日本語 dropdown-ico

Vermont Casting 1655, 1656, 1657, 1658, 1659の取扱説明書

28ページ 0.96 mb
ダウンロード

ページに移動 of 28

Summary
  • Vermont Casting 1655, 1656, 1657, 1658, 1659 - page 1

    1 Vermont Castings Madison Homeowner ’ s Installation and Operating Manual For use in the United States and Canada SAFETY NOTICE: IF THIS APPLIANCE IS NOT PROPERLY INSTALLED, OPERATED AND MAINTAINED, A HOUSE FIRE MAY RESULT. TO REDUCE THE RISK OF FIRE, FOLLOW THE INSTALLATION INSTRUCTIONS. FAILURE TO FOLLOW INSTRUCTIONS MAY RESULT IN PROPERTY DAM ...

  • Vermont Casting 1655, 1656, 1657, 1658, 1659 - page 2

    2 Vermont Castings Madison Introduction Thank you for choosing a Vermont Castings Madison to meet your heating needs. We're confident you will find the Madison to be an effective woodburning heater incorporating modern, non-catalytic combustion technology with the classic aesthetic appeal of its Vermont Castings lineage. The Madison achieves h ...

  • Vermont Casting 1655, 1656, 1657, 1658, 1659 - page 3

    3 Vermont Castings Madison Specifications Madison, Model 1655 Series Maximum heat output ......................... 39,700 Btu’s/hr . 1 Area heated ...................................... Up to 1600 sq. ft. 2 Fuel size/type ...................................... 18” (46 cm) logs Loading ..................................................... Front ...

  • Vermont Casting 1655, 1656, 1657, 1658, 1659 - page 4

    4 Vermont Castings Madison Installation Chimneys Y our stove must be connected either to a sound masonry chimney that meets local codes, to a relined masonry chimney that meets local codes, or to an approved prefabricated metal chimney . Whichever of those types you use, the chimney and chimney con- nector must be in good condition and kept clean. ...

  • Vermont Casting 1655, 1656, 1657, 1658, 1659 - page 5

    5 Vermont Castings Madison Masonry Chimneys, cont'd. • Unused openings in an existing masonry chimney must be sealed with masonry to the thickness of the chimney wall, and the chimney liner should be repaired. Openings sealed with pie plates or wallpaper are a hazard and should be sealed with mortar or refractory cement. In the event of a ch ...

  • Vermont Casting 1655, 1656, 1657, 1658, 1659 - page 6

    6 Vermont Castings Madison Double-wall Chimney Connectors The Madison is approved for installation in the U.S. and Canada with double-wall chimney connectors that have been tested and listed for use with solid-fuel burning appliances by a recognized testing laboratory . Follow the instructions for assembling and install- ing double-wall connectors ...

  • Vermont Casting 1655, 1656, 1657, 1658, 1659 - page 7

    7 Vermont Castings Madison Connection Above the Fireplace In this installation, the chimney connector enters the fireplace flue through a thimble located above the fireplace. (Fig. 6) The liner of the fireplace chimney should extend at least to the point at which the chim- ney connector enters the chimney . Follow all the guidelines for installing ...

  • Vermont Casting 1655, 1656, 1657, 1658, 1659 - page 8

    8 Vermont Castings Madison Floor Protection A tremendous amount of heat radiates from the bottom plate of your Madison. The floor area directly under and around the stove will require protection from radiant heat as well as from stray sparks or embers that may escape the firebox. Heat protection is provided through the use of a V ermont Castings Bo ...

  • Vermont Casting 1655, 1656, 1657, 1658, 1659 - page 9

    9 Vermont Castings Madison To meet these requirements, a floor protector must be at least 54” (1372mm) wide (“A”,Fig. 12) and 52” (1320mm) deep (“B”, Fig. 12). Fireplace Hearth Protection Do not assume that your fireplace hearth is completely noncombustible. Many fireplace hearths do not satisfy the “completely noncombustible” requi ...

  • Vermont Casting 1655, 1656, 1657, 1658, 1659 - page 10

    10 Vermont Castings Madison Wall Shields W all shields should be constructed of 24 gauge or heavier sheet metal, or another noncombustible material such as 1/2" (13 mm) insulation board (Fig. 14) or common brick "laid on flat," with the 3 ¹⁄₂ " (90 mm) side down. Shields must be spaced out from the combustible surface 1&quo ...

