日本語 dropdown-ico

Craftsman 247.77588Oの取扱説明書

26ページ 1.03 mb
ダウンロード

ページに移動 of 26

Summary
  • Craftsman 247.77588O - page 1

    Owner's Manual CRAFTSMAN 8.5 Horse Power CHIPPER-SHREDDER Model No. 247.77588O CAUTION: Before using this product, read this manual and follow all Safety Rules and Operating Instructions. Sears, Roebuck and Co., Hoffman Estates, IL 60179, U.S.A. 770-1228A Printed in U.S.A. (3/98) ...

  • Craftsman 247.77588O - page 2

    Content Page Content Page Warranty Information 2 Service & Adjustment 14 Safe Operation Practices 3 Off-Season Storage 16 Assembly 5 Trouble-Shooting 17 Operation 8 Repair Parts 18 Maintenance 11 One-Year Warranty on Craftsman Chipper-Shredder For one year from the date of purchase, when this Craftsman chipper-shredderis maintained, lubricated, ...

  • Craftsman 247.77588O - page 3

    This symbol points out important safety instructions which, if not followed, could endanger the per- sonal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate your chipper shredder. Failure to comply with these instructions may result in per- sonal injury.When you see this symb ...

  • Craftsman 247.77588O - page 4

    impeller tocome toa complete stop. The impeller continues torotate for a few seconds after the engine is shut off. Never place any part of the body in the impeller area untilyou are sure the impeller has stopped rotating. Muffler and engine become hot and can cause a bum. Do not touch. Do not allow leaves or other debris to build-up on engine' ...

  • Craftsman 247.77588O - page 5

    Hopper* Chipper Chute Discharge Chute Bottle of Oil Safety Glasses Catcher Bag * The hopper is packed in the top insert in your chipper-shredder carton. Figure 1 IMPORTANT: This unit is shipped without gasoline or oil in the engine, Al_er assembly, see OPERATION section of this manual for proper fuel and engine oil fill-up. NOTE: To determine right ...

  • Craftsman 247.77588O - page 6

    through hinge on discharge chute and housing (spacer fits inside of hinge). See figure 3 inset. Spac_er _-J-_ Hex Nut --Hex Bolt Hinge Hopper Pivot Door Inlet Guide Opening He_ Hopper Nut Wing Dischargl Figure 3 Place second spacer over hex bolt inside the other part of the hinge. Secure with hex lock nut. Tighten securely. Secure both sides of d ...

  • Craftsman 247.77588O - page 7

    & WARNING; This flap control rod is a safety device to hold the flap in place inside the hopper while shredding branches. Do not operate the chipper-shredder without properly attachingthis flap control rod to the unit. Stop Hex Washer* Nut* // =ett I / io_ Chipper Chute Insert one each of the hex bolts,lock nuts, and flat washers (that you ...

  • Craftsman 247.77588O - page 8

    Read this owner's manual and safety rules before operating your chipper-shredder. Compare the illustration in figure 9 with your chipper-shredder to familiarize yourselfwith the location of various controls and adjustments. Save this manual for future reference. _ he operation of any chipper-shredder can result in foraign objects being thrown ...

  • Craftsman 247.77588O - page 9

    WARNING: Before using yourchipper- shredder, again refer to the safety rules on pages 3 and 4 of this manual. Always be careful. GAS AND OIL FILL-UP Oil (Packed with unit) Only use high quality detergent oil rated with API service classification SF, SG or SH. Select the oil's viscosity grade accordingto your expected operating temperature. Fol ...

  • Craftsman 247.77588O - page 10

    NOTE: TO prevent the unit fromsliding, place your foot firmly against the tire. 1. Attach spark plug wire -- 3. Move choke to "on" position 2. Place throttle in Fast Position 4. Pull rope Figure 1t Attach spark plug wire and rubber boot to spark plug. See figure 11. Place throttle in FAST position. See figure 11. Move choke lever to CHO ...

