日本語 dropdown-ico

Calibre UK ICA93LVの取扱説明書

27ページ 0.11 mb
ダウンロード

ページに移動 of 27

Summary
  • Calibre UK ICA93LV - page 1

    Revision 1.7 09/12/1999 ICA93LV I 2 C Communications A dapter User Ma nual Contents 1. Introduction 1 1.1. Pack ing List 1 2. Configuring the Adapter 2 2.1. Setting the Adapter Base Addres s 2 2.2. W ait State Generator 2 2.3. Interrupt Generation 3 2.4. Bus T erm ination and Protection 3 2.5. Installing the Adapter 3 3. Connecting the Adapter to y ...

  • Calibre UK ICA93LV - page 2

    Revision 1.7 Page 1 of 27 09/12/1999 1. Introduction The I 2 C Com m unications Adapter is a half length PC inter face c ard des igned to fit any IBM PC com patible expansion slot. Based on the Philips PCF8584 bus controller, it f eatures full I 2 C bi-direc tional com patibility as either a m aster or slave. I 2 C connections are m ade via a 9 w a ...

  • Calibre UK ICA93LV - page 3

    Revision 1.7 Page 2 of 27 09/12/1999 2. Configuring the A dapter NOTE: MANY COM PONENT S ON THE ADA PTER CARD A RE STATIC SENSIT IVE. OBSERVE NORM AL STA TIC SENSIT IVE PRECA UTIO NS WHEN HANDLING THE CA RD! The adapter is supplied in a s tandard configuration which should suit most applications. Howev er, some features are link selectable. Read th ...

  • Calibre UK ICA93LV - page 4

    Revision 1.7 Page 3 of 27 09/12/1999 Important Note: Due to the internal operation of the ICA93, it must not be accessed o ver the PC bus (read or w ritten ) more than o nce every nine of it s ow n clock cycles. The ICA93 is clocked at 12MHz ; therefore it MU ST NOT be accessed more than once ev ery 0.75 microseconds. If this requirement is not obs ...

  • Calibre UK ICA93LV - page 5

    Revision 1.7 Page 4 of 27 09/12/1999 3. Conn ecting th e A dapter to your System 3.1. Connec tor Pinout All external connec tions are m ade via a 9 way “D” sock et: Pin Norm al Mode 10 V 20 V 30 V 40 V 5N C 6 SDA (Bi-direc tional) 7 +V Variable bus voltage 8 SCL (Bi-direc tional) 9N C NOTE: THE PINS M A RKED NC MUST NOT BE CONNECT ED IN NORM A ...

  • Calibre UK ICA93LV - page 6

    Revision 1.7 Page 5 of 27 09/12/1999 4. Getting Started 4.1. Resetting t he A dapter A reset forces the adapter into a well defined state, ready for initialisation. T he card uses the sam e reset line as the PC so either a power up or hard rese t (press the <RESET> button on your PC) will suff ice. 4.2. Introduction to the Utilities The utili ...

  • Calibre UK ICA93LV - page 7

    Revision 1.7 Page 6 of 27 09/12/1999 5. Using the Utilities Each utility is documented in a s tandard for m at, which lists its nam e, us age, function, and ef fect on the adapter is given. Following a reset, the adapter should be setup prior to any data transf er. 5.1. C Routines 5.1.1. I 2 C Setup/Initialisation Routine Name: setup(base, own, sc ...

  • Calibre UK ICA93LV - page 8

    Revision 1.7 Page 7 of 27 09/12/1999 Parameters are: int controladdress address of I 2 C control r egister. T his is equal to 1+( base address of adapter s et by links on circuit boar d). Value Returned: int <status> where status is an integer fr om 0x 00 to 0xFF which indic ates the curr ent status of I 2 C Com munications Adapter . See Appe ...

  • Calibre UK ICA93LV - page 9

    Revision 1.7 Page 8 of 27 09/12/1999 { int base, slv, setnac k; base = 0x310; /* Adapter’s bas address = 0x 310 (hex) */ slv = 0xa0; /* I 2 C Address of s lave, this is a typical */ /* write for an I 2 C st atic RAM or EEPROM */ setnack = 0; /* Enable Ack nowledge (see param eter */ /* descriptions ) */ sendaddress (base, slv, s etnack) ; printf( ...

