Grindmaster P400ESHPの取扱説明書

36ページ 2.17 mb
ダウンロード

ページに移動 of 36

Summary
  • Grindmaster P400ESHP - page 1

    Shuttle Brewer & Airpot/Shuttle Brew ers Operation and Instruction Man u al For Models P300E, P400E, P400ESHP , RAP300E, RAP400E, RAPS300E, RAPS400E Inst allation: See rough-in drawings in this manual for di men sions and lo ca tions of electric and water input. Set-Up/Position 1) Remove the brewer from the packing material and att ach its legs ...

  • Grindmaster P400ESHP - page 2

    Page 2 Shuttle Brewers & Airpot/Shuttle Brewers Inst allation (con't) Electric Hook-up 1) The electric ratings for your brewer are printed on its nameplate. T ypical electric ratings are: P300, P400, RAP300, RAP400 Optional 120/208V , 3.8kW , 18A or 120/240V 5.0kW , 21A, 1 phase S tandard 120/208V , 5.0kW , 24A or 120/240V 6.6kW , 28A, 1 p ...

  • Grindmaster P400ESHP - page 3

    Page 3 Shuttle Brewers & Airpot/Shuttle Brewers W arning Labels The following warning labels were on your dispenser when it was shipped from the factory . They should remain on your dispenser in good, readable condition at all times. If one of your labels is missing or damaged, order a replacement label immediately . Part # A546-445 Located on ...

  • Grindmaster P400ESHP - page 4

    Page 4 Shuttle Brewers & Airpot/Shuttle Brewers Operation 1) RAPS Brewers require the accessory warmer base placed over the pegs on the brew shelf before brewing into a shuttle. Plug the base into the receptacle on the side of the brewer . The recept acle is only energized when a shuttle is in place. 2) Place an empty , warm shuttle or airpot o ...

  • Grindmaster P400ESHP - page 5

    Page 5 Shuttle Brewers & Airpot/Shuttle Brewers Adjustment s All adjustable component s are located under the top cover . T o access these part s: 1) Shut off the electric line to the brewer or unplug the brewer . 2) Remove the single screw fastening the top cover . Remove the top cover . 3) Pull forward and lift of f the top cover . Brew V olu ...

  • Grindmaster P400ESHP - page 6

    Page 6 Shuttle Brewers & Airpot/Shuttle Brewers T wo Batch Timer with Knob Adjustment, See Figure 2: This timer is adjustable from 15 seconds to 5 minutes. Locate the adjustment knobs under the top cover . Set this timer by adjusting the knob. The batch selector switch picks the adjustment potentiometer which the timer will see. Figure 2 T wo B ...

  • Grindmaster P400ESHP - page 7

    Page 7 Shuttle Brewers & Airpot/Shuttle Brewers T o Adjust the Byp ass: 1) Shut off and open brewer as described at the beginning of the adjustment s section. 2) Locate the bypass valve for the brew head you wish to adjust. V alve is on the right and front of the BREW valve. 3) Open the valve (counter clockwise) to the desired setting. Use the ...

  • Grindmaster P400ESHP - page 8

    Page 8 Shuttle Brewers & Airpot/Shuttle Brewers 4) If the maximum temperature adjustment needs to be increased, insert a small flat screwdriver into the shaft. T urn the calibration screw counter clockwise to increase the maximum temperature. Optional Solid S tate Thermostat: This control maint ains temperature within 3°F . The ad just able ra ...

  • Grindmaster P400ESHP - page 9

    Page 9 Shuttle Brewers & Airpot/Shuttle Brewers Cleaning Af ter Each Brew: 1) Dispose of grounds and rinse brew basket. 2) Rinse shuttle or airpot containers before reuse. Every Day: 1) W ash brew basket with warm soapy water . The wire basket is removable to aid cleaning. 2) Remove spray head(s), located above brew basket(s), using gloves or a ...

