AT&T 76450の取扱説明書

32ページ 0.11 mb
ダウンロード

ページに移動 of 32

Summary
  • AT&T 76450 - page 1

    ATT-TP-76450 Common Systems Equipment Interconnection Standards for the ATT Local Exchange Companies and AT&T Corporation Abstract Presented in this document are the Common Systems Equipment Interconnection Standards for equipment placement and interconnection in the ATT LOCAL EXCHANGE companies Network. Users of this doc ument should note that ...

  • AT&T 76450 - page 2

    Common System s Connection Standards AT&T Services, Inc Date: August 31, 2007 ATT-TP-76450, Issue 9 Copyright ©2004 – 2006, AT&T Knowledge Ventures All rights reserved Page 2 GENERAL 1.1 Requirements This document provides the requirements for interconnection of new equipment in the AT&T Local Exchange Carrier and AT&T Corporatio ...

  • AT&T 76450 - page 3

    Common System s Connection Standards AT&T Services, Inc Date: August 31, 2007 ATT-TP-76450, Issue 9 Copyright ©2004 – 2006, AT&T Knowledge Ventures All rights reserved Page 3 If the product uses various components that are interconnected together, document will be applicable for interconnection between the various external components and ...

  • AT&T 76450 - page 4

    Common System s Connection Standards AT&T Services, Inc Date: August 31, 2007 ATT-TP-76450, Issue 9 Copyright ©2004 – 2006, AT&T Knowledge Ventures All rights reserved Page 4 • TP 76300, AT&T Installation Requirements • TP 76400, AT&T Design Engineering Requirements 1.8 Adherence to AT&T Standard Suppliers Within the Comm ...

  • AT&T 76450 - page 5

    Common System s Connection Standards AT&T Services, Inc Date: August 31, 2007 ATT-TP-76450, Issue 9 Copyright ©2004 – 2006, AT&T Knowledge Ventures All rights reserved Page 5 2 DC Power Interconnection Standards 2.1 GENERAL 2.1.1 Nominal -48v DC Nominal –48v DC is the standard platform for pow er delivery to any Network Element (NE). M ...

  • AT&T 76450 - page 6

    Common System s Connection Standards AT&T Services, Inc Date: August 31, 2007 ATT-TP-76450, Issue 9 Copyright ©2004 – 2006, AT&T Knowledge Ventures All rights reserved Page 6 2.1.3 Battery Return Conductor 2.1.3.1 Each power feeder shall have its own battery return conductor. This design concept shall also carry through directly to each ...

  • AT&T 76450 - page 7

    Common System s Connection Standards AT&T Services, Inc Date: August 31, 2007 ATT-TP-76450, Issue 9 Copyright ©2004 – 2006, AT&T Knowledge Ventures All rights reserved Page 7 This section describes the various acceptable DC power connectors and connections that are approved for use within AT&T. See Table 2-1 for a classification of a ...

  • AT&T 76450 - page 8

    Common System s Connection Standards AT&T Services, Inc Date: August 31, 2007 ATT-TP-76450, Issue 9 Copyright ©2004 – 2006, AT&T Knowledge Ventures All rights reserved Page 8 product. This termination or barrier strip s hould be able to accommodate a ring lug connectors that comply with the UL, CSA and Mil Spec listings. 2.3.3 18 AWG Pow ...

  • AT&T 76450 - page 9

    Common System s Connection Standards AT&T Services, Inc Date: August 31, 2007 ATT-TP-76450, Issue 9 Copyright ©2004 – 2006, AT&T Knowledge Ventures All rights reserved Page 9 2.5 Fusing of Capacitors Equipment incorporating the use of power distribution apparatus wh ich uses capacitors shall be fused to protect the power distribution bus ...

  • AT&T 76450 - page 10

    Common System s Connection Standards AT&T Services, Inc Date: August 31, 2007 ATT-TP-76450, Issue 9 Copyright ©2004 – 2006, AT&T Knowledge Ventures All rights reserved Page 10 Circuit Breakers - Only thermal magnetic and magnetic type DC circuit breakers are acceptable. Circuit breakers should adhere to a ll applicable UL and ANSI standa ...

  • AT&T 76450 - page 11

    Common System s Connection Standards AT&T Services, Inc Date: August 31, 2007 ATT-TP-76450, Issue 9 Copyright ©2004 – 2006, AT&T Knowledge Ventures All rights reserved Page 11 As an exception, there are some new network elements that employ high DC current demands that when collectively configured in a packaged bay arrangement may exceed ...