  • Calibre UK ICA93LV - page 10

    Revision 1.7 Page 9 of 27 09/12/1999 /* This will read a by te of data fr om a slave previously addressed */ /* by and with acknowledge already disabled by sendaddress. */ /* After r eading the data, ack nowledge will be re-enabled. */ 5.1.5. Write Data Byte to Slav e Routine Name: writeby te(base, data) Usage: writeby te(base, data) Function: proc ...

  • Calibre UK ICA93LV - page 11

    Revision 1.7 Page 10 of 27 09/12/1999 #include <dos.h> /* Optional, but rec omm ended if your compiler */ /* supports DO S I/0 functions */ #include <i2c.h> /* This Contains the I 2 C routines */ mai n { int base, controladdr ess; base = 0x310; /* Adapter’s base addr ess = 0x 310 (hex) */ controladdres s = base + 1; /* Control Registe ...

  • Calibre UK ICA93LV - page 12

    Revision 1.7 Page 11 of 27 09/12/1999 Name: setup (baseaddr%, own%, sc lk%) Usage: call setup(bas eaddr%, own%, sclk %) Function: procedure to s et up I 2 C Comm unic ations Adapter. Parameters are: baseaddr% base address of adapter s et by links on circuit board. own% I 2 C address to which the adapter is to respond in slave m ode. T his form s th ...

  • Calibre UK ICA93LV - page 13

    Revision 1.7 Page 12 of 27 09/12/1999 baseaddr% = &h310 ‘* adapter’s base addr ess = 0x310 ( hex) * controladdres s% = baseaddr % + 1 status% = FNgets tatus%(contr oladdress%) print”I 2 C Com m unications Adapter Status = “;status % ‘* This will read the I 2 C Comm unic ations Adapter’s c urrent status * 5.2.3. I 2 C A ddress and St ...

  • Calibre UK ICA93LV - page 14

    Revision 1.7 Page 13 of 27 09/12/1999 setnack % this controls whether the I 2 C Com munic ations Adapter trans m its and Ack nowledge down the I 2 C Bus on reception of a byte. The last byte received during a transf er m ust not be ac knowledged, in all other c ases ack nowledge mu st be enabled. If setnac k% = 0 then ac knowledge is enabled, if s ...

  • Calibre UK ICA93LV - page 15

    Revision 1.7 Page 14 of 27 09/12/1999 Function: procedure to send a Stop (end of c omm unica tion signal) down the I 2 C Bus, ending a transm ission or reception with a slave that was address previously by sendaddress . Parameters are: controladdres s% The addres s of the I 2 C Com m unications Adapter control register , equal to 1+(base addres s s ...

  • Calibre UK ICA93LV - page 16

    Revision 1.7 Page 15 of 27 09/12/1999 slv% = &ha1 ‘* I 2 C Address of slave, this is a ty pical read addres s * ‘* for an I 2 C s tatic RAM or EEPROM* setnack % = 0 ‘* Enable Ack nowledge (see param eter desc riptions) * call restar t(baseaddr%, s lv%, setnack %) print”Restar t and I 2 C Slave Address s ent” ‘* This will send a Rest ...

  • Calibre UK ICA93LV - page 17

    Revision 1.7 Page 16 of 27 09/12/1999 baseaddress is the addres s at which the adapter has been ins talled, e.g. 310H ownaddress I2C address to which the adapter is to res pond in slave mode. T his f orm s the upper 7 bits of the 8 bit addres s, the lowest bit being the read (1) or write (0) bit. Th is m eans that if ownaddres s = 57H the card will ...

  • Calibre UK ICA93LV - page 18

    Revision 1.7 Page 17 of 27 09/12/1999 Setnack 1 for no ac knowledge 0 for ack nowledge. Paramete rs returned I 2 Cdata, the data read, if a time-out oc curs the Er rCode 8005H is returned. Prerequisites Adapter m ust be conf igured using setup, start and read addr ess sent by sendaddress. Functional Desc ription If setnack is 1 the function writes ...

  • Calibre UK ICA93LV - page 19

    Revision 1.7 Page 18 of 27 09/12/1999 getstatus Function spec ification: Int getstatus ( ) Paramete rs returned I 2 Cstatus, the current value of the bus status . Prerequisites Adapter mus t be configur ed using setup. Functional desc ription The f unction reads status word f rom the adapter and returns it. recover Function spec ification: Int reco ...

  • Calibre UK ICA93LV - page 20

    Revision 1.7 Page 19 of 27 09/12/1999 W hen all the by tes have been transm itted a stop is issued and the total number of bytes is returned. Sendby tes can only be used in mas ter write m ode. getbyte s Function spec ification Int getby tes (int far *transfer array) The f ar pointer m ust point to a s ingle dimens ional array the form at of which ...

