen clogge d ? Clean lint screen. Check for air movement. Stains on loa d or d rum ■ Wa s d ryer fa b ric softener pr operly use d ? Add dryer fabric softener sh eets at the beginning of the cycle. Fabric softener sheets added to a partially dried load can stain your garments. Drum stains ar e caused by dyes in ...

  • Amana W10233410A - page 28

    AMANA ® LA UNDR Y W ARRANTY LIMITED WARRANTY For one year from the date of purchase, when this major appliance is operated and main tained according to instructions attached to or furni shed with the product, Amana brand of Whirlpool Corporation or Whirlpool Can ada LP (hereafter “Amana”) will pay for factor y specified parts and r epair labor ...

メーカー Amana カテゴリー Clothes Dryer

Amana W10233410Aのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- W10233410Aの取扱説明書
- Amanaの製品カード
- パンフレット
- またはAmana W10233410Aの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Amana W10233410Aの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Amana W10233410Aの取り付け説明書、サービスマニュアル、簡易説明書、またはAmana W10233410Aのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Amana W10233410Aの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Amana W10233410Aデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがAmana W10233410Aを使用するのを助ける技術的文書のことです。説明書は通常、全てのAmana W10233410Aユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Amanaの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Amana W10233410Aの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははAmana W10233410Aの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Amana W10233410Aに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Amana W10233410Aデバイスの基本機能を使うにあたってのヒント。 Amana W10233410Aのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Amana W10233410Aに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるAmana W10233410Aのメーカー/サービスへの連絡先に関する情報。

Amana W10233410Aについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもAmana W10233410Aの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがAmana W10233410Aで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)