  • Grindmaster P400ESHP - page 10

    Page 10 Shuttle Brewers & Airpot/Shuttle Brewers Weekly or Bi-W eekly , Depending on Use 1) Fill shuttles with one gallon, 2/3 full, of hot water . 2) Pour into the shuttle liners the recommended concentration of urn cleaner (excessive amounts of cleaner will attack the st ainless steel). Urn cleaners that have been used successfully: DIP-IT , ...

  • Grindmaster P400ESHP - page 11

    Page 1 1 Shuttle Brewers & Airpot/Shuttle Brewers Service (con't) Drain W ater T ank Always empty the tank before shipping. Note: Brewer may cont ain over 5 gallons of hot water . 1) Prepare a heat resist ant container to drain t ank water into. 2) Shut off power to the brewer . 3) Remove the front access panel. 4) Pinch or clamp the silic ...

  • Grindmaster P400ESHP - page 12

    Page 12 Shuttle Brewers & Airpot/Shuttle Brewers T roubleshooting: Filling, Heating, and Brewing Overfilling water t ank even when power is off. Fill valve not sealing properly . Fill valve installed backwards. W ater entering tank continuously , usually slowly . Look for direction of arrow on valve body . Disassemble valve and clean out dirt. ...

  • Grindmaster P400ESHP - page 13

    Page 13 Shuttle Brewers & Airpot/Shuttle Brewers If you still need help, call our T echnical Service Department at (502) 425-4776 or (800) 695-4500 (USA & Canada only) Monday thru Friday 8 am - 8 pm EST or an authorized service center in your area. Please have the model and serial numbers ready so that accurate information can be given. Pri ...

  • Grindmaster P400ESHP - page 14

    Page 14 Shuttle Brewers & Airpot/Shuttle Brewers T roubleshooting: Filling, Heating, and Brewing Brewing Problems The brewing system consists of the following component s: • S tart and S top, switches located in the top control panel. • Brew T imer , located in the top control section under the top cover . • Brew V alve, located in the to ...

  • Grindmaster P400ESHP - page 15

    Page 15 Shuttle Brewers & Airpot/Shuttle Brewers Part s Illustration for Models P300E & P400E Item Part # Description Item Part # Description 1 A545-034 LEG , 4” PLASTIC W/ SS FOOT 13 A725-081 BRASS SPRA Y TEE W/ BYP ASS TUBING 1 A545-015 LEG , 4” SS (OPTIONAL) 14 A530-009 BREW TIMER 0-8 MINUTES 2 A537-043 HOT W A TER FAUCET W/ NUT 15 A ...

  • Grindmaster P400ESHP - page 16

    Page 16 Shuttle Brewers & Airpot/Shuttle Brewers Part s Illustration for Model P400ESHP Item Part # Description Item Part # Description 1 A545-034 LEG , 4” PLASTIC W/ SS FOOT 15 A585-021 SPRA Y TUBING 3/8” ID X 5/8”OD X 6”LG 1 A545-015 LEG , 4” SS (OPTIONAL) 16 A712-018 ELECTRODE ASSEMBL Y 2 A537-043 HOT W A TER FAUCET W/ NUT 17 A535- ...

  • Grindmaster P400ESHP - page 17

    Page 17 Shuttle Brewers & Airpot/Shuttle Brewers Part s Illustration for Model RAP400E Item Part # Description Item Part # Description 1 A548-072 LEG , RUBBER (RAP400) 11 A515016 PILOT LIGHT 1 A545-004 LEG , PLASTIC 4” (OPTIONAL RAP 400) 12 A725-082 SPRA Y TEE KIT W/ BYP ASS PLUG 1 A548-090 LEG , PLASTIC PLUG (RAP300) 13 A530-009 BREW TIMER 0 ...

