Honeywell 4500の取扱説明書

36ページ 0.14 mb
ダウンロード

ページに移動 of 36

Summary
  • Honeywell 4500 - page 1

    4500 THERMOSTAT INSTALLATION INSTRUCTIONS N7970 7/97 ...

  • Honeywell 4500 - page 2

    ii Table of Contents Section 1. GENERAL DESCRIPTION ................................................................................ 1-1 Application and Descriptio n .............................................................................. 1-1 4500 Specificatio ns ................................................................................ ...

  • Honeywell 4500 - page 3

    SECTION 1 General Description •••••••••••••••••••••••••••••••••••••••••• In This Section ♦ Application and Description ♦ 4500 Specifications ••••••••••••••••••••••••••••••••••••••••? ...

  • Honeywell 4500 - page 4

    4500 Installation Instructions 1-2 4500 Specifications Operating Range 32 to 122 degrees F., 0 to 50 deg rees C. Temperature Setting Range 45 to 99 degr ees F., 7 to 37 degrees C. Temperature Reading Accuracy ± 2 degrees F., ± 1 degr ee C. Voltage 11 to 14VDC Current Draw 50 mA Air Conditioner Compressor Off Cycle 5 minutes minimum Physical Dimen ...

  • Honeywell 4500 - page 5

    2-1 SECTION 2 Front Panel Controls •••••••••••••••••••••••••••••••••••••••••• In This Section ♦ Description •••••••••••••••••••••••••••••••••••••••••• Description Referring to Fig ...

  • Honeywell 4500 - page 6

    4500 Thermostat Installation Instructions 2-2 You will not be able to adjust room temperature by phone when the 4500 is bypassed. There are s everal uses for the BYPAS S swit ch function: • Allows the u ser to go back to the ir pre-e xisting th ermostat at any time. • Allows heating/air co nditioning serv ice peo ple to by pass the 4500 during ...

  • Honeywell 4500 - page 7

    3-1 SECTION 3 Installing the 4500 Thermostat •••••••••••••••••••••••••••••••••••••••••• In This Section ♦ General ♦ Mounting and Installat ion ♦ Wiring Connections ♦ Step-by-St ep Installation Instruct ions ♦ Setting the DIP Sw itch ♦ Setting the F an Co ...

  • Honeywell 4500 - page 8

    4500 Thermostat Installation Instructions 3-2 While installation of the 4500 is possible w ithout the se rvices of a HVAC contractor, some installers will prefe r to have an HVAC contracto r connect the 4500 to the HVAC sy stem and test its op eration. This is re commended if you do not have HVAC experience. In cases where you prefer to do the enti ...

  • Honeywell 4500 - page 9

    Section 3. Installing the 4500 Thermostat 3-3 Sometimes , R and Rc are jumpered t ogether at the premi ses t hermostat and are connected to the HVAC system with a single common wire. This is the case if both heating and air conditioning are controlled by the same contro l system . The remaining three wires connect the thermostat to the heating, coo ...

  • Honeywell 4500 - page 10

    4500 Thermostat Installation Instructions 3-4 If you are installing the 4500 in a heat on ly system, the setup will lo ok like Figure 4 belo w. R Heat (W) Fan (G) R Heat (W) Fan (G) PREMISES THERMOSTAT 4286 PHONE MODULE IN OUT W G 4500 THERMOSTAT 68 5 3 HVAC System Figure 4. 4500 Thermostat w ith Heating System Only Some heating sy stems, such as t ...

  • Honeywell 4500 - page 11

    Section 3. Installing the 4500 Thermostat 3-5 When installing the 4500 the rmostat, refe r to the Summary o f Connectio ns at the back of this manual. This diag ram depicts the 4500's terminal strip and shows e xactly how th e ther mostat mu st be wire d. The heating/coo ling system and the rmostat you are w orking on may not have all the conn ...

  • Honeywell 4500 - page 12

    4500 Thermostat Installation Instructions 3-6 5. Connect the tagged wires removed in step 4 from the HVAC sys tem to the applicable terminals o f the 4500. Ref er to the f ollowing table for pro per connection information. Table 1 Lead from HVAC system Terminal on 4500 Fan (green) (G) 8 Cool (yellow ) (Y) 7 Heat (white) (W) 6 6. Connect a wire to e ...

  • Honeywell 4500 - page 13

    Section 3. Installing the 4500 Thermostat 3-7 9. Connect the 4500 to the 4286 pho ne modu le using the supp lied key pad type cable. The cable contains fo ur wires of differe nt colors wh ich are connected to the 4500 as indicated in the follo wing table: Table 4 Wire from 4286 cable Terminal on 4500 Green 9 Red 10 Black 11 Yellow 12 If two 4500 th ...

