Snapper 155223の取扱説明書

40ページ 2.51 mb
ダウンロード

ページに移動 of 40

Summary
  • Snapper 155223 - page 1

    Safety Instructions & Operator's Manual for TWO STAGE INTERMEDIATE FRAME SNOW THROWER SERIES 3 MODELS 155223 17243 MODEL NUMBER EXPLANATION MODEL DESIGNATION ENGINE HP II Iss122131 I I SERIES DESIGNATION AUGER WIDTH I - Intermediate Frame Model 55 - 5.5 Engine HP (Engine Horse Power) 7 - 7.0 Engine HP (Engine Horse Power) 22 - 22" Aug ...

  • Snapper 155223 - page 2

    IMPORTANT SAFETY INSTRUCTIONS WARNING: This powerful machine is capable of amputating hands and feet and can throw objects that can cause injury and damage! Failure to comply with the following instructions may result in serious injury to the operator or other persons. The owner of the snow thrower must understand these instructions and, furthermor ...

  • Snapper 155223 - page 3

    IMPORTANT SAFETY INSTRUCTIONS OPERATIONAL PRECAUTIONS (Continued From Previous Page) 7. DO NOT put hands or feet near or under rotating parts. Keep clear of the discharge opening at all times. 8. Start engine only where exhaust fumes will be safely dissipated. Allow a brief warm-up period, and practice operation of controls outside before putting t ...

  • Snapper 155223 - page 4

    TABLE OF CONTENTS SECTION 1 - IMPORTANT SAFETY INSTRUCTIONS .......................... 2-3 TABLE OF CONTENTS ............................................................................ 4 SECTION 2 - OPERATING INSTRUCTIONS ......................................... 5-9 Pre-start Checklist ............................................................. ...

  • Snapper 155223 - page 5

    Section 2 - OPERATING INSTRUCTIONS 2.1 PRE-START CHECK LIST Make the following checks and perform the service required before each start-up. 2.1.1. Check engine oil and add oil as needed to bring level up to the FULL mark. Refer to engine owner's manual for oil specifications 2.1.2. Check guards, chutes, deflectors and covers to make sure all ...

  • Snapper 155223 - page 6

    Section 2 - OPERATING INSTRUCTIONS 2.2 STARTING, OPERATION & STOPPING (RECOIL START MODELS) (Go to Page 8 for Electric Start Models) 2.2.1. ENGINE 1. Turn fuel shut off valve to the "ON" position. See Figure 2.3. TURN VALVE TO "ON" POSITION FIGURE 2.3 2. Insert key into ignition switch. See Figure 2.4. 3. Move choke control ...

  • Snapper 155223 - page 7

    Section 2 - OPERATING INSTRUCTIONS Objects can be thrown by the snow thrower while it is in operation. Thrown objects could cause serious injury to the operator or bystanders. Always wear safety goggles or other suitable eye protection. Keep people and pets away from area. 2.2.3. ENGAGING AUGER 1. Move auger control lever against handle to engage a ...

  • Snapper 155223 - page 8

    Section 2 - OPERATING INSTRUCTIONS 2.2 STARTING, OPERATION & STOPPING (ELECTRIC START MODELS) (Go to Page 6 for Recoil Start Models) DO NOT use an electrical extension cord that is damaged. A damaged electrical extension cord could cause a shock or fire. Thoroughly inspect electrical extension cord before using machine. If cord is damaged, do n ...

  • Snapper 155223 - page 9

    Section 2 - OPERATING INSTRUCTIONS WARNING Objects can be thrown by the snow thrower while it is in operation. Thrown objects could cause serious injury to the operator or bystanders. Always wear safety goggles or other suitable eye protection. Keep people and pets away from area. 2.2.9. ENGAGING AUGER 1. Pull auger control lever against handle to ...

  • Snapper 155223 - page 10

    Section 3 - MAINTENANCE DO NOT attempt any adjustments, maintenance, service, or repairs, with engine running. Stop auger. Stop engine. Remove key. Disconnect spark plug wire and secure wire away from spark plug. 3.1 INTRODUCTION To retain the quality of the snow thrower, use only genuine SNAPPER replacement parts. Contact a local SNAPPER dealer fo ...

