Graco 215363の取扱説明書

18ページ 0.27 mb
ダウンロード

ページに移動 of 18

Summary
  • Graco 215363 - page 1

    Instructions–Parts List Monark r Air Motor For use with Graco fluid handling pumps. 180 psi (1.2 MPa, 12 bar) Maximum Air Working Pressure Model 206955, Series K For ST ANCHION TUBE mounting Model 205997, Series K Model 215363, Series D Model 222791, Series D For 3 tie rod mounting Model 207546, Series H For hinged clamp mounting Important Safety ...

  • Graco 215363 - page 2

    2 307043 T able of Contents W arnings 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installation 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Air Motor Service 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Parts Drawings and Lists Model 207546 10 . . . . . . . . . . . ...

  • Graco 215363 - page 3

    3 307043 W ARNING SKIN INJECTION HAZARD Spray from the gun/dispensing valve, leaks or ruptured components can inject fluid into your body and cause extremely serious injury , including the need for amputation. Fluid splashed in the eyes or on the skin can also cause serious injury . D Fluid injected into the skin might look like just a cut, but it ...

  • Graco 215363 - page 4

    4 307043 W ARNING FIRE AND EXPLOSION HAZARD Improper grounding, poor ventilation, open flames or sparks can cause a hazardous condition and result in a fire or explosion and serious injury . D Ground the equipment and the object being sprayed. Refer to Grounding on page 5. D If there is any static sparking or you feel an electric shock while using ...

  • Graco 215363 - page 5

    5 307043 Installation Grounding W ARNING FIRE AND EXPLOSION HAZARD Before operating the pump, ground the system as explained below . Also read the section FIRE AND EXPLOSION HAZARD on page 4. Proper grounding is an essential part of maintaining a safe system. T o reduce the risk of static sparking, ground the pump. Check your local electrical code ...

  • Graco 215363 - page 6

    6 307043 Air Motor Service Pressure Relief Procedure W ARNING SKIN INJECTION HAZARD The system pressure must be manually relieved to prevent the system from starting or spraying/dispensing acciden- tally . Fluid under high pressure can be injected through the skin and cause serious injury . T o re- duce the risk of an injury from injection, splashi ...

  • Graco 215363 - page 7

    7 307043 Air Motor Service 7. Pull the piston assembly (G) from the air motor base (F), and set it aside. 8. Remove the bearing housing assembly (26 or 27) for all Models except Model 206955. Remove and wipe the seat clean with a cloth. For model 206955, remove retainer ring (3) and bearing (4). Remove seal (2, 27 or 28). 9. Remove the base from th ...

  • Graco 215363 - page 8

    8 307043 Air Motor Service 13. Straighten the lockwires (L*) and remove them from the upper valve nuts (J*). Screw the upper valve nuts off. Remove the trip rod yoke (O), actuator (V), and trip rod (C). 14. Unscrew the bottom valve nuts (K*), and remove the poppets (N*). Make sure the valve bar spring clips (W) are not worn or damaged and that they ...

  • Graco 215363 - page 9

    9 307043 Air Motor Service 6. Install the toggle pins (Z) in the yoke (O). As- semble the toggle assembly (U) by placing a well greased spring onto the toggle arm (T) and then the toggle rocker (S). Place the toggle arm (T) ends of the toggle assembly (U) onto the toggle pins, and snap the pivot pin (S) ends of the toggle assembly into the lugs (P) ...

  • Graco 215363 - page 10

    6 *12 13 9* 10* 11 n 31 n 14 *15 2 21 20 5 18 32 34 33 05704 n 3 n 7 25 24* 8* 9* 1 22 30 4 23* 17 19 Y 36 35 28 29 n 27 NOTE: Seal lips face upward 26 10 307043 Parts HINGED CLAMP MOUNTING: SANIT AR Y Model 207546, Series H, Air Motor Assembly Includes items 1–36 ...

  • Graco 215363 - page 11

    11 307043 Parts HINGED CLAMP MOUNTING: SANIT AR Y Model 207546, Series H , Air Motor Assembly Includes items 1–36 Ref. No. Part No. Description Qty . Ref. No. Part No. Description Qty . 1 1 14422 SCREW , phillips hd mach; no. 8–32 x 0.375 in. (10 mm) long. 8 2 101578 SCREW , hex head; 5/16 x 0.875 in. (10 mm) long 6 3 n 156698 O-RING; buna-N 1 ...

