-
Graco Inc. 309410 - page 1
S Controls 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . S Setup 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . S Startup 8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . S Digital T racking System (DTS) 12 . . . . . . . S Cleanup 19 . . . . . . . . . . . . . . . . . . . . . . . . . . ...
-
Graco Inc. 309410 - page 2
309410 2 Danger d’incendie et d’explosion : les gaz de solv ant et de peinture peuvent s’enfl ammer ou ex ploser . Pour éviter les risq ues d’ incendi e et d’exp losion : N ’utiliser l’appareil qu e dans une zon e extrêmem ent bien aérée. Éliminer toute source d’i nflammation ; tel le que veilleuses, cigarettes et arcs ...
-
Graco Inc. 309410 - page 3
3 309410 CONTROLS / CONTROLES / COMMANDES / CONTROLES On/Off Switch Interruptor de ligar e desligar Interrupteur marche/arrêt Interruptor de encendido/apagado Drain V alve Válvula de drenagem Vidange Válvula de vaciado On/Off Switch Interruptor de ligar e desligar Interrupteur marche/arrêt Interruptor de encendido/apagado On/Off Switch Aan/Uit ...
-
Graco Inc. 309410 - page 4
309410 4 1. Disconnect engine power cord. 2. Release tension bar . Setup 3. Remove engine; tilt and slide back. 4. Install motor; drop in and push forward. Change Engine to Motor Release ...
-
Graco Inc. 309410 - page 5
5 309410 5. Look through side vent holes and ensure drive belt is in motor pulley . 6. Secure motor with tension bar . Setup 7. Plug in pressure control power cord. Change Engine to Motor Engage ...
-
Graco Inc. 309410 - page 6
309410 6 1. Connect appropriate Graco high-pressure hose to sprayer . T ighten securely . 2. Connect other end of hose to gun. Setup 3. T ighten securely . 4. Remove tip guard. Note: Remove second gun port cap for multiple guns and repeat steps 1 – 4, 7, 8, 10 ...
-
Graco Inc. 309410 - page 7
7 309410 5. Install clean inlet strainer . 6. Fill throat packing nut with TSL to prevent premature packing wear . Do this each time you spray and store. 7. Check engine oil level. Add SAE 10W–30 (summer) or 5W–20 (winter), if necessary . 8. Fill fuel tank. 9. Ground sprayer with grounding clamp. Approximate Fill Level (cold) Setup ...
-
Graco Inc. 309410 - page 8
309410 8 1. Place suction tube and drain tube in grounded metal pail partially filled with flushing fluid. Attach ground wire to pail and to true earth ground. 2. T urn prime valve down. T urn pressure control to lowest pressure. Startup 3. Set pump switch OFF . P AINT FLUSH ...
-
Graco Inc. 309410 - page 9
9 309410 Startup a. Move fuel valve to open b. Move choke to closed c. Set throttle to fast d. Set engine switch ON e. Pull starter cord f. After engine starts, move choke to open g. Set throttle to desired setting – Digital display is functional after engine starts – 4. Start engine a. b. c. d. e. f. g. Start motor ...
-
Graco Inc. 309410 - page 10
309410 10 Note: Inspect fittings for leaks. Do not stop leaks with your hand or a rag! If leaks occur , turn sprayer OFF immediately . Do Pressure Relief in Cleanup, 1. – 3. on page 19. T ighten leaky fittings. Repeat Startup, 1. – 5 . If no leaks, continue to trigger gun until system is thoroughly flushed. Proceed to 6. Startup 5. Set pump swi ...
-
Graco Inc. 309410 - page 11
11 309410 9. Place siphon tube in paint pail. 10. T rigger gun again into flushing fluid pail until paint appears. Assemble tip and guard, page 1 1. SwitchTip and Guard Assembly 1. Engage trigger safety . 2. Insert SwitchT ip . Insert seat and OneSeal . 3. Screw assembly onto gun. Hand tighten. FLUSH P AINT SwitchT ip OneSeal seat Startup s ...
-
Graco Inc. 309410 - page 12
309410 12 Digital T racking System (DTS) Close cover when spraying to protect from overspray Operation Main Menu 1. Do Startup steps 1. – 3. 2. Start engine or motor , page 9. Sprayer Model momentarily displays, e. g., C5900 = GMax 5900 Convertible Note: Information other than pressure can not be accessed if system pressure is greater than 20 ...