  • Vermont Casting 1655, 1656, 1657, 1658, 1659 - page 11

    11 Vermont Castings Madison Alcove Installations Because of their restricted air flow and heat retention characteristics, specific construction requirements and special clearances apply to installations into alcoves. No stove or chimney connector heat shields are used in alcove installations. ALCOVE INSTALLATION OF THE MADISON IS NOT PERMITTED IN C ...

  • Vermont Casting 1655, 1656, 1657, 1658, 1659 - page 12

    12 Vermont Castings Madison Madison 1655 Series Clearance Chart Use the chart below together with the diagrams on the next page to determine the minimum clearance required for your particular installation. In any case, it is always advisable to locate the stove as far away from walls as pos- sible in order to take full advantage of the radiant prop ...

  • Vermont Casting 1655, 1656, 1657, 1658, 1659 - page 13

    13 Vermont Castings Madison F F C C A B D E J K L L G H P Q M N I I O O R R V W S T U U X X Stove Installed Parallel to Wall Stove in Corner Stove Installed Parallel to Wall Stove in Corner PROTECTED SURFACES Top Exit Installations, no heat shields Top Exit Installations, heat shield on stove, no shields on single-wall connector Top Exit Installati ...

  • Vermont Casting 1655, 1656, 1657, 1658, 1659 - page 14

    14 Vermont Castings Madison Stove Installed Parallel to Wall Stove in Corner Stove Installed Parallel to Wall Stove in Corner PROTECTED SURFACES Madison 1655 Series Clearance Diagram UNPROTECTED SURFACES Rear Exit Installations, Bottom Heat Shield, floor protection, minimum 18” (457mm) in front. Y Z AA BB EE FF CC DD N / A N / A Rear Exit Install ...

  • Vermont Casting 1655, 1656, 1657, 1658, 1659 - page 15

    15 Vermont Castings Madison Y ou will need the following tools to assemble the Madi- son: • 9/16" open end wrench • safety glasses & gloves • flat head screwdriver • power drill w/ 1/8" (3mm) bit • stub handle phillips screwdriver Unpack the Stove 1. Remove the shipping straps and plastic wrap. 2. Inspect the stove and conte ...

  • Vermont Casting 1655, 1656, 1657, 1658, 1659 - page 16

    16 Vermont Castings Madison Attach the Chimney Connector Insert the crimped end of the first section of chimney connector into the flue collar . Using the holes in the collar as guides, drill 1/8" (3mm) holes through the connector pipe. Use the three #10 x 1/2" sheet metal screws provided to secure the chimney connection to the flue colla ...

  • Vermont Casting 1655, 1656, 1657, 1658, 1659 - page 17

    17 Vermont Castings Madison Operation How the Madison Works Combustion control is achieved in the Madison through two separate air delivery systems. The primary air control lever , located at the left rear corner of the stove, controls the amount of incoming primary air for starting, maintaining, and reviving the fire. More air entering the stove m ...

  • Vermont Casting 1655, 1656, 1657, 1658, 1659 - page 18

    18 Vermont Castings Madison Fig. 27 Start a fire with small, dry kindling. ST263 Fig. 28 Gradually add larger pieces of wood until all the wood is burning well. ST264 A more effective option for delivering ample combustion air to the stove is to duct air directly from outdoors to the stove. In fact, in some areas, provisions for outside combustion ...

  • Vermont Casting 1655, 1656, 1657, 1658, 1659 - page 19

    19 Vermont Castings Madison NOTE: Some chimneys need to be “primed,” or warmed up, before they will draw sufficiently to sustain a fire. T o correct this situation, roll up a couple pieces of newspaper , place them on top of the kindling and toward the back of the stove, light them, and close the doors. This should heat the chimney enough to in ...

  • Vermont Casting 1655, 1656, 1657, 1658, 1659 - page 20

    20 Vermont Castings Madison Maintenance Let the fire in the stove go out and allow the stove to cool completely before beginning any maintenance procedure. Care of the Cast Iron Surface An occasional dusting with a dry rag will keep the painted cast iron of your Madison looking new. The stove’s paint can be touched up as needed. First, clean the ...

  • Vermont Casting 1655, 1656, 1657, 1658, 1659 - page 21

    21 Vermont Castings Madison The Chimney System Creosote Your Madison is designed to reduce creosote buildup significantly. However, regular chimney inspection and maintenance must still be performed. For safety, good stove performance, and to protect your chimney and chimney connector, inspect your chimney and chimney connector on a regular schedul ...

