Echo SRM - 2100SBの取扱説明書

36ページ 0.6 mb
ダウンロード

ページに移動 of 36

Summary
  • Echo SRM - 2100SB - page 1

    Grass T rimmer/Brush Cutter Operator's Manual MODELS, T ype 1E SRM - 2100SB Serial Number 001001 & Up SRM - 2400SB Serial Number 563000 & Up W ARNING DANGER Read rules for safe operation and instructions carefully. ECHO provides an Operator's Manual and a Safety Manual. Both must be read and understood for proper and safe operatio ...

  • Echo SRM - 2100SB - page 2

    2 I NTRODUCTION Welcome to the ECHO family. This ECHO product was designed and manufactured to provide long life and on-the-job- dependability. Read and understand this manual and the SAFETY MANUAL you found in the same package. You will find both easy to use and full of helpful operating tips and SAFETY messages. W ARNING DANGER Read rules for saf ...

  • Echo SRM - 2100SB - page 3

    G RASS T RIMMER /B RUSH C UTTER O PERA TOR ' S M ANUAL 3 This symbol accompanied by the words WARNING and DANGER calls attention to an act or condition that can lead to serious personal injury to operator and bystanders. The circle with the slash symbol means whatever is shown within the circle is prohibited. COUPLER M ANUAL S AFETY S YMBOLS A ...

  • Echo SRM - 2100SB - page 4

    4 Shaft Decal W ARNING DANGER • This unit can be dangerous and cause serious injury if improperly used. To reduce injury risk to operator, helpers and bystanders, read and understand the Operator's and Safety manuals. • Blindness can occur from objects that are thrown or ricocheted even with shield in place. Operators, helpers and bystande ...

  • Echo SRM - 2100SB - page 5

    G RASS T RIMMER /B RUSH C UTTER O PERA TOR ' S M ANUAL 5 Hot Surface Carburetor adjustment - Idle speed Carburetor adjustment - High speed mixture Symbol description/application Symbol form/shape Read and understand Operator's Manual. Wear eyes, ears and head protection Emergency stop Fuel and oil mixture Finger Severing Carburetor adjust ...

  • Echo SRM - 2100SB - page 6

    6 FUEL W ARNING DANGER Fuel is VERY flammable. Use extreme care when mixing, storing or handling or serious personal injury may result. • Use an approved fuel container. • DO NOT smoke near fuel. • DO NOT allow flames or sparks near fuel. • Fuel tanks/cans may be under pressure. Always loosen fuel caps slowly allowing pressure to equalize. ...

  • Echo SRM - 2100SB - page 7

    G RASS T RIMMER /B RUSH C UTTER O PERA TOR ' S M ANUAL 7 Eye Protection -- Wear eye protection that meets ANSI Z87.1 or CE requirements whenever you operate the trimmer. Hand Protection -- Wear no-slip, heavy duty work gloves to improve your grip on the Brush Cutter handles. Gloves also reduce the transmission of machine vibration to your hand ...

  • Echo SRM - 2100SB - page 8

    8 15M (50 ft.) SAFE OPERA TION Determine Operation Area - Provide all operators of this equipment with the operator's manual and instructions for safe operation. - Review the area to be trimmed. Look for hazards that could contribute to unsafe conditions. - Spectators and fellow workers must be warned, and children and animals prevented from c ...

  • Echo SRM - 2100SB - page 9

    G RASS T RIMMER /B RUSH C UTTER O PERA TOR ' S M ANUAL 9 EXTENDED OPERA TION / EXTREME CONDITIONS Vibration and Cold -- It is believed that a condition called Raynaud’s Phenomenon, which affects the fingers of certain individuals may be brought about by exposure to vibration and cold. Exposure to vibration and cold may cause tingling and bur ...

  • Echo SRM - 2100SB - page 10

    10 Ö Ö Ö Ö Ö Ö Ö Ö Ö Ö Ö Ö Ö Ö Ö Ö Ö Ö Ö MODELS SRM-2400SB SRM-2100SB Ö Ö Ö Ö Ö Ö Ö Ö Ö Ö Ö Ö Ö Ö Ö Ö Ö Ö Ö D ESCRIPTION The ECHO product you purchased has been factory pre-assembled for your convenience. Due to packaging restrictions, shield installation and other assembly may be necessary. After opening the c ...