-
Graco Inc. 309410 - page 13
13 309410 Digital T racking System (DTS) 3. Short press DTS button to move to Job Gallons (or Liters x 10). 4. Press and hold to reset to zero, or short press DTS button to move to Lifetime Gallons (or Liters x 10). 5. Short press DTS button to move to Auto- Clean T imer operation (Manual 309278). Note: LIFE displays briefly , then the number of ga ...
-
Graco Inc. 309410 - page 14
309410 14 W atchDog Pump Protection System Pump stops automatically when material pail is empty . 1. Do Startup . 2. Press and hold DTS button, release when ON is displayed. Note: GAL (or LITER) flashes while pump protection system is active. EMPTY displays and the pump stops when pump protection system detects an empty material pail. 3. T urn ...
-
Graco Inc. 309410 - page 15
15 309410 Secondary Menu – Stored Data and W atchDog Pump Protection Modes 1. Do Startup steps 1. – 3. Pressure must be at zero. 2. Start engine or motor , page 9. Pressure display appears. 3. Simultaneously press DTS button and set pump on/of f switch on. Resettable Hour Meter appears. Sprayer model momentarily displays, e.g., C5900 = GMAX 590 ...
-
Graco Inc. 309410 - page 16
309410 16 Secondary Menu – Stored Data and W atchDog Pump Protection Modes 4. Press and hold to reset to zero, or 5. Short press DTS button to move to Lifetime Hour Meter . 6. Short press DTS button to move to TOT AL Gallons (all pressures). 7. Press DTS button to move to stored error code. Press and hold DTS button to clear error code to E=00. S ...
-
Graco Inc. 309410 - page 17
17 309410 9. Short press DTS button again to move to W atchDog MAN (manual) mode. 10. Press and hold to switch between MAN (stan- dard) and AUTO mode. In AUT O mode, W atchDog pump protection is active once pressure is over 1500 psi (103 Bar , 10.3 MPa) 1 1. Short press to return to step 3. 12. T urn pump switch OFF at any time to exit stored data ...
-
Graco Inc. 309410 - page 18
309410 18 heavy edges Spray T est Pattern Clearing Tip Clogs 1. T rigger gun and spray test pattern. Slowly adjust pressure to eliminate heavy edges. Use smaller tip size if pressure adjustment can not eliminate heavy edges. 2. Hold gun perpendicular , 10–12 in. (25–30 cm) from surface. Spray back and forth. Use strokes overlapped by 50%. Start ...
-
Graco Inc. 309410 - page 19
19 309410 Cleanup 1. Set pump switch OFF . T urn engine or motor OFF . 2. T urn pressure to lowest setting. T rigger gun to relieve pressure. 3. T urn prime valve down. Perform AutoClean procedure (Manual 309278) or follow conventional flushing procedure that follows: 4. Remove guard and SwitchT ip. Pressure Relief Pressure Relief Pressure Relief P ...
-
Graco Inc. 309410 - page 20
309410 20 5. Unscrew bowl, remove filter . As- semble without filter . Clean filter . 6. Clean filter , guard and SwitchT ip in flushing fluid. 7. Remove siphon tube set from paint and place in flushing fluid. Use water for water base paint and mineral spirits for oil base paint. FLUSH P AINT FLUSH ...
-
Graco Inc. 309410 - page 21
21 309410 8. T urn engine ON and start engine or motor . Set pump switch ON. 9. T urn prime valve horizontal. 10. T urn pressure control up until motor begins to drive pump. Hold gun against paint pail. T ake trigger safety OFF . T rigger gun until flushing fluid appears. 1 1. Move gun to flushing pail, hold gun against pail, trigger gun to thoroug ...
-
Graco Inc. 309410 - page 22
309410 22 Caution: If flushing with water , do not leave water in sprayer . Flush again with mineral spirits, oil or Pump Armor and leave this protective coating in the sprayer to help prevent freezing or corrosion and increase sprayer life. 13. Raise siphon tube above flushing fluid and run sprayer for 15 to 30 seconds to drain fluid. T urn pump s ...
-
Graco Inc. 309410 - page 23
23 309410 DTS Error Codes Service 309409 Reference Repair Manual 309409 or 30941 1 or call your distributor for service ...
-
Graco Inc. 309410 - page 24
309410 24 Graco W arranty Graco warrants all equipment listed in this manual which is manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale by an authorized Graco distributor to the original purchaser for use. With the exception o f any special extended or limited warranty published by Gr ...
Graco Inc. 309410についてご質問がありますか?
次のフォームを使用してください
見つけた説明書を読んでもGraco Inc. 309410の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがGraco Inc. 309410で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。