Napco Security Technologies GEM-P1632の取扱説明書

16ページ 0.18 mb
ダウンロード

ページに移動 of 16

Summary
  • Napco Security Technologies GEM-P1632 - page 1

    R INS TALLATION INS TALLATION INST RUCTIONS INST RUCTIONS GEM-RP3DGT L Digital Ke ypad W I982A 6/99 © Napco 1999 Quick Start: 1. Referring to the control panel wiring diagram, connect siren, aux. power, pgm. output, remote bus, earth ground, zone and telephone wiring. NOTE: See Installation Instructions for the appropriate control panel. 2. Connec ...

  • Napco Security Technologies GEM-P1632 - page 2

    2 ...

  • Napco Security Technologies GEM-P1632 - page 3

    INTRODUCTION The GEM-RP3DGTL is a dual 7-segment digital keypad that is compat ible with the NAPCO GEM-Series GEM-P816, P1632, P3200 & P9600 control-panels. Refer to User Guide OI249 for operation instructions. While the GEM-RP3DGTL may be used to fully program the control, the GEM-RP1CAe2 keypad provides the optimum in ease of keypad programmi ...

  • Napco Security Technologies GEM-P1632 - page 4

    EASY PROGRAM MODE OVERVIEW ENTERING THE EASY KEYPAD PROGRAM MODE 1 Enter the Dealer Security Code (default = 456789) for a new panel or enter your custom Dealer Program Code if programmed and press A 2 Press NO ( F ) repeatedly until function “ 17 “ (Activate Program Mode) is displayed. NOTE: If you pass “ 17 “ you can scroll back by pressi ...

  • Napco Security Technologies GEM-P1632 - page 5

    Total Number of Zones in Area 1 (Appears for New Panel Only) Press the A button and then directly enter the total number of zones to be programmed for Area 1. Valid entries are from 01 to 32. Directly enter the total number of zones, including leading zeros. Use number buttons 1 through 9 . NOTE: Press the 0 button for a zero. The system is based o ...

  • Napco Security Technologies GEM-P1632 - page 6

    Entry/Exit Zones in Area 1 (Appears for New Panel Only) Press the A button and then directly enter the zone number of any zones which are to be used as Entry/Exit zones. Valid entries are from 01 to 32. Di- rectly enter each zone number, including leading zeros. Use number buttons 0 through 9 . Press J to save and then repeat for any additional zon ...

  • Napco Security Technologies GEM-P1632 - page 7

    7 Central Station Receiver 1 Format From the table below, enter the central station's receiver format. Use number buttons 1 through 9 . NOTE: Press G0 for a zero and 0 for a blank space (•). Press G 1 through G 4 for letters B–E, respectively. Press J to save. Press NEXT ( E ) button to proceed. NOTE: Central Station Receiver 2 and 3 Forma ...

  • Napco Security Technologies GEM-P1632 - page 8

    RF Transmitter Programming (For wireless systems only. Also see Quick Method, which follows) Press the A button and for each transmitter (key fob transmitters also), then directly enter: 1 The zone number (01–32) to which the transmitter will be mapped, including leading zeros. 2 The 6-digit RF ID # printed on the transmitter and box. 3 The 1-dig ...

  • Napco Security Technologies GEM-P1632 - page 9

    9 Key Fob Transmitters Keyfobs can be programmed as “Arm/Disarm” devices using the ON and OFF buttons (refer to control panel installation instructions). Press the A button and for each Key Fob Transmitter, enter: 1 The Key Fob Transmitter number (01–15). 2 The area number to which transmitter is assigned (1 or 2); enter 0 to disable keyfob. ...

  • Napco Security Technologies GEM-P1632 - page 10

    Total Number of Zones and Keypads in Area 1. Total Number of Zones and Keypads in Area 2. (Appears for New Panel Only) 1 Press the A button and then press 3 to select the total number of zones to be programmed for Area 1. Valid entries are from 08 to 24 in multiples of 4. 2 Press 2 and press 3 to select the total number of keypads to be programmed ...

  • Napco Security Technologies GEM-P1632 - page 11

    11 Central Station Receiver 1 Format From the table below, enter the central station's receiver format. Use number buttons 1 through 9 . NOTE: Press G0 for a zero and 0 for a blank space (•). Press G 1 through G 4 for letters B–E, respectively. Press J to save. Press NEXT ( E ) button to proceed. NOTE: Central Station Receiver 2 and 3 Form ...

  • Napco Security Technologies GEM-P1632 - page 12

    12 RF Transmitter Programming (For wireless systems only. Also see Quick Method, which follows) Press the A button and for each transmitter and directly enter: 1 The zone number (01–96) to which the transmitter will be mapped, including leading zeros. 2 The 6-digit RF ID # printed on the transmitter and box. 3 The 1-digit checksum number (C) prin ...

  • Napco Security Technologies GEM-P1632 - page 13

    Key Fob Transmitters Keyfobs can be programmed as “Arm/Disarm” devices using the ON and OFF buttons (refer to control panel installation instructions). Press the A button and for each Key Fob Transmitter, enter: 1 The Key Fob Transmitter number (01–15). 2 The area number to which transmitter is assigned (1-8); enter 0 to disable keyfob. 3 The ...

  • Napco Security Technologies GEM-P1632 - page 14

    DIRECT ADDRESS PROGRAM MOD E This is an extension of the Dealer Program Mode. This method of programming is used in conjunction with the Keypad Programming Worksheets contained in the control panel programming guide. Refer to these worksheets to identify the 4-digit location (address) of the feature to be programmed. An illustrative example is prov ...

  • Napco Security Technologies GEM-P1632 - page 15

    15 ...

  • Napco Security Technologies GEM-P1632 - page 16

    NAPCO SECURITY SYSTEMS, INC. (NAPCO) war- rants its products to be free from manufacturing defects in materials and workmanship for thirty-six months fol- lowing the date of manufacture. NAPCO will, within said period, at its option, repair or replace any product failing to operate correctly without charge to the original pur- chaser or user. This ...

メーカー Napco Security Technologies カテゴリー Door

Napco Security Technologies GEM-P1632のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- GEM-P1632の取扱説明書
- Napco Security Technologiesの製品カード
- パンフレット
- またはNapco Security Technologies GEM-P1632の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Napco Security Technologies GEM-P1632の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Napco Security Technologies GEM-P1632の取り付け説明書、サービスマニュアル、簡易説明書、またはNapco Security Technologies GEM-P1632のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Napco Security Technologies GEM-P1632の製品を使用するにあたって最も人気のある説明書を閲覧できます。

Napco Security Technologies GEM-P1632デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがNapco Security Technologies GEM-P1632を使用するのを助ける技術的文書のことです。説明書は通常、全てのNapco Security Technologies GEM-P1632ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Napco Security Technologiesの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Napco Security Technologies GEM-P1632の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははNapco Security Technologies GEM-P1632の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Napco Security Technologies GEM-P1632に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Napco Security Technologies GEM-P1632デバイスの基本機能を使うにあたってのヒント。 Napco Security Technologies GEM-P1632のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Napco Security Technologies GEM-P1632に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるNapco Security Technologies GEM-P1632のメーカー/サービスへの連絡先に関する情報。

Napco Security Technologies GEM-P1632についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもNapco Security Technologies GEM-P1632の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがNapco Security Technologies GEM-P1632で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)