  • Craftsman 247.77588O - page 11

    changes (becomes stdngy, etc.) or if the rate at which the material is discharged slows down considerably, it is likely that the shredding blade and/or chipper blades are dull and need to be sharpened or replaced. Refer to Service and Adjustments section. IMPORTANT: There is a flail screen located inside the housing in the discharge area. If the fl ...

  • Craftsman 247.77588O - page 12

    CUSTOMER RESPONSIBILITIES o MAINTENANCE _ _ ..,P e,_P _3 =_ sc. oo, o,O { o ,v.C o,TEs Oil pivot points 0 Clean shredder _ a. Check engine oil ,,, Change engine oil <_ Service air cleaner ILl Clean engine _ Reset spark plug _ Clean muffler operatingtemperature. Refer to page 9 of this To Service Air Cleaner: manual for viscosity chart. 1. The fo ...

  • Craftsman 247.77588O - page 13

    If necessary, replace paper filter (do not attempt to clean). Installnew filter on base. Slide pre-cleaner over filter. Install cover and wing nut. Tighten wing nut securely. Clean Engine Clean engine periodically. Remove dirt and debris with a cloth or brush. Frequently remove grass clippings, dirt and debris from cooling fins, air intake screen a ...

  • Craftsman 247.77588O - page 14

    14 ...

  • Craftsman 247.77588O - page 15

    REMOVING THE FLAIL SCREEN If the discharge area becomes clogged, remove the flail screen and clean area as follows. Stop engine, make certain the chipper- shredder has come to a complete stop and disconnect spark plug wire from the spark plug before unclogging the chute. Remove the two hand knobs on each side of the discharge chute (also called the ...

  • Craftsman 247.77588O - page 16

    Disconnect spark plug wire and move it away from spark plug. Lower the hopper assembly. Block up the housing. See figure 19. Weld Bolt Allen Screw Pipe cause damage to the unit.The blade can be tasted for balance by balancing it on a round shaft screwddver or nail. Removemetal from the heavy side untilit is balanced evenly. See figure 20. When reas ...

  • Craftsman 247.77588O - page 17

    Prepare your chipper-shredder for storage at the end of the season or if the unit will not be used for 30 days or more. A WARNING: Never store machine with fuel in the fuel tank inside of building where fumes may reach an open flame or spark, or where ignition sources are present such as hot water end space heaters, furnaces, clothes dryers, stoves ...

  • Craftsman 247.77588O - page 18

    PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION Engine fails to start 1. Fuel tank empty, orstale fuel 1. Fill tank with clean, fresh fuel 2. Spark plug wire disconnected 2. Connect wire to spark plug. 3. Faulty spark plug 3. Clean, adjust gap or replace. 4. Throttle control not in correct 4. Move throttlecontrol to FAST position position Loss of power; o ...

  • Craftsman 247.77588O - page 19

    SEARS CRAFTSMAN 8.5 H.P. CHIPPER-SHREDDER MODEL 247.775880 6 29 12 21 5 14 18 97 33 13 74 52 56 85 88 63 65 80 79 91 19 ...

  • Craftsman 247.77588O - page 20

    Key Part No No -- 770-1228A 1 11480 2 681-0118 3 681-0144 4 710-0542 710-0607 710-3256 7 712-0429 8 712-3027 9 714-0104 10 715-0129 11 726-0106 12 726-0135 13 728-0175 14 732-0546 15 732-0629 16 735-0127 17 735-0651 18 736-0119 19 738-0137A 20 738-0946 21 747-0531A 22 747-0747 23 747-1124 124 747-1125 ,25 781-0492A 126 781-0633 27 781-0698 28 781-0 ...

  • Craftsman 247.77588O - page 21

    SEARS CRAFTSMAN 8.5 H.P. ENGINE MODEL 143.988503 FOR CHIPPER-SHREDDER MODEL 247.775880 35 4OO 310 3O5 757 87 7O 69 2g0 101 1t0 182 251 21 ...