  • Echo SRM - 2100SB - page 11

    G RASS T RIMMER /B RUSH C UTTER O PERA TOR ' S M ANUAL 11 EMISSION CONTROL Type 1E Models 1 2 3 5 6 7 8 9 10 11 12 13 23 4 14 15 16 17 18 19 20 21 22 The emission control system for this engine is EM (Engine Modification). Emission Control Label located on Engine (EXAMPLE ONLY, information on label varies by FAMILY). IMPORTANT ENGINE INFORMATI ...

  • Echo SRM - 2100SB - page 12

    12 1. OPERATOR'S MANUAL - Included in plastic bag (co-pack). Read before operation and keep in a safe place for future reference, i.e., operation, maintenance, storage and specifications. 2. SAFETY MANUAL - Included in plastic bag (co-pack). Read before operation to learn proper, safe operating techniques. Keep in a safe place for future refer ...

  • Echo SRM - 2100SB - page 13

    G RASS T RIMMER /B RUSH C UTTER O PERA TOR ' S M ANUAL 13 S PECIFICA TIONS * Install and use U-Handle when operating any model with blade. **The RPM range shown applies for all attachments. Refer to your attachment Operator's Manual "Specifications" section for proper RPM specifications. M OD E L S R M- 2100S B S R M - 2400S B S ...

  • Echo SRM - 2100SB - page 14

    14 A SSEMBL Y ECHO APPROVED OPTIONAL A TT ACHMENTS W ARNING DANGER Use only ECHO approved attachments for these models. Serious injury may result from the use of non approved attachment combinations. Read and comply with all safety instructions listed in this manual and attachment manual. ECHO, INC. will not be responsible for the failure of cuttin ...

  • Echo SRM - 2100SB - page 15

    G RASS T RIMMER /B RUSH C UTTER O PERA TOR ' S M ANUAL 15 POWER HEAD SHAFT / LOWER SHAFT ASSEMBL Y Tools Required: None Parts Required: Power Head Shaft, Lower Shaft Assembly 1 . Set Power Head/Shaft Assembly on a level surface. 2 . Loosen clamping knob (A). 3 . Pull locator pin (B) and rotate counter clockwise 1/4 turn to lock out position. 4 ...

  • Echo SRM - 2100SB - page 16

    16 NYLON LINE HEAD INST ALLA TION Tools Required: Head Locking Tool Parts Required: Nylon Line Head. 1 . Align locking hole in upper plate (B) with notch in edge of gear housing and insert head locking tool (A). 2 . Remove plastic sleeve from P.T.O. shaft (C). 3 . Be sure upper plate (B) remains on P.T.O. shaft. 4 . Thread line head onto P.T.O. sha ...

  • Echo SRM - 2100SB - page 17

    G RASS T RIMMER /B RUSH C UTTER O PERA TOR ' S M ANUAL 17 P RE - O PERA TION OPERA TION WITH BLADES Preparing the Trimmer/Brush Cutter for Blade Use WARNING DANGER Blade use DEMANDS specific Brush Cutter configuration. Operation without specified shield and harness can result in serious personal injury. Follow installation instructions include ...

  • Echo SRM - 2100SB - page 18

    18 8 Tooth Weed/Grass Blade P/N 69600120331 is designed for grass, garden debris and thick weeds. DO NOT use this blade for brush or heavy woody growth, 3/4" in. (19 mm) diameter or larger. Brush/Clearing Blade P/N 69500120331 is designed for cutting brush and woody growth up to 3" in. (76 mm) diameter. Use Shoulder/Waist Harness P/N 9994 ...

  • Echo SRM - 2100SB - page 19

    G RASS T RIMMER /B RUSH C UTTER O PERA TOR ' S M ANUAL 19 Handling Fuel -- W ARNING DANGER Fuel is VERY flammable. Use extreme care when mixing, storing or handling or serious personal injury may result. • Use an approved fuel container. • DO NOT smoke near fuel. • DO NOT allow flames or sparks near fuel. • Fuel tanks/cans may be under ...

