Honeywell 6160EXの取扱説明書

18ページ 0.41 mb
ダウンロード

ページに移動 of 18

Summary
  • Honeywell 6160EX - page 1

    Galant 6160EX Keypad User Instructions Honeywell Security ...

  • Honeywell 6160EX - page 2

    Contents Glossary .....................................................................................3 Introduction ...............................................................................4 Day Mode, Full Setting and Unsetting .....................................5 Part And Night Setting .................................................... ...

  • Honeywell 6160EX - page 3

    Glossary The following terms will be used in this manual: Alarm: A panel detection circuit has been tripped. Cancel: The action of stopping an alarm condition. Keyfob: A remote control dev ice for setting and unsetting . Each fob will belong to a user. Keytag: A tag or card which can be used for setting and unsetting. Each tag will b elong to a use ...

  • Honeywell 6160EX - page 4

    Introduction Your Galant panel has various system functions, which can be accessed by one of three methods: • type a user code at a keypad • press a button on an RF keyfob or • present a keytag to a proximit y reader. The system can support up to 8 users. User 1 is as signed as the master user. Each user can have a user code (master user code ...

  • Honeywell 6160EX - page 5

    Day Mode, Full Setting and Unsetting Day mode is the normal m ode for the system. In this state the dis play will be simi lar to that shown on the right, wi th the time and date. Galant V2 21-01-02 09:54 Full Setting the Sy stem To full set the system (keypad) 1. Type your User Code. 2. Press 1 (FULL) A constant exit tone will sound. Open Zn:02 Exi ...

  • Honeywell 6160EX - page 6

    Unsetting the System from any Set State To unset the system (key pad) 1. Proceed to the keypad via the approved route. A pulsed tone will indicate that the entry timer is counting down. 2. Type in your User Code at the ke ypad before the expiry of the entry time. The tones will stop and the ke ypad will return to the Day Mode display. Galant V2 21- ...

  • Honeywell 6160EX - page 7

    Part And Night Setting It is possible to s et the s ystem but leave certa in detectors sw itched off. This is useful, fo r example, at nig ht while the b edrooms are occupi ed, or when leaving pets with in the pr emises. Your installer can set up these detectors. To Part set the s ystem, proceed exactly as for Full setting except instead o f pressi ...

  • Honeywell 6160EX - page 8

    Cancelling Alarms If an alarm activ ation is in progress, whether the system is set or unset, proceed directly to the keypad and type in your User Code. This will cancel the alarm condition and th e display will show the source of the alar m. T ypically, this will be the detection zone that caused the alarm condition. Intruder ZN:07 RF SUP. ZN:14 P ...

  • Honeywell 6160EX - page 9

    Viewing the Event Log The Galant alarm panel has an Event Log history that records every event which oc curs on the system. Th is includes setting, unsetting, alarm activations and fault conditions. To view the ev ent log: 1. Type in your User Code. 2. Press the # key then 0 (LOG). 3. The display w ill show the m ost recent ev ent on the system. 08 ...

  • Honeywell 6160EX - page 10

    Omitting Zones From the System. To allow flexibil ity, you can tem porarily disable i ndividual detection zones. This is called ‘Omitting’. Once a zone is omitted, it will be disabled for the duration of the next set period. When the panel is next unset, the zone will be enabled again. To Omit any zon e: 1. Type in your User Code. 2. Press 6 (O ...

  • Honeywell 6160EX - page 11

    Chime The Chime function allows you to set up a zone to cause a chim e tone to activate on the in ternal sounder and keypad, every time a particular zone is opened. This is particularly useful to warn if a door has b een opened. To set up a zone for Chime: 1. Type in your User Code. 2. Press 9 (CHIME). 3. Type in the zone number for the zone to b e ...

  • Honeywell 6160EX - page 12

    Adding and Removing Keyfo bs. The Keyfobs used on this system employ high security KEELOQ TM Rolling Code Encr yption to make them virtually i mpossible to duplicate. Adding Keyfobs With the system in DAY mode at the keypad: 1. Enter master user code, 8 (CODE), and user number (1-8). 2. Wait for double beep. Display says awaiting fob. 3. Press all ...

  • Honeywell 6160EX - page 13

    6. After second double b eep the card has been added successfully. Note: If at any time a triple bleep is heard, the learn procedure has failed. Removing Keytags Any keytag can be removed from the system as follows: 1. Enter master user code, 8 (CODE), and user number (1-8). 2. Wait a couple of seconds for a double beep. 3. Press *. A double beep c ...

  • Honeywell 6160EX - page 14

    User Descriptors Each user code o n the system can ha ve a 6-character tag assigned. This tag or descriptor makes it easy to identify users who accessed the system when viewing the event log. User descriptors are entered in a s imilar way to entering SMS tex t messages on mobile phones. To change th e descriptor for a particular user, 1. Type the M ...

  • Honeywell 6160EX - page 15

    Testing the System A test function is a vailable which allows a user to manual ly test the sensors and alarm sounders on the syst em. This test is carried out as follows: From normal Day mode; 1. Type in the user code. 2. Press 5 (Test) 3. The system will ring the outsid e bells for 5 seconds and switch on the strobe light. The strob e light will s ...

  • Honeywell 6160EX - page 16

    System Indications In addition to the displays shown previously, the following fau lt displays may appear on the k eypad. I f the fault cannot be rectified, please contact your installer, explaini ng the exact detail on the dis play. Keypad Display Meaning Tamper ZN: xx A tamper fault has occurred on the zone shown. Line Fail The telephone line has ...

  • Honeywell 6160EX - page 17

    Hotkeys Hotkeys are key com binations on the ke ypad that can cause an instant alarm condition. Both ke ys must be pressed sim ultaneously to activate the alarm. Hotkeys can be enable d or disabled b y your installer . The following Hotkey functions are available: Function Button Combination Panic Alarm # + * Assistance 1 + * Fire 3 + # Additional ...

  • Honeywell 6160EX - page 18

    Zone Information Zone Location Full Part Night 1 2 3 4 5 6 7 8 9 10 11 12 IU1-1233 Rev 1.3 18 ...

メーカー Honeywell カテゴリー Garage Door Opener

Honeywell 6160EXのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 6160EXの取扱説明書
- Honeywellの製品カード
- パンフレット
- またはHoneywell 6160EXの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Honeywell 6160EXの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Honeywell 6160EXの取り付け説明書、サービスマニュアル、簡易説明書、またはHoneywell 6160EXのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Honeywell 6160EXの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Honeywell 6160EXデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがHoneywell 6160EXを使用するのを助ける技術的文書のことです。説明書は通常、全てのHoneywell 6160EXユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Honeywellの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Honeywell 6160EXの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははHoneywell 6160EXの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Honeywell 6160EXに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Honeywell 6160EXデバイスの基本機能を使うにあたってのヒント。 Honeywell 6160EXのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Honeywell 6160EXに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるHoneywell 6160EXのメーカー/サービスへの連絡先に関する情報。

Honeywell 6160EXについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもHoneywell 6160EXの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがHoneywell 6160EXで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)