  • Honeywell 4500 - page 14

    4500 Thermostat Installation Instructions 3-8 10. Once the 4500 is mounted, yo u need to set its DIP sw itch and 3-pin fan control jumper. T h es e procedures are des cribed below. Setting the DIP S witc h The 4500 includes a DIP sw itch for setting the addre ss of the the rmostat. The 4286 phon e access mod ule can include up to 2 thermostats p er ...

  • Honeywell 4500 - page 15

    Section 3. Installing the 4500 Thermostat 3-9 Setting the Fan Control Pins The three fan co ntrol pins in the center of the 4500 are use d to control the operation of the HVAC system’s fan. Us ing the jumper provided, you can select whether or not the sys tem’s fan s hould turn on wit h cooling and heating, or t urn on only with cool ing. The o ...

  • Honeywell 4500 - page 16

    4500 Thermostat Installation Instructions 3-10 ...

  • Honeywell 4500 - page 17

    4-1 SECTION 4 Programming the 4286 to Add 4500 Thermostat(s) •••••••••••••••••••••••••••••••••••••••••• In This Section ♦ General ♦ To Enter and Use the 4286 Programmi ng Mode ♦ Programming Fields ♦ Step-by-St ep P rogramming Instructions ♦ Thermostat Voic ...

  • Honeywell 4500 - page 18

    4500 Thermostat Installation Instructions 4-2 To Enter and Use the 4286 Programming Mode: 1. Pick up a premise s touch tone phon e connected to the 4286 handset output. 2. Enter the 2 dig it phone co de on the phon e keyp ad. If the 4286 is announcing, wait until syst em s tatus announcement s have been complete d, then pre ss # 98. The 4286 will a ...

  • Honeywell 4500 - page 19

    Section 4. Programming the 4286 to Add Thermostat(s) 4-3 If The System Contains Addressable Keypad Non- Addressable Keypad Select “MUTE” (4286 #97 Mode) Comments Thermostat Speake r 01 - 30 (exclud e 04)* 31 No Assign 4500 to same partition as keypad Thermostat No Speaker 01 - 30 (exclud e 04)* 31 Yes Assign 4500 to same partition as keypad No ...

  • Honeywell 4500 - page 20

    4500 Thermostat Installation Instructions 4-4 Field 02: Control Panel Type 1 = Vista-10 and Vista-10SE, Via-30P and Via-30PSE, 4140XMP (with v oice upgrade EPROM) 2 = Vista-20, Vista-20HW and Vista-20SE [default] 4 = Vista-40, Vista-50P, Vista-100, and Vista- 120. Field 03: Units of Temperature 0 = temperat ures in degrees F. [default] 1 = temperat ...

  • Honeywell 4500 - page 21

    Section 4. Programming the 4286 to Add Thermostat(s) 4-5 The first d igit ind icates the sw ing abo ve the set po int; the se cond digit ind icates the swing below the set po int, as indicated be low: Temperature Span (Swing) “ABOVE “BELOW” Digit #1 Digit #2 1 = 0.0 deg. F. (0.0 d eg. C.) 1 = 0.0 deg . F. ( 0.0 deg. C.) 2 = +0.5 deg. F. (0.3 ...

  • Honeywell 4500 - page 22

    4500 Thermostat Installation Instructions 4-6 For Fields 07-09, s elect the 3-digit wor d codes from Table 5 for eac h des criptor. If you want less than a 3-w ord description for the thermos tat, set unused descriptors to 0 0 0 . Note: Fields 07 throug h 09 select a vo ice announcem ent to be associated with thermostat #1. For example, i f you wan ...

  • Honeywell 4500 - page 23

    Section 4. Programming the 4286 to Add Thermostat(s) 4-7 The first d igit ind icates the sw ing abo ve the set po int; the se cond digit indicates the sw ing below the set p oint, as indicated below: Temperature Span (Swing) “ABOVE “BELOW” Digit #1 Digit #2 1 = 0.0 deg. F. (0.0 d eg. C.) 1 = 0.0 deg . F. ( 0.0 deg. C.) 2 = +0.5 deg. F. (0.3 d ...

  • Honeywell 4500 - page 24

    4500 Thermostat Installation Instructions 4-8 For Fields 13-15, s elect the 3-digit wor d codes from Table 5 for eac h des criptor. If you want less than a 3-w ord description for the thermos tat, set unused descriptors to 0 0 0 . Note: Fields 13 thru 15 sele ct a voice anno uncemen t to be associate d with thermostat #2. For example, if you wanted ...

  • Honeywell 4500 - page 25

    Section 4. Programming the 4286 to Add Thermostat(s) 4-9 THERMOSTAT VOICE DESCRIPTORS VOCABULARY (4286 Phone Access Mod ule Only) The follo wing three d igit codes are used to p rogram thermo stat descripto rs into the 4286 programming f ields 07 thru 09 and fields 13 thru 15. Table 5 WORD INDEX WORD WORD INDEX WORD WORD INDEX WORD WORD INDEX WORD ...