  • AT&T 76450 - page 12

    Common System s Connection Standards AT&T Services, Inc Date: August 31, 2007 ATT-TP-76450, Issue 9 Copyright ©2004 – 2006, AT&T Knowledge Ventures All rights reserved Page 12 3 Synchronization/Timing Standards The Building Integrated Timing Supply (BITS) c oncept is the method of providing Phase and Frequency synchronization. The BITS p ...

  • AT&T 76450 - page 13

    Common System s Connection Standards AT&T Services, Inc Date: August 31, 2007 ATT-TP-76450, Issue 9 Copyright ©2004 – 2006, AT&T Knowledge Ventures All rights reserved Page 13 office BITS, with primary and secondary DS1 (or Composite Clock) reference signals from separate T1 (DS1) or Composite Clock (CC) out put cards, with odd-even slot ...

  • AT&T 76450 - page 14

    Common System s Connection Standards AT&T Services, Inc Date: August 31, 2007 ATT-TP-76450, Issue 9 Copyright ©2004 – 2006, AT&T Knowledge Ventures All rights reserved Page 14 Footnote: The term "Network Element" is used within this document to refer to any and all equipment other than switching equi pment deployed in a CO or r ...

  • AT&T 76450 - page 15

    Common System s Connection Standards AT&T Services, Inc Date: August 31, 2007 ATT-TP-76450, Issue 9 Copyright ©2004 – 2006, AT&T Knowledge Ventures All rights reserved Page 15 (TBOS/TABS) E2A Discrete Least Preferred Footnote: A discrete telemetry interface may be provided, on an optional basis, in addition to higher level interfaces, to ...

  • AT&T 76450 - page 16

    Common System s Connection Standards AT&T Services, Inc Date: August 31, 2007 ATT-TP-76450, Issue 9 Copyright ©2004 – 2006, AT&T Knowledge Ventures All rights reserved Page 16 4.11 Housekeeping/Overhead Alarm Inputs All network elements that will be deployed in a non-central office environment, such as RT, CEV, Cabinet, etc., that are in ...

  • AT&T 76450 - page 17

    Common System s Connection Standards AT&T Services, Inc Date: August 31, 2007 ATT-TP-76450, Issue 9 Copyright ©2004 – 2006, AT&T Knowledge Ventures All rights reserved Page 17 5.7 Minimum Distance Between Connector Housing and 90 Degree Bend Minimum Fiber distance away from a connector housing to bend 90 degrees shall be 3.75- inches. Se ...

  • AT&T 76450 - page 18

    Common System s Connection Standards AT&T Services, Inc Date: August 31, 2007 ATT-TP-76450, Issue 9 Copyright ©2004 – 2006, AT&T Knowledge Ventures All rights reserved Page 18 5.13 Maximum optical power levels Optical aggregate power level must not exceed +16.8 dBm optical power level at any connector (Hazard Level 3b). If the product ex ...

  • AT&T 76450 - page 19

    Common System s Connection Standards AT&T Services, Inc Date: August 31, 2007 ATT-TP-76450, Issue 9 Copyright ©2004 – 2006, AT&T Knowledge Ventures All rights reserved Page 19 6.4 DS1 Cross-Connect Wire DS1 Cross-Connect Wire (Violet/Red) shall be spec ial high twist Wire to mitigate spectrum interference with DSL Wire (Violet/Blue). 6.5 ...

  • AT&T 76450 - page 20

    Common System s Connection Standards AT&T Services, Inc Date: August 31, 2007 ATT-TP-76450, Issue 9 Copyright ©2004 – 2006, AT&T Knowledge Ventures All rights reserved Page 20 Wire and Cable with UL Flammability Ratings of CMX and CMU must not be used within AT&T central offices as UL Flammability Ratings must be MP/CM(same floor), M ...

  • AT&T 76450 - page 21

    Common System s Connection Standards AT&T Services, Inc Date: August 31, 2007 ATT-TP-76450, Issue 9 Copyright ©2004 – 2006, AT&T Knowledge Ventures All rights reserved Page 21 Panels that use twisted pair jumper/cables le ss than 25 pair groups will be required to have a cable tray or rings. Do not place jumpers without a protection tray ...

  • AT&T 76450 - page 22

    Common System s Connection Standards AT&T Services, Inc Date: August 31, 2007 ATT-TP-76450, Issue 9 Copyright ©2004 – 2006, AT&T Knowledge Ventures All rights reserved Page 22 Documentation must be provided in both PD F and HTML format on a CD that is fully indexed and fully searchable. 7.2 Hard Copy Documentation Documentation must be f ...

  • AT&T 76450 - page 23

    Common System s Connection Standards AT&T Services, Inc Date: August 31, 2007 ATT-TP-76450, Issue 9 Copyright ©2004 – 2006, AT&T Knowledge Ventures All rights reserved Page 23 7.9 Consistent Terminology throughout Documentation Per GR-454-CORE, Section 2.4, terminology must remain consistent throughout all documentation for a platform. E ...