  • Grindmaster P400ESHP - page 18

    Page 18 Shuttle Brewers & Airpot/Shuttle Brewers Part s Illustration for Model RAPS400E FRONT Item Part # Description Item Part # Description 1 A545-034 LEG , 4” PLASTIC W/ SS FOOT 16 A725-081 BRASS SPRA Y TEE W/ BYP ASS TUBING 1 A545-015 LEG , 4” SS (OPTIONAL) 17 A585-021 SPRA Y TUBING 3/8” ID X 5/8”OD X 6”LG 2 A537-043 HOT W A TER F ...

  • Grindmaster P400ESHP - page 19

    Page 19 Shuttle Brewers & Airpot/Shuttle Brewers Part s Illustration for Model VSB-400 Item Part # Description Item Part # Description 1 A545-034 LEG , 4” PLASTIC W/ SS FOOT 12 A725-081 SPRA Y TEE KIT W/ BYP ASS TUBING 1 A545-015 LEG , 4” SS (OPTIONAL) 13 A530-009 BREW TIMER 0-8 MINUTES 2 A531-035 TERMINAL BLOCK 14 A585-021 SILICONE TUBING ...

  • Grindmaster P400ESHP - page 20

    Page 20 Shuttle Brewers & Airpot/Shuttle Brewers Part s Illustration for Shuttle CS-LL Item Part # Description 1 A537-053 F AUCET MODEL ES 2 A522078 SHANK W/ CHROME BONNET 3 A718-018 GAUGE ASSEMBL Y 4 A725-092 KIT , SHUTTLE LID A713-027 SS SHUTTLE COVER (not shown)* 5 A548-142 LID RET AINING CLIP 6 A548-140 A61365 LID STOPPER W/ O-RING * S.S. C ...

  • Grindmaster P400ESHP - page 21

    Page 21 Shuttle Brewers & Airpot/Shuttle Brewers Rough-In Drawing for Model P-300 ...

  • Grindmaster P400ESHP - page 22

    Page 22 Shuttle Brewers & Airpot/Shuttle Brewers Rough-In Drawing for Model P-400 & P-400ESHP ...

  • Grindmaster P400ESHP - page 23

    Page 23 Shuttle Brewers & Airpot/Shuttle Brewers Rough-In Drawing for Model RAP-300 ...

  • Grindmaster P400ESHP - page 24

    Page 24 Shuttle Brewers & Airpot/Shuttle Brewers Rough-In Drawing for Model RAP-400 ...

  • Grindmaster P400ESHP - page 25

    Page 25 Shuttle Brewers & Airpot/Shuttle Brewers Rough-In Drawing for Model RAPS-300 ...

  • Grindmaster P400ESHP - page 26

    Page 26 Shuttle Brewers & Airpot/Shuttle Brewers Rough-In Drawing for Model RAPS-400 ...

  • Grindmaster P400ESHP - page 27

    Page 27 Shuttle Brewers & Airpot/Shuttle Brewers Rough-In Drawing for Model VSB-300 W W W W W A TER IM S ...

  • Grindmaster P400ESHP - page 28

    Page 28 Shuttle Brewers & Airpot/Shuttle Brewers Rough-In Drawing for Model VSB-400 ...

  • Grindmaster P400ESHP - page 29

    Page 29 Shuttle Brewers & Airpot/Shuttle Brewers Wiring Diagram for P300E/P400E, with 1 Batch T imer NOTE: THIS DRA WING SHOWS COMPONENTS ON ST ANDARD MODEL ONL Y . SEE 091-548 FOR WIRING OF BREWER OPTIONS ...

  • Grindmaster P400ESHP - page 30

    Shuttle Brewers & Airpot/Shuttle Brewers Page 30 Wiring Diagram for P300E/P400E, with 2 Batch T imer NOTE: THIS DRA WING SHOWS COMPONENTS ON ST ANDARD MODEL ONL Y . SEE 091-548 FOR WIRING OF BREWER OPTIONS ...

