-
Napoleon Fireplaces OS10-3 - page 1
INSTALLER : THESE INSTRUCTIONS MUST BE CONVEYED TO AND REMAIN WITH THE HOMEOWNER. CERTIFIED IN CANADA TO CAN/CSA 22.2 #B40.0 - M87 &·R91 B140.1 & B140.3 CER TIFIED·IN THE UNITED ST A TES TO UL 896 -199 INSTALLATION AND OPERATION INSTRUCTIONS FOR OIL-FIRED CAST IRON STOVE MODEL OS10-3 WOLF STEEL LTD., RR#1, 24 NAPOLEON RD., BARRIE, ON., CA ...
-
Napoleon Fireplaces OS10-3 - page 2
INTRODUCTION Document n° 1092-1 EN ~ 04/02/2002 2 WARNING • The stove is an oil-fired stove. Do not burn wood or other materials in this stove. • Adults and especially children should be alerted to the hazards of high surface temperatures and should stay away to avoid burns or clothing ignition. Supervise young children when they are in the sa ...
-
Napoleon Fireplaces OS10-3 - page 3
NAPOLEON oil stoves are manufactured under the strict Standard of the World Recognized ISO9001 Quality Assurance Certificate. NAPOLEON products are designed with superior components and materials, assembled by trained craftsmen who take great pride in their work. The complete stove is thoroughly inspected by a qualified technician before packaging ...
-
Napoleon Fireplaces OS10-3 - page 4
General information Nominal heat output Oil consumption ** Chimney draft required Weight Flue outlet outside diameter max speed min speed max speed min speed 34.100 BTU/hr .31 US gal/hr .066 US gal/hr .072" w.c.g .032" w.c.g 260 lbs 5 inches 10 kW 1.20 litre/h 1/4 litre/h 18 Pa 8 Pa 118 kg 120-125-127 mm Connection to a L.VENT chimney Nom ...
-
Napoleon Fireplaces OS10-3 - page 5
Location and clearances If the stove is to be installed on a combustible floor, it must be installed on sheet metal or a tile. The oil drip tray, 72636 (not supplied) is a suitable substitute for either of these two pads. Maintain these minimum clearances to combustibles (fig. 2) : A 12 inches (300 mm) B 19 inches (483 mm) C 12 inches (300 mm) If r ...
-
Napoleon Fireplaces OS10-3 - page 6
THE TOT AL SMOKE PIPE LENGTH SHOULD NOT EXCEED 40% OF THE CHIMNEY HEIGHT ABOVE THE STOVE T O A MAXIMUM HORIZONT AL RUN OF 10 FEET . All smoke pipe must slope upwards at a minimum of 1/4" per foot (6 mm/0.3m) and all connections must be tight and secured by three sheet metal screws equally spaced. An uninsulated smoke pipe shall not pass throug ...
-
Napoleon Fireplaces OS10-3 - page 7
FINISHING Mounting flue collar The stove is supplied with a connection flue at rear. Smoke exit on top (figure 12, page 8) : - Remove the internal baffles on top (see page 11 ). - Fix the sealing rope in the groove on the top (2) and fit the flue spigot (1), ensuring there is a good seal. - Fix the sealing rope in the groove on the rear (2) and fit ...
-
Napoleon Fireplaces OS10-3 - page 8
The fuel system of this stove is designed to supply fuel by gravity pressure only. If the supply tank location is lower than the stove, it will be necessary to use the Napoleon SP32 suction pump. The SP32 should be installed a minimum of 12" above the stove carburetor and a minimum of 6" horizontally from the stove. This height difference ...
-
Napoleon Fireplaces OS10-3 - page 9
OPERATING INSTRUCTIONS Understanding your oil stove Furnace oil is fed from the tank to the burner floor ‘ A ’ where is it ignited by means of a firestarter. The heat produced by this flame brings the burner temperature to the required level to vaporize the fuel. Oil will only burn as a vapour not a liquid. Room combustion air enters the burner ...
-
Napoleon Fireplaces OS10-3 - page 10
Shut down 1. T urn the control knob to “0" setting. 2. Lift the safety lever . 3. T urn off the oil tank fuel supply valve. The oil tank fuel supply valve should always be shut off when the oil stove is not in operation. ADJUSTMENTS Oil flow adjustments The oil flow setting is done by the manufacturer and normally should not require any adju ...
-
Napoleon Fireplaces OS10-3 - page 11
MAINTENANCE Seasonal maintenance WEEKLY - DESCALE Push and pull the de-scaling lever in and out as well as turning slightly at the same time completely two or three times. Push in for normal burner operations or before relighting. EVERY 3 TO 4 MONTHS - CLEAN BURNER Remove all three catalyser components (C, D, E, figure 13 ). Remove any carbon resid ...
-
Napoleon Fireplaces OS10-3 - page 12
REPLACEMENTS Ordering replacement parts Contact your dealer or the factory for questions concerning prices and policies on replacement parts. Normally all parts can be ordered through your Napoleon dealer or distributor. When ordering replacement parts always give the following information: 1. Model & Serial number of fireplace 3. Part code 5. ...
-
Napoleon Fireplaces OS10-3 - page 13
Document n° 1092-1 EN ~ 04/02/2002 13 15 25 57 8 12 14 16 20 24 42 17 18 35 48 22 4 36 30 41 1 3 27 31 32 43 13 33 5 9 10 18 5 40 2 6 11 21 39 44 49 50 53 51 47 28 38 45 34 37 46 45 55 7 59 58 52 29 55 2 3 31 31 3 31 3 14 19 26 56 23 17 63 61 62 60 64 ...
-
Napoleon Fireplaces OS10-3 - page 14
Document n° 1092-1 EN ~ 04/02/2002 14 38 306273 77 . . Back wall ..................................c ........... 0 1 38 306273 76 . . Back wall ............................ B ................. 0 1 38 306273 79 . . Back wall ...................... A ......................0 1 38 306273 EF . . Back wall .......................................D ..... ...
-
Napoleon Fireplaces OS10-3 - page 15
Document n° 1092-1 EN ~ 04/02/2002 15 Notes ...
-
Napoleon Fireplaces OS10-3 - page 16
Document n° 1092-1 EN ~ 04/02/2002 16 SYMPTOM PROBLEM TEST SOLUTION Flames extinguish during lighting. Very cold chimney. No draft established - leave door ajar until fire has caught. - check air supply in the room Fire extinguishes once firestarter has burnt off. Fuel tank is empty - fill tank Fuel valve is closed. -open valve Main carburetor flo ...
Napoleon Fireplaces OS10-3についてご質問がありますか？
次のフォームを使用してください
見つけた説明書を読んでもNapoleon Fireplaces OS10-3の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがNapoleon Fireplaces OS10-3で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。