  • Graco 215363 - page 12

    05705B 10 *16 17 13* 14* 15 n 30 n 18 20 24 25 9 21 31 33 32 n 7 n 11 29 28* 12* 13* 1 Y 37 *19 8 27* 23 26 35 34 NOTE: Seal lips face upward 3 4 n 2 5 36 6 12 307043 Parts ST ANCHION TUBE MOUNTING Model 206955, Series K, Air Motor Assembly Includes items 1–37 ...

  • Graco 215363 - page 13

    13 307043 Parts ST ANCHION TUBE MOUNTING Model 206955, Series K, Air Motor Assembly Includes items 1–37 Ref. No. Part No. Description Qty . Ref. No. Part No. Description Qty . 1 1 14422 SCREW , phillips hd mach; no. 8–32 x 0.38 in. (10 mm) long. 16 2 n 16H224 SEAL 1 3 101525 RING, retainer 1 4 101526 BEARING 1 5 101578 SCREW , hex head; 5/16 x ...

  • Graco 215363 - page 14

    05706B n 7 *12 13 9* 10* 11 n 31 n 14 *15 3 46,18 36 6 22, 37 32 34 33 n 4 n 19 26 25* 8* 9* 1 Y 43 5 24* 17 23 40 39 29 30 n 28 NOTE: Seal lips face upward 27 21 20, 38, 44 2 14 307043 Parts Model 205997, Series K Air Motor Assembly Includes: 1, 3–19, 23, 25–34, 36–43 Model 215363, Series D Air Motor Assembly Includes: 1, 3–19, 21, 23, 25? ...

  • Graco 215363 - page 15

    15 307043 Parts Model 205997, Series K Air Motor Assembly Includes: 1, 3–19, 23, 25–34, 36–43 Model 215363, Series D Air Motor Assembly Includes: 1, 3–19, 21, 23, 25–34, 37–43 Model 222791, Series D Air Motor Assembly Includes: 1–23, 25–34, 39–43 Ref. No. Part No. Description Qty . Ref. No. Part No. Description Qty . 1 1 14422 SCR ...

  • Graco 215363 - page 16

    16 307043 Accessories BLEED-TYPE MASTER AIR V AL VE (REQUIRED) 300 psi (21 bar , 2.1 MPa) Maximum Working Pressure Relieves air trapped in the air line between the pump air inlet and this valve when closed. 107141 3/4 npt (m x f) inlet and outlet 107142 1/2 npt (m x f) inlet and outlet SILENCER KIT 215354 Fits Monark Air Motors Models 206955, 22299 ...

  • Graco 215363 - page 17

    17 307043 Dimensional Drawings 05709 1 1.75 in. (298.4 mm) 13.25 in. (336.6 mm) 15.75 in. (400.1 mm) for 206955 5.75 in. (146.1 mm) Mounting Hole Layouts Three 0.34 in. (8.6 mm) diameter holes on 6.38 in. (162.1 mm) bolt circle 3 T ie Rod Pumps 05707 05708 45_ 45_ 2.5 in. (64 mm) 2.5 in. (64 mm) 4 in. (102 mm) 1 in. (25 mm) radius 161322 gasket 5 i ...

  • Graco 215363 - page 18

    18 307043 Graco Standard W arranty Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from de fec ts in material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, e xtended, or limited warranty published by Graco, Graco will, ...

メーカー Graco カテゴリー Outboard Motor

Graco 215363のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 215363の取扱説明書
- Gracoの製品カード
- パンフレット
- またはGraco 215363の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Graco 215363の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Graco 215363の取り付け説明書、サービスマニュアル、簡易説明書、またはGraco 215363のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Graco 215363の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Graco 215363デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがGraco 215363を使用するのを助ける技術的文書のことです。説明書は通常、全てのGraco 215363ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Gracoの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Graco 215363の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははGraco 215363の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Graco 215363に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Graco 215363デバイスの基本機能を使うにあたってのヒント。 Graco 215363のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Graco 215363に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるGraco 215363のメーカー/サービスへの連絡先に関する情報。

Graco 215363についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもGraco 215363の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがGraco 215363で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)