  • Grindmaster P400ESHP - page 31

    Page 31 Shuttle Brewers & Airpot/Shuttle Brewers Wiring Diagram for RAP300E/400E NOTE: THIS DRA WING SHOWS COMPONENTS ON ST ANDARD MODEL ONL Y . SEE 091-548 FOR WIRING OF BREWER OPTIONS Drawing #091-545 ...

  • Grindmaster P400ESHP - page 32

    Page 32 Shuttle Brewers & Airpot/Shuttle Brewers Wiring Diagram for RAPS 300/400E NOTE: 1) TWO SETS OF RECEPT ACLE COMPONENTS ONL Y PROVIDED ON TWIN RAPS400E MODEL. DELETE GROUP I N DASHED BOX FOR RAPS300E. 2) THIS DIAGRAM SHOWS COMPONENTS ON ST AN - DARD MODEL ONL Y . SEE 091-548 FOR WIRING OF BREWER OPTIONS. Drawing #091-523 ...

  • Grindmaster P400ESHP - page 33

    Page 33 Shuttle Brewers & Airpot/Shuttle Brewers Wiring Diagram for P-400ESHP ...

  • Grindmaster P400ESHP - page 34

    Page 34 Shuttle Brewers & Airpot/Shuttle Brewers Wiring Diagram #091-548 NOTE: 1) ONE GROUP OF W ARMER COMPONENTS PER BREW HEAD ON P AND RAPS MODELS. 2) TRANSFORMER MUST BE USED WHEN NEUTRAL LINE IS NOT PROVIDED. 3) IF MODEL RAP , DELETE W ARMER COMPONENTS. 4) IF MODEL IS RAPS, DELETE WARMER LIGHT AND REPLACE W ARMER ELEMENT WITH NEMA 6-15 RE - ...

  • Grindmaster P400ESHP - page 35

    Page 35 Shuttle Brewers & Airpot/Shuttle Brewers Wiring Diagram #091-182 T3 T3 T3 1 1 T4 A T2 T3 T3 T4 T4 T4 B T2 T3 T3 1 1 T1 C T3 T3 T3 T1 T1 T4 D T2 T3 T3 T1 T1 T4 E T2 T3 T3 T1 T1 T2 F NOTE: USE WIRE NUT FOR 1 - 1 CONNECTION 5000 W A TT / 240V HEA TERS * SEP ARA TE 120V REQUIRED FOR CONTROLS (3 AMP LOAD) 2.0 KW - 120/208V - 1 PH - 3 WIRE - ...

  • Grindmaster P400ESHP - page 36

    Grindmaster® Coffee Grinders and Br ewers • PrecisionBr ew™ Brewing Systems • Espr essimo® Espresso Machines Crathco® Hot Beverage Dispensers • Crathco® Cold and Frozen Beverage Dispensers • AMW Cof fee and T ea Systems T el (502) 425-4776 • Fax (502) 425-4664 • 1-800-695-4500 (USA & Canada only) P .O. Box 35020 • Louisville ...

メーカー Grindmaster カテゴリー Hot Beverage Maker

Grindmaster P400ESHPのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- P400ESHPの取扱説明書
- Grindmasterの製品カード
- パンフレット
- またはGrindmaster P400ESHPの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Grindmaster P400ESHPの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Grindmaster P400ESHPの取り付け説明書、サービスマニュアル、簡易説明書、またはGrindmaster P400ESHPのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Grindmaster P400ESHPの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Grindmaster P400ESHPデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがGrindmaster P400ESHPを使用するのを助ける技術的文書のことです。説明書は通常、全てのGrindmaster P400ESHPユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Grindmasterの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Grindmaster P400ESHPの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははGrindmaster P400ESHPの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Grindmaster P400ESHPに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Grindmaster P400ESHPデバイスの基本機能を使うにあたってのヒント。 Grindmaster P400ESHPのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Grindmaster P400ESHPに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるGrindmaster P400ESHPのメーカー/サービスへの連絡先に関する情報。

Grindmaster P400ESHPについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもGrindmaster P400ESHPの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがGrindmaster P400ESHPで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)