  • Echo SRM - 2100SB - page 20

    20 IMPORTANT Stored fuel ages. Do not mix more fuel than you expect to use in thirty (30) days, ninety (90) days when a fuel stabilizer is added. IMPORTANT Stored two-stroke fuel may separate. ALWAYS shake fuel con- tainer thoroughly before each use. EQUIPMENT CHECK Before operation a complete check of the unit must be performed; • Check unit for ...

  • Echo SRM - 2100SB - page 21

    G RASS T RIMMER /B RUSH C UTTER O PERA TOR ' S M ANUAL 21 O PERA TION • Provide all operators of this equipment with the operator's manual and instructions for safe operation. • Before starting the unit, equip yourself and any other person working within the 15M (50 ft.) Safety Zone with the required Protective Equipment and clothing. ...

  • Echo SRM - 2100SB - page 22

    22 All Models The starting procedures is the same as Cold Start except DO NOT close the choke. W ARNING DANGER The cutting attachment should not rotate at idle. If cutting attach- ment moves, readjust carburetor according to "Carburetor Adjust- ment" instructions in this manual or see your ECHO Dealer, otherwise serious personal injury ma ...

  • Echo SRM - 2100SB - page 23

    G RASS T RIMMER /B RUSH C UTTER O PERA TOR ' S M ANUAL 23 3 . Start - Pull Rope. Lay the trimmer on a flat clear area and pull the recoil starter handle (D) until the engine fires. NOTE If engine does not start after 5 pulls, use Cold Start Procedure. STOPPING ENGINE 1 . Release Throttle. Allow engine to idle for a minute. 2 . Stop Switch - St ...

  • Echo SRM - 2100SB - page 24

    2 4 MAINTENANCE INTER V ALS / T N E N O P M O C M E T S Y S E C N A N E T N I A M E R U D E C O R P D ' Q E R L L I K S L E V E L R O Y L I A D E R O F E B E S U Y R E V E L E U F E R 3 S H T N O M 0 9 R O S R U O H 6 S H T N O M 0 7 2 R O S R U O H Y L R A E Y 0 0 6 S R U O H s e r u d e c o r P e c n a n e t n i a M r e l a e D o h c E d e d ...

  • Echo SRM - 2100SB - page 25

    G RASS T RIMMER /B RUSH C UTTER O PERA TOR ' S M ANUAL 25 AIR FIL TER Level 1. Tools required: Cleaning brush, 1" or 2" medium bristle paint brush. Parts required: SRM-2100SB 90008 REPOWER TM AIR & FUEL FILTER KIT. SRM-2400SB 90030 REPOWER TM AIR & FUEL FILTER KIT. 1 . Close choke (Cold Start Position). This prevents dirt fro ...

  • Echo SRM - 2100SB - page 26

    26 SP ARK PLUG Level 2. Tools required: Scrench (combination socket wrench and screwdriver), Feeler gauge (preferably a wire gauge) , Brush. Parts Required: Spark Plug, NGK BPMR-7A 1 . Remove spark plug and check for fouling, worn and rounded center electrode. 2 . Clean the plug or replace with a new one. DO NOT sand blast to clean. Remaining sand ...

  • Echo SRM - 2100SB - page 27

    G RASS T RIMMER /B RUSH C UTTER O PERA TOR ' S M ANUAL 27 3 . Use the wooden stick or brush to remove dirt form cylinder fins. IMPORTANT Do not use a metal scraper to remove dirt from the cylinder fins. 4 . Remove grass and leaves from the grid between the recoil starter and fuel tank. 5 . Assemble components in reverse order. NOTE When instal ...

  • Echo SRM - 2100SB - page 28

    28 CARBURETOR ADJUSTMENT SRM-2100SB Emission Models Level 2. Tools required: Screwdriver, Tachometer (ECHO P/N 99051130017) Parts required: None. NOTE Every unit is run at the factory and the carburetor is set in compli- ance with EPA Phase 1 and California Emission Regulations. In addition, the carburetor is equipped with HI and LO needle adjust- ...

