日本語 dropdown-ico

Smeg GKC64-3の取扱説明書

20ページ 2.47 mb
ダウンロード

ページに移動 of 20

Summary
  • Smeg GKC64-3 - page 1

    Contents 23 1 INSTRUCTIONS FOR SAFE AND PROPER USE ____________________ 24 2 POSITIONING OF THE HOB ____________________________________ 26 3 ELECTRICAL CO NNECTION ____________________________________ 28 4 GAS CONNECT ION ___________________________________________ 29 5 ADAPTATION TO DIFFER ENT TYPES OF GAS _____________________ 31 6 FINAL OPER AT ...

  • Smeg GKC64-3 - page 2

    Introduction 24 1 INSTRUCTIONS FOR SAFE AND PROPER USE THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE AND THEREFORE MUST BE KEPT IN ITS ENTIRETY AND IN AN ACCESSIBLE PLACE FOR THE WHOLE WORKING LIFE OF THE COOKING HOB. WE ADVISE READING THIS MANUAL AND ALL THE INSTRUCTIONS THEREIN BEFORE USING THE COOKING HOB. ALSO KEEP THE SERIES OF NOZZLES SUPP ...

  • Smeg GKC64-3 - page 3

    Introduction 25 THE IDENTIFICATION PLATE, WITH TECHNICAL DATA, SERIAL NUMBER AND MARKING IS CLEARLY VISIBLE UNDER THE CASING. THE PLATE ON THE CASING MUST NOT BE REMOVED. BEFORE CONNECTING THE DEVICE, MAKE SURE THAT IT HAS BEEN REGULATED FOR THE TYPE OF GAS THAT WILL FEED IT, CHECKING THE LABEL UNDER THE HOB. DO NOT PUT PANS WITHOUT PERFECTLY SMOOT ...

  • Smeg GKC64-3 - page 4

    Instructions for the installer 26 2 POSITIONING OF THE HOB The following operation requ ires building and/or carpentr y work so must be carried out by a competent tradesman. Installation can be carried out on vari ous materials such as masonry, metal, solid wood or plastic laminat ed wood as long as they are heat resistant (T 90°C). 2.1 Attachment ...

  • Smeg GKC64-3 - page 5

    Instructions for the installer 27 Bracket ‘ A ’ in the 1st slot Bracket ‘ A ’ in the 2nd slot Bracket ‘ B ’ 2.2 Fixing 90 cm hobs on 60 cm base unit If a 90 cm hob is to be bracketed to a 6 0 cm base unit, 2 centra l brackets “ A ” have to be us ed in addition to the side brackets “ B ” as shown in the drawin g below. The gas co ...

  • Smeg GKC64-3 - page 6

    Instructions for the installer 28 3 ELECTRICAL CONNECTION Make sure that the voltage and capacity of the pow er line conform to the data shown on the plat e located under the casing. Do not remov e this plate for any reason. The plug on th e end of the supply cable and the wall soc ket must be the same type and conform to the curr ent electrical sy ...

  • Smeg GKC64-3 - page 7

    Instructions for the installer 29 4 GAS CONNECTION Connection to the gas mains may be made with a rigid copper pipe or with a flexible pipe and conforming to the pr ovisions defined by standard regulations in force. To facilitate connection, fitting A on the r ear of the appliance m ay be adjusted laterally. For this purpose, loosen h exagon nut B ...

  • Smeg GKC64-3 - page 8

    Instructions for the installer 30 4.1 Connection to LPG Use a pressure regul ator and make the connection to the tank according to the provisio ns of standards regulations in force. Make sur e that feed pressure conforms to the leve ls shown in the tab le in paragraph “ 5.3 Regulation for LPG”. 4.2 Ventilation of rooms The hob may be inst alled ...

  • Smeg GKC64-3 - page 9

    Instructions for the installer 31 5 ADAPTATION TO DIFFERENT TYPES OF GAS Before performing any c leaning or mainten ance work, disconnect the appliance from the electrical socket. The hob has be en inspected for G25 (2L3B/P) natural gas at a pressure of 25 mbar. For function ing with other types of gas the nozzles must be replaced and the primary a ...

  • Smeg GKC64-3 - page 10

    Instructions for the installer 32 following the instructions given in the tables for bottled gas G30/G31 – 28/37 mbar. The nozzle mus t not be tightened to a tor que of over 3 Nm. Regulate the air flow by moving the Venturi pipe “ C ”, until the gap “ A ” is as shown in the table in point “ 5.5 Regulation of primary air” and fix it wi ...

  • Smeg GKC64-3 - page 11

    Instructions for the installer 33 5.4 Regulation for G25/25 mbar The hob has been ins pected for G25 (2L3B/P) at a pressure of 2 5 mbar. To allow the unit to work wit h this type of gas, perform the same operations described in paragrap h “ 5.3 Regulation for LPG”, but choose the nozzles and r egulate the prim ary air for natural gas, as shown ...

