Bissell 1699の取扱説明書

22ページ 0.87 mb
ダウンロード

ページに移動 of 22

Summary
  • Bissell 1699 - page 1

    POWERSTEAMER® PROHEAT PRO-TECH™ #1698’s, #1699’s, & #7920’s Service Center Re p air Guide ...

  • Bissell 1699 - page 2

    B issell PowerSteamer® ProHeat™ Series Service Center Repair Gu ide Printed Fe bruary, 2001 1/30/200 4 (Revis ion 1) 1 TABLE OF CONTENTS How to use this Repair Guide Page 2 UL Recommended High Voltage Test Page 2 Using the Servicing Platform Page 3 Preliminary Diagnostic Checks Page 3 Functional Systems Check Page 5 Taking the Unit Apart Page 6 ...

  • Bissell 1699 - page 3

    B issell PowerSteamer® ProHeat™ Series Service Center Repair Gu ide Printed Fe bruary, 2001 1/30/200 4 (Revis ion 1) 2 HOW TO USE THIS REPAIR GUIDE The instructions in this Repair Guide pertain to the B issell PowerSteamer ProHeat (#1698) and the Bissell ProHeat ClearView(#1699) . The information identifies those parts and components which are m ...

  • Bissell 1699 - page 4

    B issell PowerSteamer® ProHeat™ Series Service Center Repair Gu ide Printed Fe bruary, 2001 1/30/200 4 (Revis ion 1) 3 USING THE SERVICING PLATFORM Begin by placing the unit on the Servicing Platfo rm. Servicing Platform should fit securely under the unit and raise its wheels off the servicing surface. PRELIMINARY DIAGNOSTIC CHECKS 1. Test the t ...

  • Bissell 1699 - page 5

    B issell PowerSteamer® ProHeat™ Series Service Center Repair Gu ide Printed Fe bruary, 2001 1/30/200 4 (Revis ion 1) 4 3. Check seals on Clear Water Tank and Solution Tank. If necessary, re-seat or replace seals. 4. Check valve action on Clear Water Tank a nd Solution Tank by depressing them with your finger. The valve should move up and down. R ...

  • Bissell 1699 - page 6

    B issell PowerSteamer® ProHeat™ Series Service Center Repair Gu ide Printed Fe bruary, 2001 1/30/200 4 (Revis ion 1) 5 8. Manually rotate motor shaft to determine that motor, brush and pu mp are moving smoothly and quietly. 9. Remove any debris which may be hinder ing the free movement of these components. FUNCTIONAL SYSTEMS CHECK 1. Fill tank b ...

  • Bissell 1699 - page 7

    B issell PowerSteamer® ProHeat™ Series Service Center Repair Gu ide Printed Fe bruary, 2001 1/30/200 4 (Revis ion 1) 6 TAKING THE UNIT APART 1. Unplug the unit. 2. Recline the handle backwards fully. 3. Turn SmartMix to "normal" traffic setting. 4. Remove the Solution and Clean Water Tanks. 5. Remove clear flow indicator cap, red spinn ...

  • Bissell 1699 - page 8

    B issell PowerSteamer® ProHeat™ Series Service Center Repair Gu ide Printed Fe bruary, 2001 1/30/200 4 (Revis ion 1) 7 10. Check lines for evidence of pinching and restri cted flow. Straighten and un-pinch lines as necessary. ( See base photo page 18) 11. After removing housing, check that the Sm artMix piston is still positioned withi n the mai ...

  • Bissell 1699 - page 9

    B issell PowerSteamer® ProHeat™ Series Service Center Repair Gu ide Printed Fe bruary, 2001 1/30/200 4 (Revis ion 1) 8 LOWER HANDLE ISSUES 1. Handles must be reassembled to ensure that hoses are not pinched. 2. Clear any blockages in the heater inlet and outlet lines with a finishing nail or similar object. 3. To open the heater, remove screws l ...

  • Bissell 1699 - page 10

    B issell PowerSteamer® ProHeat™ Series Service Center Repair Gu ide Printed Fe bruary, 2001 1/30/200 4 (Revis ion 1) 9 2. Make certain the background window has its tabs placed properl y. 3. Make certain the gasket is in place on top of the background window. MOTOR REPLACEMENT PROCEDURE 1. Remove main housing. 2. Rotate upholstery duct back towa ...

  • Bissell 1699 - page 11

    B issell PowerSteamer® ProHeat™ Series Service Center Repair Gu ide Printed Fe bruary, 2001 1/30/200 4 (Revis ion 1) 10 5. Remove the four screws on the motor cover. 6. Rock the motor duct out of position. 7. Lift out the motor. 8. Disconnect all wires. 9. Remove, clean and save the two gaskets on the motor. 10. Clean any debris from motor cover ...