  • Echo SRM - 2100SB - page 29

    G RASS T RIMMER /B RUSH C UTTER O PERA TOR ' S M ANUAL 29 CARBURETOR ADJUSTMENT SRM-2400SB Emission Models Level 2. Tools required: Screwdriver, Tachometer (ECHO P/N 99051130017). Parts required: None. NOTE Every unit is run at the factory and the carburetor is set in compli- ance with EPA Phase 1 and California Emission Regulations. This carb ...

  • Echo SRM - 2100SB - page 30

    30 Drive Shaft (Lower) IMPORTANT Lower and upper drive shaft must be lubricated with high tempera- ture automotive grease every 25 hours of operation, otherwise drive shaft assembly overheating and failure can result. 1 . Remove shield and gear housing as an assembly. a. Loosen two (2) screws (A) that clamp the gear housing to the drive shaft housi ...

  • Echo SRM - 2100SB - page 31

    G RASS T RIMMER /B RUSH C UTTER O PERA TOR ' S M ANUAL 31 2 . Use one piece of new nylon line (C) 12 m (40 ft.) long and thread through the molded loop (D) on the spool. Pull line tight and adjust so one end is 15 cm (6 in.) longer than the other. 3 . Hold the spool, opening toward you. Place index finger between the two strands and wind line, ...

  • Echo SRM - 2100SB - page 32

    32 SHARPENING MET AL BLADES Three styles of metal blades are approved for use on the ECHO Brush Cutter. The 8-tooth blade can be sharpened during normal maintenance. The clearing blade and 80 tooth blade require professional service. Before sharpening, CLOSELY inspect blade for cracks (look at the bottom of each tooth and the center mounting hole c ...

  • Echo SRM - 2100SB - page 33

    G RASS T RIMMER /B RUSH C UTTER O PERA TOR ' S M ANUAL 33 T ROUBLESHOOTING Probl em E n g i ne -- s tarts ha rd E n gin e - - does n ot st art Ca u s e Re me d y En gi n e Cr a n k s Fu el at car bu ret or No f u el a t car bu ret or Fu el st ra in er c l ogge d Fu el l in e cl ogged C arbu r et or Cl e a n Cl e a n S ee y ou r EC H O deal er ...

  • Echo SRM - 2100SB - page 34

    34 S TORAGE Long T erm Storage (over 30 days) Do not store your unit for a prolonged period of time (30 days or longer) without performing protective storage maintenance which includes the following: 1 . Store unit in a dry, dust free place, out of the reach of children. W ARNING DANGER Do not store in enclosure where fuel fumes may accumulate or r ...

  • Echo SRM - 2100SB - page 35

    G RASS T RIMMER /B RUSH C UTTER O PERA TOR ' S M ANUAL 35 NOTES ...

  • Echo SRM - 2100SB - page 36

    ECHO Incorporated 400 Oakwood Road Lake Zurich, IL 60047 Technical Publications Orders S ER VICING I NFORMA TION P ARTS Genuine ECHO Parts and ECHO REPOWER ™ Parts and Assemblies for your ECHO products are available only from an Authorized ECHO Dealer. When you do need to buy parts always have the Model Number and Serial Number of the unit with y ...

メーカー Echo カテゴリー Trimmer

Echo SRM - 2100SBのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- SRM - 2100SBの取扱説明書
- Echoの製品カード
- パンフレット
- またはEcho SRM - 2100SBの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Echo SRM - 2100SBの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Echo SRM - 2100SBの取り付け説明書、サービスマニュアル、簡易説明書、またはEcho SRM - 2100SBのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Echo SRM - 2100SBの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Echo SRM - 2100SBデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがEcho SRM - 2100SBを使用するのを助ける技術的文書のことです。説明書は通常、全てのEcho SRM - 2100SBユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Echoの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Echo SRM - 2100SBの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははEcho SRM - 2100SBの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Echo SRM - 2100SBに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Echo SRM - 2100SBデバイスの基本機能を使うにあたってのヒント。 Echo SRM - 2100SBのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Echo SRM - 2100SBに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるEcho SRM - 2100SBのメーカー/サービスへの連絡先に関する情報。

Echo SRM - 2100SBについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもEcho SRM - 2100SBの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがEcho SRM - 2100SBで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)