Husqvarna 225Eの取扱説明書

24ページ 0.62 mb
ダウンロード

ページに移動 of 24

Summary
  • Husqvarna 225E - page 1

    Operator ’ s manual (CARB, EP A) 101 89 19-95 225E Read through the Operator‘s manual carefully and understand the content before using the machine. US-1 225E Front 97-08-06, 10.37 1 ...

  • Husqvarna 225E - page 2

    2 – English Symbols • Warning! The blade continues to rotate even after the engine has stopped. When the engine has stopped, stop the blade from rotating by letting the blade come in contact with the ground. Indicates the direction of rotation. SYMBOL EXPLANA TION WARNING! The edger can be dangerous! Careless or incorrect use can result in seri ...

  • Husqvarna 225E - page 3

    English – 3 Before using a new machine • Read the Operator‘s Manual carefully. • Check the assembly and adjustment of the cutting equipment. See page 13. • Start the machine and check the carburetor settings. See page 16-17. IMPORTANT! A too lean carburetor adjustment significantly increases the risk of an engine breakdown. Insufficient c ...

  • Husqvarna 225E - page 4

    4 – English The machine‘s safety equipment This section describes the machine‘s safety equipment, its function and how checks and maintenance are carried out to ensure that it operates correctly. (See the chapter “What is what“ to locate where this equipment is positioned on your machine.) Personal protective equipment 3. Cutting attachme ...

  • Husqvarna 225E - page 5

    English – 5 5. Muffler The muffler is designed to give the lowest possible noise level and to direct the engine‘s exhaust fumes away from the operator. Muffler fitted with catalytic converter is also designed to reduce harmful exhaust components. In countries that have a warm and dry climate the risk of fire is obvious. We have therefore fitted ...

  • Husqvarna 225E - page 6

    6 – English 3. Cutting attachment guard • Ensure that the guard is undamaged and not cracked. • Replace the guard if it has been exposed to impact or is cracked. • Always use the prescribed blade an guard combination, see chapter "Technical data" . Control, maintenance and service of the machine‘s safety equipment IMPORTANT INFO ...

  • Husqvarna 225E - page 7

    English – 7 Two basic rules: 1) Only use the cutting and guard equipment we recommend! See chapter “Technical data“. 2) Check the cutting equip- ment with regard to damage and crack formation. Damaged cutting equipment should always be replaced. 7. Locking nut • Protect your hand from injury when assembling, use the blade guard as protectio ...

  • Husqvarna 225E - page 8

    8 – English Safety instructions before starting work • Inspect the working area. Remove loose objects such as stones, broken glass, nails, steel wire, string, etc. that can be thrown or become entangled in the blade or blade guard. • Keep unauthorised persons at a distance. Children, animals, onlookers and helpers should be outside the safety ...

  • Husqvarna 225E - page 9

    English – 9 Transport and storage • Store and transport the machine and fuel so that any leakage or fumes do not risk coming into contact with sparks or naked flames. For example, electric machines, electric motors, electrical switches/power switches, heaters or the like. • When storing and transporting fuel approved containers intended for t ...

  • Husqvarna 225E - page 10

    10 – English General working instructions Basic working techniques Basic safety precautions 1. Observe your surroundings: • To ensure that people, animals or other things cannot affect your control of the machine. • To ensure that the above mentioned do not come into contact with the cutting equipment or objects that can be thrown by the cutt ...

  • Husqvarna 225E - page 11

    English – 11 SAFETY INSTRUCTIONS Safety instructions after completing work • Ensure the blade has stopped before cleaning, carrying out repairs or an inspection. Remove the spark plug cable from the spark plug. • Wear heavy-duty gloves when carrying out repairs on the edger. • Store the machine out of reach of children. • Only use origina ...

  • Husqvarna 225E - page 12

    12 – English WHA T IS WHA T? 26 24 21 1 1 4 21 21 20 4 What is what on the edger? 1. Blade 2. Grease filler cap 3. Angle gear 4. Blade guard 5. Shaft 6. Loop handlebar 7. Throttle 8. Stop switch 9. Throttle trigger lock 10. Suspension for harness 11. Cylinder cover 12. Starter handle 13. Fuel tank 14. Choke 15. Air filter cover 16. Clutch cover 1 ...

  • Husqvarna 225E - page 13

    English – 13 Assembling the blade Fit the blade as follows: 1. Fit the drive disc (A) on the outgoing shaft. Make sure that the edge that fits in the hole of the blade is facing outward. 2. Block the blade rotation by inserting locking pin in the hole behind the blade guard engaging it in the corresponding hole in the drive disc. 3. Fit the blade ...