  • Bissell 1699 - page 12

    B issell PowerSteamer® ProHeat™ Series Service Center Repair Gu ide Printed Fe bruary, 2001 1/30/200 4 (Revis ion 1) 11 13. Attach the "hot" and "neutral" terminals onto the new motor. 14. Turn the motor so that the "ground" ter minal is oriented downward. 15. Loop the wires around the bottom of the motor, then out ...

  • Bissell 1699 - page 13

    B issell PowerSteamer® ProHeat™ Series Service Center Repair Gu ide Printed Fe bruary, 2001 1/30/200 4 (Revis ion 1) 12 20. Replace the spray tips. 21. Replace the flow indicator by pulling the two tubes downward and making sure the flow indicator is seated snugly. 22. Replace all tubing and wiring in its proper pos ition. See full size photo of ...

  • Bissell 1699 - page 14

    B issell PowerSteamer® ProHeat™ Series Service Center Repair Gu ide Printed Fe bruary, 2001 1/30/200 4 (Revis ion 1) 13 PUTTING THE UNIT BACK TOGETHER 1. Follow the assembly diagram to ensure th at all parts are replaced properly . 2. Make sure the foot pedal is in the proper position. 3. The SmartMix should be properly loaded into the main hous ...

  • Bissell 1699 - page 15

    B issell PowerSteamer® ProHeat™ Series Service Center Repair Gu ide Printed Fe bruary, 2001 1/30/200 4 (Revis ion 1) 14 7. Clean any debris from the flow indicator. Insert with post up, then lightly tighten flow indicator cap. 8. Make sure the rope gasket for the window is in place on the housing. Also, check to see that the rubber gasket is in ...

  • Bissell 1699 - page 16

    B issell PowerSteamer® ProHeat™ Series Service Center Repair Gu ide Printed Fe bruary, 2001 1/30/200 4 (Revis ion 1) 15 PUMP REPLACEMENT 1. Unplug the unit. 2. Remove the two solution ta nks. 3. Remove spray tips from guides. 4. Remove the brush and cog belt by removing th e screw from the orange retaining collar. 5. Remove belt from pulley. 6. ...

  • Bissell 1699 - page 17

    B issell PowerSteamer® ProHeat™ Series Service Center Repair Gu ide Printed Fe bruary, 2001 1/30/200 4 (Revis ion 1) 16 8. Place stretch belt on new pump. 9. Re-seat new pump into position and screw into place (4 screws). 10. Reattach tubing 11. Reattach brush, cogbelt, and retainer arm. 12. Screw orange retaining collar back in place. 13. Reset ...

  • Bissell 1699 - page 18

    B issell PowerSteamer® ProHeat™ Series Service Center Repair Gu ide Printed Fe bruary, 2001 1/30/200 4 (Revis ion 1) 17 Wiring Diagram ...

  • Bissell 1699 - page 19

    B issell PowerSteamer® ProHeat™ Series Service Center Repair Gu ide Printed Fe bruary, 2001 1/30/200 4 (Revis ion 1) 18 Overhead View of Base ...

  • Bissell 1699 - page 20

    B issell PowerSteamer® ProHeat™ Series Service Center Repair Gu ide Printed Fe bruary, 2001 1/30/200 4 (Revis ion 1) 19 Lower Handle Disassembly 1. Remove the two screws located near the botto m of the tool caddy on the back of the machine. 2. Remove the two bolts and nuts that go t hrough the upper part of the tool caddy and handle assembly. 3. ...

  • Bissell 1699 - page 21

    B issell PowerSteamer® ProHeat™ Series Service Center Repair Gu ide Printed Fe bruary, 2001 1/30/200 4 (Revis ion 1) 20 Circuit Board Replacement 1. Disassemble lower handle assembly accordin g to instructions on page nineteen. 2. Remove the black circuit board wire from the power switch (this is the black wire that runs from the switch to the c ...

  • Bissell 1699 - page 22

    B issell PowerSteamer® ProHeat™ Series Service Center Repair Gu ide Printed Fe bruary, 2001 1/30/200 4 (Revis ion 1) 21 Speed Sensor Replacement 1. Remove the main housing according to instructions on page six. 2. Remove the right side wheel (held in place by an E-clip on the end of the axle). 3. Gently lift plastic retaining tab up and away fro ...

メーカー Bissell カテゴリー Carpet Cleaner

Bissell 1699のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 1699の取扱説明書
- Bissellの製品カード
- パンフレット
- またはBissell 1699の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Bissell 1699の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Bissell 1699の取り付け説明書、サービスマニュアル、簡易説明書、またはBissell 1699のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Bissell 1699の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Bissell 1699デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがBissell 1699を使用するのを助ける技術的文書のことです。説明書は通常、全てのBissell 1699ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Bissellの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Bissell 1699の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははBissell 1699の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Bissell 1699に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Bissell 1699デバイスの基本機能を使うにあたってのヒント。 Bissell 1699のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Bissell 1699に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるBissell 1699のメーカー/サービスへの連絡先に関する情報。

Bissell 1699についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもBissell 1699の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがBissell 1699で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)