  • Snapper 155223 - page 11

    Section 3 - MAINTENANCE 3.4 ANNUALLY (END OF EACH SEASON) Perform all maintenance as described in the maintenance schedule. 3.4.1. Engine Refer to engine owner's manual for service instructions. 3.4.2. Spark Plug Refer to engine owner's manual for service instructions. 3.5 STORAGE PROCEDURE Refer to the Engine Owner's Manual for dire ...

  • Snapper 155223 - page 12

    Section 4 - REPAIR & ADJUSTMENTS DO NOT attempt any adjustments, maintenance, service, or repairs, with engine running. Stop auger. Stop engine. Remove key. Disconnect spark plug wire and secure wire away from spark plug. 4.1 AUGER and WHEEL DRIVE BELT ADJUSTMENT/REPLACEMENT When operating machine release the auger clutch control. The auger sho ...

  • Snapper 155223 - page 13

    Section 4 - REPAIR & ADJUSTMENTS WARNING DO NOT attempt any adjustments, maintenance, service, or repairs, with engine running. Stop auger. Stop engine. Remove key. Disconnect spark plug wire and secure wire away from spark plug. Before tilting machine, drain all the fuel from fuel tank. Allow engine to run, outdoors where fumes can be safely d ...

  • Snapper 155223 - page 14

    Section 4 - REPAIR & ADJUSTMENTS WARNING DO NOT attempt any adjustments, maintenance, service, or repairs, with engine running. Stop auger. Stop engine. Remove key. Disconnect spark plug wire and secure wire away from spark plug. Before tilting machine, drain all the fuel from fuel tank. Allow engine to run, outdoors where fumes can be safely d ...

  • Snapper 155223 - page 15

    Section 4 - REPAIR & ADJUSTMENTS 4.1.5. GROUND SPEED ADJUSTMENT NOTE: It is recommended to remove the drive system cover and check rubber drive tire engagement with drive disc when adjusting ground speed. 1. Tilt machine forward to gain access to drive system area. Secure machine in the tilted position to prevent tipping over. Remove drive syst ...

  • Snapper 155223 - page 16

    Section 4 - REPAIR & ADJUSTMENTS 4.1.8. SINGLE HANDLE CONTROL ADJUSTMENT (7 HP Models Only) IMPORTANT: Standing in the operator's position, the left handle bar lever is for wheel drive engagement and disengagement. The right handle bar lever is for auger/impeller engagement and disengagement. Hold both levers down to handle bar for engagem ...

  • Snapper 155223 - page 17

    Section 4 - REPAIR & ADJUSTMENTS WARNING DO NOT attempt any adjustments, maintenance, service, or repairs, with engine running. Stop auger. Stop engine. Remove key. Disconnect spark plug wire and secure wire away from spark plug. Before tilting machine, drain all the fuel from fuel tank. Allow engine to run, outdoors where fumes can be safely d ...

  • Snapper 155223 - page 18

    PROBLEM Engine Will Not Start Using Recoil Starter Engine Will Not Start Using Electric Starter Engine Stalls or Stops After Running Engine Loses Power Excessive Vibration Poor Snow Discharging TROUBLESHOOTING 1. 2. 3. 4. 1 2. 3. 1 2. 3. 4. 5. 1 2. 3. 1 2. PROBABLE CAUSE Fuel tank empty• 1. Engine needs choking and priming• 2. Spark plug wire d ...

  • Snapper 155223 - page 19

    3 YEAR LIMITED WARRANTY For three (3) years from purchase date for the original purchaser's residential, non-commercial use, SNAPPER, through any authorized SNAPPER dealer will replace, free of charge (except for taxes where applicable), any part or parts found upon examination by the factory at McDonough, Georgia, to be defective in material ...

  • Snapper 155223 - page 20

    Safety Instructions & Operator's Manual for TWO STAGE INTERMEDIATE FRAME SNOW THROWER SERIES 3 ® IMPORTANT Snapper products are built using engines that meet or exceed all applicable emissions requirements on the date manufactured. The labels on those engines contain very important emissions information and critical safety warnings. Read, ...

  • Snapper 155223 - page 21

    Safety Instructions & Operator's Manual for TWO STAGE INTERMEDIATE FRAME SNOW THROWER SERIES 3 MODELS 155223 17243 MODEL NUMBER EXPLANATION MODEL DESIGNATION ENGINE HP II Iss122131 I I SERIES DESIGNATION AUGER WIDTH I - Intermediate Frame Model 55 - 5.5 Engine HP (Engine Horse Power) 7 - 7.0 Engine HP (Engine Horse Power) 22 - 22" Aug ...

