-
Hunter Fan 43045 - page 1
43045-01 10/15/2009 1 Installation Guide Energy Star Bath Fan Models 82043 READ and SA VE THESE INSTRUCTIONS ENGLISH See page 2 ESp añoL V ea la página 19 ...
-
Hunter Fan 43045 - page 2
43045-01 10/15/2009 2 1) Read all instructions before attempting to install or use this appliance. This appliance is for general ventilating use only . Do not use this appliance for ventilating hazardous or explosive materials. Follow the heating equipment manufacturer ’s guideline and safety standards, such as those published by the National Fir ...
-
Hunter Fan 43045 - page 3
43045-01 10/15/2009 3 6) Never place a switch where it can be reached from a tub or shower . Do not install this appliance in a tub or shower enclosure. 7) Installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable codes and standards, including fire-rated construction codes and standards. 8) When ...
-
Hunter Fan 43045 - page 4
43045-01 10/15/2009 4 F G I L M x2 N x6 * * A B C 98141-01-000 03242-07-133 98142-01-000 x2 D 97134-01-000 74508-03-133 Housing Wiring Co ver F an Assembly 3/8” Cable Connector Light F ixture Wiring Co ver Screw Check all the parts. If damag ed , call 1-888-830-1326 for replacement. x4 E Mounting Screws F an Mounting Screws * NOTE: Strain relief ...
-
Hunter Fan 43045 - page 5
43045-01 10/15/2009 5 Loosen the wiring cover screw . Remove the fan assembly from the housing. Remove the wiring cover . D E C Choose Installation Option For New Construction - attaching to joist, go to step A1, page 5. For New Construction - suspended between, joists go to step B1, page 7. For Existing Construction - accessible from above, go to ...
-
Hunter Fan 43045 - page 6
43045-01 10/15/2009 6 A 1 Section A - New Construction - attaching to joist Drive mounting screws (supplied) into joist or framing. Position the correct depth mark at the bottom edge of the joist based upon the the thickness of your sheetrock. 5/8 1/2 5/8 1/2 A 2 Pop out a wiring access slug. OR Install the wiring and the strain relief into the wir ...
-
Hunter Fan 43045 - page 7
43045-01 10/15/2009 7 A 6 Connect 6” duct and vent to the outside. Use duct tape to secure joints. If ducting does not fit securely , an adapter may need to be purchased. Vaya a la sección E – Instalación Final en la página 14. Section B - New Construction – suspended between joists Pop out a wiring access slug. B 1 OR Slide the mounting r ...
-
Hunter Fan 43045 - page 8
43045-01 10/15/2009 8 Mark position of screws by using holes as a template. Drill a pilot hole at the TOP of each outline. B4 1/16” bit B5 Insert mounting screws, leaving space between the screw head and the joist. (Screws are supplied.) Attach the rails onto the screws. B6 B7 B8 Tighten screws. Run the power supply wire through the strain relief ...
-
Hunter Fan 43045 - page 9
43045-01 10/15/2009 9 B10 Install the wiring and the strain relief into the wiring access hole you made earlier . B11 Connect 6” duct and vent to the outside. Use duct tape to secure joints. If ducting does not fit securely , an adapter may need to be purchased. Vaya a la sección E – Instalación Final en la página 14. 11” 9 5⁄8” C1 Rem ...
-
Hunter Fan 43045 - page 10
43045-01 10/15/2009 10 Slide the mounting rails into brackets. C3 5/8 1/2 5/8 1/2 C4 Using the depth markings on the housing, position the bottom edge of the housing so that it will be flush with the sheetrock. Pop out a wiring access slug. C6 C5 Mark position of screws by using holes as a template. Drill a pilot hole at the TOP of each outline, AS ...
-
Hunter Fan 43045 - page 11
43045-01 10/15/2009 1 1 C7 Insert mounting screws, leaving space between the screw head and the joist. (Screws are supplied.) Attach the rails onto the screws. C8 C9 Tighten screws. 3” C 1 0 Run the power supply wire through the strain relief, leaving 3” between the end of the wire and the strain relief. Tighten the strain relief around the wir ...
-
Hunter Fan 43045 - page 12
43045-01 10/15/2009 12 Vaya a la sección E – Instalación Final en la página 14. Section D - Existing Construction – accessible from below Remove one of the wiring access slugs on the top of the housing. Use a second wiring access plug if needed. EXISTING F AN D 3 Remove an existing fan and check to make sure the opening is large enough to ac ...
-
Hunter Fan 43045 - page 13
43045-01 10/15/2009 13 Connect 6” duct and vent to the outside. Use duct tape to secure joints. If ducting does not fit securely , an adapter may need to be purchased. Install the wiring and the strain relief into the wiring access hole you made earlier . Position the bottom edge of the housing flush with the sheetrock. Move the housing into the ...
-
Hunter Fan 43045 - page 14
43045-01 10/15/2009 14 E2 E 3 Connect fan wiring harness. DO NOT ALLOW THE F AN TO HANG FROM THE WIRING HARNESS. INST ALLA TION IS EASIER IF TWO PEOPLE ARE INVOL VED. Install the wiring cover box. Make sure all wiring connec- tions are inside the wiring cover box. Section E - Final Installation NOTE: Though this final installation section shows the ...
-
Hunter Fan 43045 - page 15
43045-01 10/15/2009 15 E5 Secure the fan assembly by tightening the two fan mounting screws. E7 Install the strain relief bracket. DO NOT ALLOW THE LIGHT FIXTURE TO HANG FROM THE WIRING HARNESS. INST ALLA TION IS EASIER IF TWO PEOPLE ARE INVOL VED. E8 E6 E6 E7 Remove thumbnuts. Remove light bulb cover . Plug in wiring harness. Position lighting fix ...
-
Hunter Fan 43045 - page 16
43045-01 10/15/2009 16 E15 Complete. E9 E13 Install light bulb cover . Restore power at the source. E11 E12 Secure the fan assembly by tightening the two fan mounting thumbnuts. Install light bulbs. E12 Install night light. ...
-
Hunter Fan 43045 - page 17
43045-01 10/15/2009 17 T rouble Shooting Problem: Fan does not come on. Solution: • T urn power on, replace fuse, or reset breaker. • Hunter Fan Bath V entilators are extremely quiet. T o conrm that the fan is running, place your hand near the vents to feel the air movement. • Check all plug connections to be sure they are secure. • Chec ...
-
Hunter Fan 43045 - page 18
43045-01 10/15/2009 18 Hunter Fan Company Bath Fan LIMITED W ARRANTY Hunter Fan Company makes the following limited warranty to the original user or consumer purchaser of this Hunter Bath Fan: If any part of your Hunter Bath Fan fails at any time within one year after the date of sale to you due to a defect in material or workmanship, we will repai ...
Hunter Fan 43045についてご質問がありますか？
次のフォームを使用してください
見つけた説明書を読んでもHunter Fan 43045の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがHunter Fan 43045で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。