-
Yard-Man 7100-1 - page 1
and f ., . ...' YARD -~.;1AN co. P. C. BOX 36940 CLE'JELAt'JD, OHIO 44136 1410 West Ganson Street -Jackson, ~ichigan 49202 PRINTED.IN U..S.A. 0611-724A ...
-
Yard-Man 7100-1 - page 2
tI, i' , b.,fj;, .;, RULES FO.~~ SAFE OPERATION .; ~ ~ Your SNOW THROWER is a precision piece of snow throwing equipment. Engineering skill and experience have been combined to provide the ultimate in safety and efficiency. As with any type of power equipment, carelessness or error on the part of the operator can result in injury. EXERCISE EXT ...
-
Yard-Man 7100-1 - page 3
"'~-"" -, .,. ., ,-~ ..,. -., ~,. l_SUGGESTIONS I ~ ...:.~~,:, , i;J;~:"';, MAINTENAN tE';' !~ FOR ,,~~~~~; ~:'; ':.;~, " t.'~" ,-.: ;1t5::~::.~;~:,t..:~" -,,!:I~,~';~~t , ,;j:~i, .' ~ GJNERAL SNOW I..THRQWJNG I.fi;r.:.";;,~~..:, '::J..~o.i:.:..- ""C ...
-
Yard-Man 7100-1 - page 4
UNPACKING AND SET-UP 3. Assemble handle panel assembly to the under side of right and left handle tubes and secure with four slotted hex head bolts and lock nuts. Tighten all bolts on the handle assembly. Place handle grips over ends of the handle tubes. 4. Assemble chute adjustment shaft through hole in the handle panel and into uni";'er ...
-
Yard-Man 7100-1 - page 5
BEFORE STARTING ENGINE ! 2. Place machine on a level surface. Remove oil fill cap and fill crankcase with good quality detergent oil. Use MS classification SAE 5W-20 oil for operation below 400 F. Use MS classification SAE 30 oil for operation above 400 F. 3. During initial "Break-in" period, the oil should be checked often. 4. Change oil ...
-
Yard-Man 7100-1 - page 6
OPERATION OF CONTROLS MASTER CLUTCH CONTROL FREE WHEELING The wheel clutches are located on wheels and are used to engage or disengage power to wheels. To free the wheels for pushing, pullout on the knob and turn to lock. To provide self-propelling power to the wheels turn clutches in the opposite direction and relea~. The wheel clutches are spring ...
-
Yard-Man 7100-1 - page 7
REPLACING SAFETY SHEAR BOLT CHUTE CHAIN AND ADJUSTMENT To tighten the chute chain, rotate the chute all the way to the left, until the adjustment bolt is accessible. Tighten the adjustment nut to tighten the chain. CAUTION: Chain should be kept snug on chute housing. CHUTE CABLE ADJUSTMENT ..~~. -..:."~,,-"..' .~.4n:",;.,_: ! ...
-
Yard-Man 7100-1 - page 8
...
-
Yard-Man 7100-1 - page 9
~ r oj ~ /' See pages 10 and 11 for parts list. 9 ...
-
Yard-Man 7100-1 - page 10
PARTS LIST MODEL 7100-1 Your SNOW THROWER is right hand (R.H.) or left hand (L.H.) as you operate mad1ine. REF. PART NO. NO. 1 1539-80 2 1658-29-40 3 41256 4 2119-49 5 3616-516 6 1538-30 7 40070 8 2643-51-40 9 1710-50-40 10 4712-99 11 1 !.Q9-1 39 12 1616-459 13 4712-98 14 40890 15 40149 16 40148 17 3-79 18 3609-433 19 41994 20 1605-582 21 1683-92 2 ...
-
Yard-Man 7100-1 - page 11
TRANSMISSION S '/" 7 8,9 ~ I " , /, ~. ., '0 0&0., -- : o;..~~ )0' ~ ~/ ) .~'l"~/20 '~ '...~ , ~-. ., / 2K .. f 23 ~. ».- ';' .." ~. ~ 22- : / / ; ..I ~'", ~. . REF. NO. 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 PART DESCRIPTION NO. 2632-175 Shaft -Hex 42180 N ...
-
Yard-Man 7100-1 - page 12
IDLER LINKAGE ADJUSTMENT Should the drive belt stretch sufficiently to cause the adjustment link to hang up in the bottom of the idler arm slot when the master clutch lever is in drive position, readjust as follows. To adjust, move master clutch to drive position, remove cotter pin from adjustment link, or bottom of rod, and thread link upon rod un ...
-
Yard-Man 7100-1 - page 13
LU BRICA TION CHANGING ENGINE OIL LUBRICATION POINTS lUBRICATE THE PARTS PERIODICAllY AS IllUS. TRATED. The following points are to be lubricated every five hours of operation with SAE 20 weight light duty oil, unless otherwise noted. 1. Spherical Bearings (Both Sides) 2. Wheels 3. Discharge Spout 4. Blower Housing 5. Reel Chain 6. Chute Adjustment ...
-
Yard-Man 7100-1 - page 14
CHUTE CABLE REPLACEMENT OR REPAIR cable roller bracket and down to the right hole in the top of the blower housing. C. Turn the cable pulley with the cable bolt toward the bottom of the blower housing. D. Put the ends of the cable up through the holes in the bottom of the cable pulley and cross the ends up and over the cable bolt and under the wash ...
-
Yard-Man 7100-1 - page 15
...
-
Yard-Man 7100-1 - page 16
M 26" SNOW THROWER ~ Yard-Man reserves the right to make engineering changes without prior notification or respon- sibility to the Purchaser. ~-~-~-~~~~ ~ ~-- ~ ;. -~-~-~-~-~-~ ~-~-~ ~ ~ ~ ,. 7171 We gu'arantee all parts again'st. defects' in material and workmanship .for a period of one (1) year from the date of purchase when u ...
Yard-Man 7100-1についてご質問がありますか？
次のフォームを使用してください
見つけた説明書を読んでもYard-Man 7100-1の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがYard-Man 7100-1で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。