-
Delta Electronics Series E24SR - page 1
(2.30” x 0.90” x 0.39”) SMD and Through-hole versions Industry standard pin out 2:1 input range Fixed frequency operation Input UVLO, Output OTP , OCP , OVP Basic insulation 2250V isolation Monotonic startup into normal and pre-biased loads Output voltage trim ± 10% No minimum load required ISO 900 ...
-
Delta Electronics Series E24SR - page 2
DS_E24SR05012_010 32008 2 TECHNICAL SPECIFICA TIONS (T A =25°C, airflow rate=300 LFM, V in = 24 Vdc, nominal V out unless otherw ise noted.) PA R A M E T E R NOTES and CONDITIONS E24SR05012 (St andard) Min. T yp. Max. Un its ABSOLUTE MAXIMUM RA TINGS Input V oltage Continuous 36 Vdc T ransient (100ms) 100ms 50 Vdc Operating T emperature Refer to f ...
-
Delta Electronics Series E24SR - page 3
DS_E24SR05012_010 32008 3 ELECTRICAL CHARACTERISTICS CUR VES 80 82 84 86 88 90 92 24 68 1 0 1 2 Output C ur r ent ( A ) E ff i ci en cy (%) 1. 0 2. 0 3. 0 4. 0 5. 0 6. 0 7. 0 2468 1 0 O utput C ur r ent ( A ) L o ss (W ) 18Vin 1 2 Figure 1: Ef ficiency vs. load current for minimum, nomi nal, and maximum in put voltage at 25°C Figure 2: Power dissi ...
-
Delta Electronics Series E24SR - page 4
DS_E24SR05012_010 32008 4 ELECTRICAL CHARACTERISTICS CUR VES For Negative Remote On/Off Logic Figure 4: T urn-on transi ent at full rated load current (resi stive load) (2 ms/div). Vin=24V . T op T race: V out, 2.0V/div; Bottom T race: ON/OFF input, 10V/div Figure 5: T urn-on trans ient at zero load current (2 ms/ div). Vin=24V . T op T race: V out ...
-
Delta Electronics Series E24SR - page 5
DS_E24SR05012_010 32008 5 ELECTRICAL CHARACTERISTICS CUR VES Figure 8: Output voltage response to step-change in load current (75%-50%-75% of Io, max; di/dt = 0.1A/µs). Load cap: 10µF t antalum capacitor and 1µF ceramic capacitor . 0 T op T race: Vout (100mV/div , 200us/div ) , Bottom T r ace: Iout (5 A /div). Scope measureme nt should be made u ...
-
Delta Electronics Series E24SR - page 6
DS_E24SR05012_010 32008 6 ELECTRICAL CHARACTERISTICS CUR VES Strip Copper Vo(-) Vo(+) 10u 1u SCOPE RESISTIV E LOAD Figure 12: Input reflected ripple current, i s , through a 12µH source inductor at nominal input voltage and rated loa d current (20 mA/div , 2us/div) Figure 13: Output voltage noise and ripple measur ement test setup 0. 0 2. 0 4. 0 6 ...
-
Delta Electronics Series E24SR - page 7
DS_E24SR05012_010 32008 7 The input source must be insulated from the ac mains by reinforced or double insulation. The input terminals of the module are not operator accessible. If the metal baseplate is grounded , one Vi pin and one Vo pin shall also be grounded. A SELV reliability test is conducted on the system where the module i ...
-
Delta Electronics Series E24SR - page 8
DS_E24SR05012_010 32008 8 Vi(-) ON/OFF Vi(+) Vo(-) Trim Vo(+) Sense(-) Sense(-) Vi(-) ON/OFF Vi(+) Vo(-) Trim Vo(+) Sense(-) Sense(-) Figure 16: Remote on/off implementation Remote Sense Remote sense compen sates for voltage dro ps on the output by sensing the actual output volt age at the point of load. The voltage bet ween the remote sense pins a ...
-
Delta Electronics Series E24SR - page 9
DS_E24SR05012_010 32008 9 FEA TURES DESCRIPTIONS (CON.) Output V oltage Adjustment (TRIM) To increase or decrea se the output voltage set poin t, connect an external re sistor between the TRIM pin and either the SENSE(+) or SENSE(-). The TRIM pin should be left open if this feature is not used. Figure 18: Circuit configuration for trim-down (decrea ...
-
Delta Electronics Series E24SR - page 10
DS_E24SR05012_010 32008 10 THERMAL CONSIDERA TIONS Thermal management is an important part of the syst em design. To ensure p roper, reliable operation, sufficie nt cooling of the power mod ule is needed over the entire temperature range of the modul e. Convection coolin g is usually the dominant mode of heat transfer. Hence, the choice of equipmen ...
-
Delta Electronics Series E24SR - page 11
DS_E24SR05012_010 32008 11 P I C K A N D P L A C E L O C A T I O N S U R F A C E - MOUNT T APE & REEL RECOMMENDED P AD LA YOUT (SMD) ...
-
Delta Electronics Series E24SR - page 12
DS_E24SR05012_010 32008 12 LEADED (Sn/Pb) PROCESS RECOMMEND TEMP . PROFILE T ime ( sec. ) Pre-h eat tem p. 140~180 ° C 60~120 sec. Peak tem p. 210~230 ° C 5sec . Ramp-up te mp. 0.5~3.0 ° C /sec . T emperature ( ° C ) 50 100 150 200 250 300 60 0 120 180 240 2nd Ramp-up temp. 1.0~3.0 ° C /sec. Over 200 ° C 40~50sec. Cooling down rate <3 ° C ...
-
Delta Electronics Series E24SR - page 13
DS_E24SR05012_010 32008 13 MECHANICAL DRA WING Surface-mount module Through-hole module Pin No. Name Function 1 -Vin Negative input voltage Remote ON/OFF Positive input voltage Positive output voltage Positive remote sense Output voltage trim Negative remote sense Negative output voltage 2 3 4 5 6 ON/OFF +Vin +V out +SENSE TRIM -SENSE -V out 7 8 ...
-
Delta Electronics Series E24SR - page 14
DS_E24SR05012_010 32008 14 P ART NUMBERING SYSTEM E 24 S R 050 12 N R F A T ype of Product Input V oltage Number of Output s Product Series Output V oltage Output Current ON/OFF Logic Pin Length/T ype Option Code E - Eighth Brick 24V S - Single R - Regular 050 - 5.0V 12 - 12A N - Negative (Default) P - Positive R - 0.170” (Default) N - 0.145” K ...
-
Delta Electronics Series E24SR - page 15
DS_E24SR05012_010 32008 15 at any time, without notice . ...
Delta Electronics Series E24SRについてご質問がありますか?
次のフォームを使用してください
見つけた説明書を読んでもDelta Electronics Series E24SRの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがDelta Electronics Series E24SRで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。