  • Snapper 155223 - page 22

    IMPORTANT SAFETY INSTRUCTIONS WARNING: This powerful machine is capable of amputating hands and feet and can throw objects that can cause injury and damage! Failure to comply with the following instructions may result in serious injury to the operator or other persons. The owner of the snow thrower must understand these instructions and, furthermor ...

  • Snapper 155223 - page 23

    IMPORTANT SAFETY INSTRUCTIONS OPERATIONAL PRECAUTIONS (Continued From Previous Page) 7. DO NOT put hands or feet near or under rotating parts. Keep clear of the discharge opening at all times. 8. Start engine only where exhaust fumes will be safely dissipated. Allow a brief warm-up period, and practice operation of controls outside before putting t ...

  • Snapper 155223 - page 24

    TABLE OF CONTENTS SECTION 1 - IMPORTANT SAFETY INSTRUCTIONS .......................... 2-3 TABLE OF CONTENTS ............................................................................ 4 SECTION 2 - OPERATING INSTRUCTIONS ......................................... 5-9 Pre-start Checklist ............................................................. ...

  • Snapper 155223 - page 25

    Section 2 - OPERATING INSTRUCTIONS 2.1 PRE-START CHECK LIST Make the following checks and perform the service required before each start-up. 2.1.1. Check engine oil and add oil as needed to bring level up to the FULL mark. Refer to engine owner's manual for oil specifications 2.1.2. Check guards, chutes, deflectors and covers to make sure all ...

  • Snapper 155223 - page 26

    Section 2 - OPERATING INSTRUCTIONS 2.2 STARTING, OPERATION & STOPPING (RECOIL START MODELS) (Go to Page 8 for Electric Start Models) 2.2.1. ENGINE 1. Turn fuel shut off valve to the "ON" position. See Figure 2.3. TURN VALVE TO "ON" POSITION FIGURE 2.3 2. Insert key into ignition switch. See Figure 2.4. 3. Move choke control ...

  • Snapper 155223 - page 27

    Section 2 - OPERATING INSTRUCTIONS Objects can be thrown by the snow thrower while it is in operation. Thrown objects could cause serious injury to the operator or bystanders. Always wear safety goggles or other suitable eye protection. Keep people and pets away from area. 2.2.3. ENGAGING AUGER 1. Move auger control lever against handle to engage a ...

  • Snapper 155223 - page 28

    Section 2 - OPERATING INSTRUCTIONS 2.2 STARTING, OPERATION & STOPPING (ELECTRIC START MODELS) (Go to Page 6 for Recoil Start Models) DO NOT use an electrical extension cord that is damaged. A damaged electrical extension cord could cause a shock or fire. Thoroughly inspect electrical extension cord before using machine. If cord is damaged, do n ...

  • Snapper 155223 - page 29

    Section 2 - OPERATING INSTRUCTIONS WARNING Objects can be thrown by the snow thrower while it is in operation. Thrown objects could cause serious injury to the operator or bystanders. Always wear safety goggles or other suitable eye protection. Keep people and pets away from area. 2.2.9. ENGAGING AUGER 1. Pull auger control lever against handle to ...

  • Snapper 155223 - page 30

    Section 3 - MAINTENANCE DO NOT attempt any adjustments, maintenance, service, or repairs, with engine running. Stop auger. Stop engine. Remove key. Disconnect spark plug wire and secure wire away from spark plug. 3.1 INTRODUCTION To retain the quality of the snow thrower, use only genuine SNAPPER replacement parts. Contact a local SNAPPER dealer fo ...

  • Snapper 155223 - page 31

    Section 3 - MAINTENANCE 3.4 ANNUALLY (END OF EACH SEASON) Perform all maintenance as described in the maintenance schedule. 3.4.1. Engine Refer to engine owner's manual for service instructions. 3.4.2. Spark Plug Refer to engine owner's manual for service instructions. 3.5 STORAGE PROCEDURE Refer to the Engine Owner's Manual for dire ...