  • Honeywell 4500 - page 26

    4500 Thermostat Installation Instructions 4-10 ...

  • Honeywell 4500 - page 27

    5-1 SECTION 5 Testing the 4500 With the 4286 •••••••••••••••••••••••••••••••••••••••••• In This Section ♦ General ♦ Step-by-St ep Testing P rocedure ♦ Setting the Premises thermostat ♦ Setting the 4500 Thermostat ♦ Menu Selections ••••••••? ...

  • Honeywell 4500 - page 28

    4500 Thermostat Installation Instructions 5-2 5. Check the heat mode operation of the premi ses t h ermos tat b y varying it s set point and v erifying that the heating sy stem turns on and o ff. 6. If the 4500 thermo stat will control an air co nditioning syste m, set the 4500 front p anel slide sw itches to ACTIVE and COOL . Set the premis es the ...

  • Honeywell 4500 - page 29

    Section 5. Testing the 4500 With the 4286 Phone Module 5-3 2. Obtain phone a ccess from t he phone module. Enter the 2 -digit phone code. Enter the 4-digit system code i f prompt ed. 3. Press # 99 on the phone k eypad after th e compl ete sta tus announcement . 4. The 4286 will announce: “Thermostat Mode.” The tempe rature setting f or thermost ...

  • Honeywell 4500 - page 30

    4500 Thermostat Installation Instructions 5-4 “For set-back on/off, enter 3.” Turning off se t-back will result in it remaining disabled while arme d away, until the ne xt time the sy stem is disarmed. This feature allo ws the user to turn o ff the se t-back befo re returning ho me, so that the premise s will have time to return to a co mfortab ...

  • Honeywell 4500 - page 31

    6-1 SECTION 6 Troubleshooting •••••••••••••••••••••••••••••••••••••••••• In This Section ♦ General ♦ Troubleshooting Typical Thermostat Se t -Up Problems •••••••••••••••••••••••••••••••••••• ...

  • Honeywell 4500 - page 32

    4500 Thermostat Installation Instructions 6-2 4500 or premises thermost at fails to c ontrol the H VAC system. 1. Check set po ints in 4500 and prem ises thermostat to e nsure they are set properly. 2. If BYPASS of 4500 via its fro nt panel switch cause s existing thermo stat to work pr operly , then pro blem is in the 4500 wiring or within the 450 ...

  • Honeywell 4500 - page 33

    A-1 SECTION 7 Appendices •••••••••••••••••••••••••••••••••••••••••• In This Section ♦ Federal Communications Commission (FCC) Part 15 St atement ♦ Ademco Limited Warranty ♦ Summary of Connections •••••••••••••••••••••? ...

  • Honeywell 4500 - page 34

    4500 Thermostat Installation Instructions A-2 ADEMCO Limit ed Warrant y Alarm Device Manufacturing Company , a Division o f Pittway Co rporation, and its divisions, subsidiaries and affiliates (“Seller”) , 165 Eileen Way , Syosse t, New Yo rk 11791, warrants its products to be in confo rmance with its own p lans and specif ications and to be fr ...

  • Honeywell 4500 - page 35

    Appendices A-3 1 2 3 4 5 6 7 8 9 10 11 12 5 4 3 2 1 TEMPERATURE SENSOR 1 2 3 FAN CONTROL PINS DOWN UP Cool Heat Fan } TO HVAC SYSTEM } TO 4286 VOICE MODULE } TO PREMISES THERMOSTAT Cool Heat Fan Green Red Black Yellow JUMPER PLACED ON 1 and 2 = FAN ON WITH HEAT AND COOL JUMPER PLACED ON 2 and 3 = FAN ON WITH COOL ONLY DIP SWITCH Two jumper wires ar ...

  • Honeywell 4500 - page 36

    165 Eileen Wa y , Sy osset, New Y ork, 11791 Copyright © 1997 PITTW A Y CORPORA TION N7970 7/97 ...

メーカー Honeywell カテゴリー Thermostat

Honeywell 4500のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 4500の取扱説明書
- Honeywellの製品カード
- パンフレット
- またはHoneywell 4500の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Honeywell 4500の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Honeywell 4500の取り付け説明書、サービスマニュアル、簡易説明書、またはHoneywell 4500のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Honeywell 4500の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Honeywell 4500デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがHoneywell 4500を使用するのを助ける技術的文書のことです。説明書は通常、全てのHoneywell 4500ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Honeywellの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Honeywell 4500の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははHoneywell 4500の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Honeywell 4500に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Honeywell 4500デバイスの基本機能を使うにあたってのヒント。 Honeywell 4500のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Honeywell 4500に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるHoneywell 4500のメーカー/サービスへの連絡先に関する情報。

Honeywell 4500についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもHoneywell 4500の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがHoneywell 4500で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)