  • Husqvarna 225E - page 14

    14 – English NOTE! The edger is fitted with two-stroke engines and must always be run on a mixture of gasoline and two-stroke oil. To ensure the correct mixture proportions it is important to measure the quantity of oil accurately. When mixing small amounts of fuel small discrepancies in the amount of oil has a great bearing on the proportions of ...

  • Husqvarna 225E - page 15

    English – 15 Control before starting WARNING! When the engine starts with the choke lever in the choke or starter throttle position the cutting tool (blade or trimmer) starts to rotate immediately. ST ART AND ST OP For reasons of safety follow these recommendations! • Check that the support flange is not cracked due to fatigue or due to being t ...

  • Husqvarna 225E - page 16

    16 – English Basic setting • The carburetor is set to its basic setting when test run at the factory. The basic setting should be kept during the machine‘s first working hours. Thereafter the carburetor should be finely adjusted. Fine adjustment should be carried out by a skilled technician. NOTE! If the cutting attachment rotates/moves while ...

  • Husqvarna 225E - page 17

    English – 17 Correctly adjusted carburetor A correctly adjusted carburetor means that the machine accelerates without hesitation and the machine 4-cycles a little at max speed. Furthermore, the cutting attachment must not rotate/move at idling. A too lean adjusted low speed needle L may cause starting difficulties and bad acceleration. A too lean ...

  • Husqvarna 225E - page 18

    18 – English A muffler fitted with a catalytic converter reduces the extent of the following substances in the exhaust fumes: • Hydrocarbons (HC). Some hydrocarbons in gasoline and the exhaust are carcinogenic. • Nitric oxides (NO). Irritating for the breathing air-ways. • Aldehydes. The most common formaldehyde, is carcinogenic and causes ...

  • Husqvarna 225E - page 19

    English – 19 Lubricating the flexible drive axle Adjusting the edger‘s cutting depth MAINTENANCE Spark plug The condition of the spark plug is affected by: • An incorrect carburetor setting. • An incorrect fuel mixture (too much or faulty oil). • A dirty air filter. These factors cause deposits on the spark plug electrode that may result ...

  • Husqvarna 225E - page 20

    20 – English NOTE: Use only HUSQVARNA replacement parts. Use of other brands of replacement parts can cause damage to your unit or injury to the operator or others. Your warranty does not cover damage or liability caused by the use of accessories and/or attachments not specifically recommended by HUSQVARNA. Maintenance schedule Below you will fin ...

  • Husqvarna 225E - page 21

    English – 21 TECHNICAL DA T A T echnical data Engine Cylinder capacity, cu. in/cm 3 Cylinder bore, inch/mm Stroke length, inch/mm Recommended max. speed, rpm Max. speed, should not be exceeded, rpm Idling speed, rpm Speed of output axle, rpm Max. engine output, acc. to ISO 8893 Ignition system Manufacturer/type of ignition system Spark plug Elect ...

  • Husqvarna 225E - page 22

    22 – English YOUR W ARRANTY RIGHTS AND OBLIGA TIONS The EPA (U.S. Environmental Protection Agency), Carb (California Air Resources Board) and Husqvarna Forest & Garden are pleased to explain the emissions control system warranty on your 1997 and later Lawn and Garden Equipment Engine. In U.S., new utility and lawn and garden equipment engines ...

  • Husqvarna 225E - page 23

    English – 23 NOTES ...

  • Husqvarna 225E - page 24

    24 – English ´*2{•¶5$¨ ...

メーカー Husqvarna カテゴリー Trimmer

Husqvarna 225Eのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 225Eの取扱説明書
- Husqvarnaの製品カード
- パンフレット
- またはHusqvarna 225Eの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Husqvarna 225Eの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Husqvarna 225Eの取り付け説明書、サービスマニュアル、簡易説明書、またはHusqvarna 225Eのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Husqvarna 225Eの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Husqvarna 225Eデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがHusqvarna 225Eを使用するのを助ける技術的文書のことです。説明書は通常、全てのHusqvarna 225Eユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Husqvarnaの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Husqvarna 225Eの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははHusqvarna 225Eの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Husqvarna 225Eに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Husqvarna 225Eデバイスの基本機能を使うにあたってのヒント。 Husqvarna 225Eのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Husqvarna 225Eに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるHusqvarna 225Eのメーカー/サービスへの連絡先に関する情報。

Husqvarna 225Eについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもHusqvarna 225Eの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがHusqvarna 225Eで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)