  • Calibre UK ICA93LV - page 21

    Revision 1.7 Page 20 of 27 09/12/1999 Getbytes can only be used in m aster read m ode. slavelastbyte Function spec ification void slavelastbyte( ) Paramete rs returned none. Prerequisites Adapter mus t be configur ed using set up. T his func tion would norm ally only be called following the end of a transm ission in slave write mode – when the ad ...

  • Calibre UK ICA93LV - page 22

    Revision 1.7 Page 21 of 27 09/12/1999 6. Furth er Informatio n The f ollowing references m ay be found usef ul when using the adapter: Philips Semic onductor s Tec hnic al Handbook Book 4 Parts 12a and 12b. T hese give details of the I2C com patible ICs, and the I 2 C Bus specific ation. The PCF 8584P used on the adapter is included in later editio ...

  • Calibre UK ICA93LV - page 23

    Revision 1.7 Page 22 of 27 09/12/1999 7. T he Real-Time Bu s Mo nitor The pr ogram REALTIM1.EX E in the MONTO R director y is a completely non-invasive real-tim e bus monitor which records ac tivity on an I 2 C-bus , post-proc esses the data and s tores the res ults in an ASCII file. This file can be printed out or exam ined w ith a word-process or ...

  • Calibre UK ICA93LV - page 24

    Revision 1.7 Page 23 of 27 09/12/1999 A ppendix A I 2 C Communications A dapter S tatus Codes This is an eight bit register, read using the gets tatus routine. Eac h individual bit has its own m eaning as follows: Bit 7 (MSB) - The PIN Bit The PIN bit “Pending Inter rupt Not” is a read- only flag which is us ed to s ynchronize serial co m m uni ...

  • Calibre UK ICA93LV - page 25

    Revision 1.7 Page 24 of 27 09/12/1999 A ppendix B – I 2 C Communications A dapter Control Codes The Control Regis ter should norm ally be w ritten using the setup, s endaddress and s endstop routines. T o implem ent m ore advanc ed func tions such as enabling hardware interrupt gener ation or im plementing long distance mode, thes e routines m ay ...

  • Calibre UK ICA93LV - page 26

    Revision 1.7 Page 25 of 27 09/12/1999 A ppendix C - T he M ost Commonly A sked I 2 C Questio ns General Que stions Question Will my adapter work in a Pentium PC? Answer Y es and there is no need to alter LK 4 f rom the position in which your adapter was shipped. Question Will my adapter run I2C clock speeds greater than 90KHz? Answer At the mom ent ...

  • Calibre UK ICA93LV - page 27

    Revision 1.7 Page 26 of 27 09/12/1999 W indows 95 START - Run regedit HKEY_LOCAL_MACHINE | |--S YS TEM | |--CurrentControlSet | |--S ervi ces | |--Cl ass | |--W inRT | |--W inRTdev0 | |--Parameter s |--Section0 |--Section1 W indows NT ST ART - Run r egedit HKEY_LOCAL_MACHINE | |--S YS TEM | |--CurrentControlSet | |--S ervi ces | |--W inRT | |--W in ...

メーカー Calibre UK カテゴリー Network Card

Calibre UK ICA93LVのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- ICA93LVの取扱説明書
- Calibre UKの製品カード
- パンフレット
- またはCalibre UK ICA93LVの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Calibre UK ICA93LVの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Calibre UK ICA93LVの取り付け説明書、サービスマニュアル、簡易説明書、またはCalibre UK ICA93LVのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Calibre UK ICA93LVの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Calibre UK ICA93LVデバイスの取扱説明書はどのようなものですか？
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがCalibre UK ICA93LVを使用するのを助ける技術的文書のことです。説明書は通常、全てのCalibre UK ICA93LVユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Calibre UKの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Calibre UK ICA93LVの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははCalibre UK ICA93LVの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Calibre UK ICA93LVに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Calibre UK ICA93LVデバイスの基本機能を使うにあたってのヒント。 Calibre UK ICA93LVのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Calibre UK ICA93LVに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるCalibre UK ICA93LVのメーカー/サービスへの連絡先に関する情報。

Calibre UK ICA93LVについてご質問がありますか？

次のフォームを使用してください

見つけた説明書を読んでもCalibre UK ICA93LVの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがCalibre UK ICA93LVで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

Captcha
新しい画像

コメント (0)