  • Smeg GKC64-3 - page 12

    Instructions for the installer 34 5.5 Regulation of primary air Referred to distance “ A ” in mm. 60 cm hobs with separable control panel. Burner G25 25 mbar G30/G31 28/37 mbar Auxiliary (1) 2.5 2.5 Semirapid r (2) 0.5 2.0 Semirapid l (3) 0.5 1.5 Rapid large (4) 0 2.5 Ultrarapid (5) 2.0 4.0 90 cm hobs with separable control panel. Burner G25 25 ...

  • Smeg GKC64-3 - page 13

    Instructions for the installer 35 6 FINAL OPERATIONS Having carried out the above adjustments, reassemble t he appliance following, backwards, the inst ructions in paragraph “ 5.1 R emoving the separable control pa nel / 5.2 Removing the hob”. 6.1 Regulation of minimum for natural gas Reposition the components on the burner and slide the knobs ...

  • Smeg GKC64-3 - page 14

    Instructions for the installer 36 6.3 Arrangement of the burners on the hob (Hob with separable control panel) 60 cm. hob BURNERS 1. Auxiliary 2. Semirapid r 3. Semirapid l 4. Rapid large 5. Ultrarapid 90 cm. hob BURNERS 1. Auxiliary 2. Semirapid 3. Rapid 4. Fish burner 5. Ultrarapid ...

  • Smeg GKC64-3 - page 15

    Instructions for the installer 37 6.4 Arrangement of the burners on the hob (Hob with built-in control panel). 60 cm. hob BURNERS 1. Auxiliary 2. Semirapid r 3. Semirapid l 4. Rapid 5. Ultrarapid 6.5 Lubrication of gas taps With time it may happen that the gas taps get blocked and h ard to turn. Clean them inside and r e-grease them. This operation ...

  • Smeg GKC64-3 - page 16

    Instructions for the user 38 7 USING THE HOB Before turning on the burners, make sure that the burner rings, caps and grids have been fitted cor rectly. In the ultrarapid burner, notch A must be aligned with pin B . Grid C provided is intended for use with wok s (Chinese pans). Adapter D com es only with open grids models and is intended for us e w ...

  • Smeg GKC64-3 - page 17

    Instructions for the user 39 while coo king, all pans o r griddles mu st be positioned within the cook ing hob perimeter and must be a minimum distance of 3-4 cm from the knobs. 7.3 Diameter of the pans Burners Ø min. and max. (en cm.) Auxiliary 12-14 Semirapid 16-20 Rapid medio 22-26 Rapid large 22-26 Ultrarapid 22-26 Fish burner Special oval-sha ...

  • Smeg GKC64-3 - page 18

    Instructions for the user 40 or fish. 5 Strong For roasts, steaks and large boil ed joints. 6 Very strong To boil large amounts of water, to fry. WARNING When switching on the electric element for the first time, or if the electric element has not been used for a long time, to remove any humi dity from the insulating material it should be dr ied ou ...

  • Smeg GKC64-3 - page 19

    Instructions for the user 41 8 CLEANING AND MAINTENANCE Never use a steam jet to clean the appliance. Before any intervention, disconnect the power supply of the device. 8.1 Cleaning Clean the cooking top regul arly every time you use it, obviously after it has cooled. 8.1.1 Regular daily cleaning of the hob In order to clean an d preserve the surf ...

  • Smeg GKC64-3 - page 20

    Instructions for the user 42 8.2 Cleaning of cooking hob components CAUTION: do not wash these components in a dishwasher. In normal use of the hob, the stai nless steel b urner caps and pan- stands tend to be burnishe d by the high temperature. Clea n these parts using very fine abrasive sponges or simil ar commercial products. Then use a specific ...

メーカー Smeg カテゴリー Cooktop

Smeg GKC64-3のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- GKC64-3の取扱説明書
- Smegの製品カード
- パンフレット
- またはSmeg GKC64-3の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Smeg GKC64-3の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Smeg GKC64-3の取り付け説明書、サービスマニュアル、簡易説明書、またはSmeg GKC64-3のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Smeg GKC64-3の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Smeg GKC64-3デバイスの取扱説明書はどのようなものですか？
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがSmeg GKC64-3を使用するのを助ける技術的文書のことです。説明書は通常、全てのSmeg GKC64-3ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Smegの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Smeg GKC64-3の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははSmeg GKC64-3の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Smeg GKC64-3に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Smeg GKC64-3デバイスの基本機能を使うにあたってのヒント。 Smeg GKC64-3のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Smeg GKC64-3に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるSmeg GKC64-3のメーカー/サービスへの連絡先に関する情報。

Smeg GKC64-3についてご質問がありますか？

次のフォームを使用してください

見つけた説明書を読んでもSmeg GKC64-3の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがSmeg GKC64-3で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

Captcha
新しい画像

コメント (0)