  • Vermont Casting 1655, 1656, 1657, 1658, 1659 - page 22

    22 Vermont Castings Madison Draft Management Your stove is only one part of a system that includes the chimney, the operator, the fuel and the home. The other parts of the system will affect how well the stove works. When there is a good match between all the parts, the stove works well. W ood stove operation depends on natural (unforced) draft. Na ...

  • Vermont Casting 1655, 1656, 1657, 1658, 1659 - page 23

    23 Vermont Castings Madison There should be no more than eight feet of single-wall stove pipe between the stove and a chim- ney . Longer runs can cool the smoke enough to cause draft and creosote problems. Use double-wall stove pipe for longer runs. Single Venting Your stove requires a dedicated flue. Do not connect the stove to a flue used by any ...

  • Vermont Casting 1655, 1656, 1657, 1658, 1659 - page 24

    24 Vermont Castings Madison 1453 The Vermont Castings Majestic Products Company reserves the right to make changes in design, materials, specifications, prices and discontinue colors and products at any time, without notice. 45 44 39 37 36 32 28 27 23 15 4 1 35 8 6 2 12 26 42 30 31 20 19 11 22 3 13 9 21 40 29 17 38 14 7 5 18 10 33 16 43 34 24 25 41 ...

  • Vermont Casting 1655, 1656, 1657, 1658, 1659 - page 25

    25 Vermont Castings Madison Madison W oodburning Stove Model 1655 (continued) Item Description Part Number 23. Brick Support 30000804 24. Secondary Air Tube (Rear) 30001493 25. Secondary Air Tube (Middle) 30001494 26. Secondary Air Tube (Front) 30001495 27. Friction Spring 1201846 28. Leveller Blt, Hx Hd 1/4-20 x 1” Z 1201745 29. Washer, 1/4 pl 7 ...

  • Vermont Casting 1655, 1656, 1657, 1658, 1659 - page 26

    26 Vermont Castings Madison ...

  • Vermont Casting 1655, 1656, 1657, 1658, 1659 - page 27

    27 Vermont Castings Madison 4. This warranty does not cover a stove repaired by someone other than a Vermont Castings Majestic Products Company Authorized Dealer. 5. Damage to the unit while in transit is not covered by this warranty but is subject to claim against the common carrier. Contact the Authorized Dealer from whom you purchased your Madis ...

  • Vermont Casting 1655, 1656, 1657, 1658, 1659 - page 28

    28 Vermont Castings Madison © Vermont Castings, Majestic Products 410 Admiral Blvd. • Mississauga, Ontario, Canada L5T 2N6 • 905-670-7885 www.vermontcastings.com Ve r mont Castings, Majestic Products ...

メーカー Vermont Casting カテゴリー Stove

Vermont Casting 1655, 1656, 1657, 1658, 1659のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 1655, 1656, 1657, 1658, 1659の取扱説明書
- Vermont Castingの製品カード
- パンフレット
- またはVermont Casting 1655, 1656, 1657, 1658, 1659の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Vermont Casting 1655, 1656, 1657, 1658, 1659の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Vermont Casting 1655, 1656, 1657, 1658, 1659の取り付け説明書、サービスマニュアル、簡易説明書、またはVermont Casting 1655, 1656, 1657, 1658, 1659のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Vermont Casting 1655, 1656, 1657, 1658, 1659の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Vermont Casting 1655, 1656, 1657, 1658, 1659デバイスの取扱説明書はどのようなものですか？
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがVermont Casting 1655, 1656, 1657, 1658, 1659を使用するのを助ける技術的文書のことです。説明書は通常、全てのVermont Casting 1655, 1656, 1657, 1658, 1659ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Vermont Castingの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Vermont Casting 1655, 1656, 1657, 1658, 1659の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははVermont Casting 1655, 1656, 1657, 1658, 1659の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Vermont Casting 1655, 1656, 1657, 1658, 1659に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Vermont Casting 1655, 1656, 1657, 1658, 1659デバイスの基本機能を使うにあたってのヒント。 Vermont Casting 1655, 1656, 1657, 1658, 1659のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Vermont Casting 1655, 1656, 1657, 1658, 1659に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるVermont Casting 1655, 1656, 1657, 1658, 1659のメーカー/サービスへの連絡先に関する情報。

Vermont Casting 1655, 1656, 1657, 1658, 1659についてご質問がありますか？

次のフォームを使用してください

見つけた説明書を読んでもVermont Casting 1655, 1656, 1657, 1658, 1659の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがVermont Casting 1655, 1656, 1657, 1658, 1659で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

Captcha
新しい画像

コメント (0)