  • Craftsman 247.77588O - page 22

    SEARS CRAFTSMAN 8.5 H.P. ENGINE MODEL 143.988503 FOR CHIPPER-SHREDDER MODEL 247,775880 Key Part No. No. -- m 1 35385 2 27652 4 5 30969 15 30699C 15A 17 18 19 20 25 26 28 30 35 38 37 38 40 40 41 41 42 42 43 45 47 48 49 5O 60 65 69 70 71 72 75 30700 650494 33454 29916 651028 34663 35319 36460 650561 30322 36283A 29826 29918 29216 29642 40011 40012 40 ...

  • Craftsman 247.77588O - page 23

    SEARS CRAFTSMAN 8.5 H.P. ENGINE MODEL 143.988503 FOR CHIPPER-SHREDDER MODEL 247,775880 Key Part No. No. 185 34707 186 34667 200 34677 203 31342 204 651029 206 610973 207 33878 209 650821 215 35882 223 650378 224 27915A 238 28820 239 27272A 240 37104 242 33267 245 33268 245A 35881 250 33269A 251 650513 260 36250 261 650788 262 29747B 264A 650802 265 ...

  • Craftsman 247.77588O - page 24

    SEARS CRAFTSMAN 8.5 H.P. ENGINE MODEL 143.988503 FOR CHIPPER-SHREDDER MODEL 247.775880 Carburetor Key Part Description No. No. 640112 1 631776A 2 631970 4 631184 ,._ 5 631183 11 6 64O109 _12 7 650506 i 10 632740 "15 13 11 632043 // 12 631184 13 631183 14 631753 15 630735 16 632164 17 651025 18 630766 20 640027 20A 64O053 25 631867 27 631024 28 ...

  • Craftsman 247.77588O - page 25

    SEARS CRAFTSMAN 8.5 H.P. ENGINE MODEL 143.988503 FOR CHIPPER-SHREDDER MODEL 247.775880 Recoil Starter 590746 13 12 "8 6_'_6 ¢p-.4 Key Part Description No. No. 590746 1 590599A 2 590600 3 590679 4 590601 5 590678 6 590680 7 590412 8 590681 11 590747 12 590535 13 590701 Recoil Starter Spring Pin (Incl. 4) Washer Retainer Washer Brake Sprin ...

  • Craftsman 247.77588O - page 26

    For the repair or replacement partsyou need delivered directlyto your home Call 7 am - 7 pm, 7 days a week 1-800-366-PART (1-800-366-7278) For in-home major brand repair service Call 24 hours a day, 7 days a week 1-8OO-4-REPAIR (1-800-473-7247) For the location of a Sears Parts and Repair Center in your area Call 24 hours a day, 7 days a week 1-800 ...

メーカー Craftsman カテゴリー Chipper

Craftsman 247.77588Oのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 247.77588Oの取扱説明書
- Craftsmanの製品カード
- パンフレット
- またはCraftsman 247.77588Oの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Craftsman 247.77588Oの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Craftsman 247.77588Oの取り付け説明書、サービスマニュアル、簡易説明書、またはCraftsman 247.77588Oのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Craftsman 247.77588Oの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Craftsman 247.77588Oデバイスの取扱説明書はどのようなものですか？
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがCraftsman 247.77588Oを使用するのを助ける技術的文書のことです。説明書は通常、全てのCraftsman 247.77588Oユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Craftsmanの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Craftsman 247.77588Oの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははCraftsman 247.77588Oの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Craftsman 247.77588Oに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Craftsman 247.77588Oデバイスの基本機能を使うにあたってのヒント。 Craftsman 247.77588Oのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Craftsman 247.77588Oに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるCraftsman 247.77588Oのメーカー/サービスへの連絡先に関する情報。

Craftsman 247.77588Oについてご質問がありますか？

次のフォームを使用してください

見つけた説明書を読んでもCraftsman 247.77588Oの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがCraftsman 247.77588Oで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

Captcha
新しい画像

コメント (0)