  • Snapper 155223 - page 32

    Section 4 - REPAIR & ADJUSTMENTS DO NOT attempt any adjustments, maintenance, service, or repairs, with engine running. Stop auger. Stop engine. Remove key. Disconnect spark plug wire and secure wire away from spark plug. 4.1 AUGER and WHEEL DRIVE BELT ADJUSTMENT/REPLACEMENT When operating machine release the auger clutch control. The auger sho ...

  • Snapper 155223 - page 33

    Section 4 - REPAIR & ADJUSTMENTS WARNING DO NOT attempt any adjustments, maintenance, service, or repairs, with engine running. Stop auger. Stop engine. Remove key. Disconnect spark plug wire and secure wire away from spark plug. Before tilting machine, drain all the fuel from fuel tank. Allow engine to run, outdoors where fumes can be safely d ...

  • Snapper 155223 - page 34

    Section 4 - REPAIR & ADJUSTMENTS WARNING DO NOT attempt any adjustments, maintenance, service, or repairs, with engine running. Stop auger. Stop engine. Remove key. Disconnect spark plug wire and secure wire away from spark plug. Before tilting machine, drain all the fuel from fuel tank. Allow engine to run, outdoors where fumes can be safely d ...

  • Snapper 155223 - page 35

    Section 4 - REPAIR & ADJUSTMENTS 4.1.5. GROUND SPEED ADJUSTMENT NOTE: It is recommended to remove the drive system cover and check rubber drive tire engagement with drive disc when adjusting ground speed. 1. Tilt machine forward to gain access to drive system area. Secure machine in the tilted position to prevent tipping over. Remove drive syst ...

  • Snapper 155223 - page 36

    Section 4 - REPAIR & ADJUSTMENTS 4.1.8. SINGLE HANDLE CONTROL ADJUSTMENT (7 HP Models Only) IMPORTANT: Standing in the operator's position, the left handle bar lever is for wheel drive engagement and disengagement. The right handle bar lever is for auger/impeller engagement and disengagement. Hold both levers down to handle bar for engagem ...

  • Snapper 155223 - page 37

    Section 4 - REPAIR & ADJUSTMENTS WARNING DO NOT attempt any adjustments, maintenance, service, or repairs, with engine running. Stop auger. Stop engine. Remove key. Disconnect spark plug wire and secure wire away from spark plug. Before tilting machine, drain all the fuel from fuel tank. Allow engine to run, outdoors where fumes can be safely d ...

  • Snapper 155223 - page 38

    PROBLEM Engine Will Not Start Using Recoil Starter Engine Will Not Start Using Electric Starter Engine Stalls or Stops After Running Engine Loses Power Excessive Vibration Poor Snow Discharging TROUBLESHOOTING 1. 2. 3. 4. 1 2. 3. 1 2. 3. 4. 5. 1 2. 3. 1 2. PROBABLE CAUSE Fuel tank empty• 1. Engine needs choking and priming• 2. Spark plug wire d ...

  • Snapper 155223 - page 39

    3 YEAR LIMITED WARRANTY For three (3) years from purchase date for the original purchaser's residential, non-commercial use, SNAPPER, through any authorized SNAPPER dealer will replace, free of charge (except for taxes where applicable), any part or parts found upon examination by the factory at McDonough, Georgia, to be defective in material ...

  • Snapper 155223 - page 40

    Safety Instructions & Operator's Manual for TWO STAGE INTERMEDIATE FRAME SNOW THROWER SERIES 3 ® IMPORTANT Snapper products are built using engines that meet or exceed all applicable emissions requirements on the date manufactured. The labels on those engines contain very important emissions information and critical safety warnings. Read, ...

メーカー Snapper カテゴリー Snow Blower

Snapper 155223のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 155223の取扱説明書
- Snapperの製品カード
- パンフレット
- またはSnapper 155223の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Snapper 155223の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Snapper 155223の取り付け説明書、サービスマニュアル、簡易説明書、またはSnapper 155223のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Snapper 155223の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Snapper 155223デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがSnapper 155223を使用するのを助ける技術的文書のことです。説明書は通常、全てのSnapper 155223ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Snapperの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Snapper 155223の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははSnapper 155223の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Snapper 155223に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Snapper 155223デバイスの基本機能を使うにあたってのヒント。 Snapper 155223のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Snapper 155223に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるSnapper 155223のメーカー/サービスへの連絡先に関する情報。

Snapper 155223についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもSnapper 155223の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがSnapper 155223で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)