-
Viper FANG 18C - page 1
SCRUBBER USER MANUAL Model: F ANG 18C VIPER CLEANING EQUIPMENT CO., L TD Address: Liangbian village, Liaobu town, Dongguan city , Guangdong Province, CHINA ...
-
Viper FANG 18C - page 2
USE R MANUAL ENGLISH T ABLE OF CONTENTS INTRODUCTION ..... . ... . .. ... ... . ... . .. . .. . ... . .. .. ... . ... . .. . .. . ... . .. .. ... . ... . .. . .. . ... . .. .. ... . ... . .. . .. . ... . .. .. ... . ... . .. .. .. . ... . .. ... .. ... . .. . .. . ... . .. .. ... . ... . ... 2 MA NU AL PURPOS E AN D CONTENTS . ... .. ... . .. . .. ...
-
Viper FANG 18C - page 3
ENGLISH USER MANUAL INTRODUCTION NOTE The numbers in brackets refer to the co mponents shown in Machine Description chapter . MANUAL PURPOSE AND CONTENTS The purpose of this Manual is to provide the operator with all necessary information to use the machine properly , in a safe and autonomous way . It contains information about technical data, safe ...
-
Viper FANG 18C - page 4
USER MANUAL ENGLISH CHANGES AND IMPROVEM ENTS Viper constantly improves its products and reserves the right to make changes and improvements at its discretion without being obliged to apply such bene fi ts to the machines that were previously sold. Any change and/or addition of accessories must be approved and performed by Viper. OPERA TION CAP AB ...
-
Viper FANG 18C - page 5
ENGLISH USER MANUAL GENERAL INSTRUCTI ONS Speci fi c warnings and cautions to inform about pot ential damages to people and machine are shown below . D ANGER! – Always disconnect the power supply cable when th e machine is not in use, before performing maintenance procedures, before replacing the parts before opening any access panel. – This m ...
-
Viper FANG 18C - page 6
USER MANUAL ENGLISH – While using this machine, take care not to cause damage to people or objects. – Do not bump into shelves or scaff oldings, especially where there is a risk of falling objects. – Do not put any can containing fluids on the machine. – The machine working temperature must be between 0°C and +40°C. – The machine storag ...
-
Viper FANG 18C - page 7
E N G L I S USER MANUAL ENGLISH MACHINE DESCRIPTION MACHINE STRUCTURE 1. Solution Tank 2. Recovery Tank 3. Clear Cover 4. Control Box 5. Switch lever 6. Drain Hose 7. Vacuum Hose 8. Water Hose 9. Squeegee Assembly 10. Transport Wheels 11. Bumper 12. Skirt 13. Brush Motor Switch 14. Vacuum Motor Switch 15. Knob 16. P l a t e 3 4 2 5 6 7 1 1 2 8 1 5 ...
-
Viper FANG 18C - page 8
USER MANUAL ENGLISH ACCESSORIES/OPTIONS In addition to the standard components, the machine c an be equipped with the following accessories/options, according to the machine specific use: 1 ． Brush 2 ． Pad driver For further information concer ning the optional accessories, c ontact an authorised Retailer. TECHNICAL DA T A Model FANG 18C Soluti ...
-
Viper FANG 18C - page 9
ENGLISH USER MANUAL WIRING DIAGRAM FOR FANG 18 C 8 FANG 18C 80188EU(1)2009-01 ...
-
Viper FANG 18C - page 10
USER MANUAL ENGLISH USE SCRUBBER SETUP N O T E Read operators manual thoroughly prior to operating or servicing this machine!!! a) PRE-OPERA TION CHECKS 1. Sweep the outside of the machine. 2. Make sure the voltage of machine conform to local voltage. (220-240V) 3. Check that squeegee is properly installed. 4. Check that brush / pad is properly ins ...
-
Viper FANG 18C - page 11
ENGLISH USER MANUAL BASIC OPERA TION WARNING! Do not operate machine unless you have read and understand this manual. 1. Adjust control housing to a comfortable oper ating height by squeezing together the two thumb levers directly underneath the housing. 2. Lower squeegee assembly to the floor . 3. T urn ...
-
Viper FANG 18C - page 12
USER MANUAL ENGLISH ENGLISH DRAINING T ANKS a) DRAINING SOLUTION T ANK NOTE Any time scrubbing operation is completed, the solution tank should be drained and cleaned. 1. Pull down on the clear tube (back left of the machine) to remove it from the hose barb. This will allow the solution to flow freely into a bucket or floor drain. 2. Rinse the solu ...
-
Viper FANG 18C - page 13
ENGLISH USER MANUAL MAINTENANCE T o keep the machine performing well for many years, please follow the followi ng maintenance procedures. W ARNING! Always confirm that the machine is unplugged prior to performing any maintenance or repairs! W ARNING! Repairs are to be completed by Authorized Service Centers only . Any repairs completed by unauthori ...
-
Viper FANG 18C - page 14
USER MANUAL ENGLISH F i g . 4 BRUSH/PAD CLEANING CAUTION! It is advisable to wear pr otective gloves when cleaning the brush/pad because there may be sharp debris. 1. Remove the brush/pad from the ma chine, as shown in Use chapter. 2. Clean and wash the brush/pad with water and detergent. 3. Check the brush bristles for integrity and wear; if neces ...
-
Viper FANG 18C - page 15
ENGLISH USER MANUAL TROUBLESHOOTING PROBLEM CAUSE SOLUTION No Power The wiring not connected correctly or bad wiring Check the wiring or contact Viper Distributor Bad brush motor Contact Viper Distributor Carbon brushes worn out Contact Viper Distributor Vacuum motor does not run The wiring not connected correctly or bad wiring Check the wiring or ...
-
Viper FANG 18C - page 16
USER MANUAL ENGLISH ST ORAGE W ARNING! If you are storing the machine in an area which can freeze, be sure both tanks and the solution plumbing are empty of all water and dry! 1. Always store the machine indoors. 2. Always store the machine in a dry area. 3. Always take off the pad driver / brush 4. Always store the machine with the squeegee assemb ...
Viper FANG 18Cについてご質問がありますか？
次のフォームを使用してください
見つけた説明書を読んでもViper FANG 18Cの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがViper FANG 18Cで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。