  • AT&T 76450 - page 24

    Common System s Connection Standards AT&T Services, Inc Date: August 31, 2007 ATT-TP-76450, Issue 9 Copyright ©2004 – 2006, AT&T Knowledge Ventures All rights reserved Page 24 Note: The expectation is that a 2-3 page extraction from a larger manual will be submitted as evidence for each of the tasks above. Based on this information, AT&a ...

  • AT&T 76450 - page 25

    Common System s Connection Standards AT&T Services, Inc Date: August 31, 2007 ATT-TP-76450, Issue 9 Copyright ©2004 – 2006, AT&T Knowledge Ventures All rights reserved Page 25 9 APPENDIX A – ATT-TP-76450 Checklist Instructions and Process 9.1 Purpose The purpose of this appendix is to assist product suppliers with preparing and furnish ...

  • AT&T 76450 - page 26

    Common System s Connection Standards AT&T Services, Inc Date: August 31, 2007 ATT-TP-76450, Issue 9 Copyright ©2004 – 2006, AT&T Knowledge Ventures All rights reserved Page 26 Footnote references for requirements marked “N/A” for not applicable or “Part” for partially compliant will be reviewed by the AT&T SME for that requir ...

  • AT&T 76450 - page 27

    Common System s Connection Standards AT&T Services, Inc Date: August 31, 2007 ATT-TP-76450, Issue 9 Copyright ©2004 – 2006, AT&T Knowledge Ventures All rights reserved Page 27 Appendix B – ATT-TP 76450 Checklist Manufacturer:________________________________ Date: ______________________ Equipment Name/Model Number, etc.: _______________ ...

  • AT&T 76450 - page 28

    Common System s Connection Standards AT&T Services, Inc Date: August 31, 2007 ATT-TP-76450, Issue 9 Copyright ©2004 – 2006, AT&T Knowledge Ventures All rights reserved Page 28 3.2 Primary and Secondary Interfaces 3.3 Clock Output Lead Cabling 3.4 Redundancy of timing inputs 3.5 Output Card Exhaustion 4 ALARM STANDARDS 4.1 Equipment surve ...

  • AT&T 76450 - page 29

    Common System s Connection Standards AT&T Services, Inc Date: August 31, 2007 ATT-TP-76450, Issue 9 Copyright ©2004 – 2006, AT&T Knowledge Ventures All rights reserved Page 29 6.11 Central Office Copper Wire and Cable 6.12 Central Office Copper Coaxial Cable 6.13 Central Office Copper "Bits" Synchronous Timing Cables 6.14 Centr ...

  • AT&T 76450 - page 30

    Common System s Connection Standards AT&T Services, Inc Date: August 31, 2007 ATT-TP-76450, Issue 9 Copyright ©2004 – 2006, AT&T Knowledge Ventures All rights reserved Page 30 10 APPENDIX C - References ATT TP documents may be obtained on the AT&T Technical Publication and Nebs Web site . Telcordia documents may be obtained directly ...

  • AT&T 76450 - page 31

    Common System s Connection Standards AT&T Services, Inc Date: August 31, 2007 ATT-TP-76450, Issue 9 Copyright ©2004 – 2006, AT&T Knowledge Ventures All rights reserved Page 31 11 Appendix D - ATT Contact List Wing Eng, Area Manager-Common Systems Standards, DSX, Copper Cable Standards (925) 823-4616, E-Mail: we2583@camail.att.com Doug Fl ...

  • AT&T 76450 - page 32

    Common System s Connection Standards AT&T Services, Inc Date: August 31, 2007 ATT-TP-76450, Issue 9 Copyright ©2004 – 2006, AT&T Knowledge Ventures All rights reserved Page 32 ...

メーカー AT&T カテゴリー Network Router

AT&T 76450のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 76450の取扱説明書
- AT&Tの製品カード
- パンフレット
- またはAT&T 76450の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、AT&T 76450の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、AT&T 76450の取り付け説明書、サービスマニュアル、簡易説明書、またはAT&T 76450のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、AT&T 76450の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

AT&T 76450デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがAT&T 76450を使用するのを助ける技術的文書のことです。説明書は通常、全てのAT&T 76450ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

AT&Tの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. AT&T 76450の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははAT&T 76450の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。AT&T 76450に関してこのドキュメントで見つけることができる全てのヒントの目次
3. AT&T 76450デバイスの基本機能を使うにあたってのヒント。 AT&T 76450のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。AT&T 76450に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるAT&T 76450のメーカー/サービスへの連絡先に関する情報。

AT&T 76450についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもAT&T 76450の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがAT&T 76450で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)