Zenoah RMSZ2500の取扱説明書

36ページ 1.28 mb
ダウンロード

ページに移動 of 36

Summary
  • Zenoah RMSZ2500 - page 1

    OWNER / OPERA T OR MANUAL SWEEPER RMS9-99102 (501) The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. W ARNING Before using our products, please read this manual carefully to understand the proper use of your unit. W ARNING DRIVE UNIT 900101 and up SWEE ...

  • Zenoah RMSZ2500 - page 2

    ...

  • Zenoah RMSZ2500 - page 3

    SAFETY FIRST Instructions contained in warnings within this manual marked with a symbol concern critical points which must be taken into consideration to prevent possible serious bodily injury, and for this reason you are requested to read all such instructions carefully and follow them without fail. ■ WARNINGS IN THE MANUAL This mark indicates i ...

  • Zenoah RMSZ2500 - page 4

    1. Parts location  4  1. Loop Handle 2. Shoulder Strap Hanger 3. Ignition Switch 4. Throttle Cable 5. Throttle Lever 6. Throttle set Button 7. Drive shaft Housing 8. Drum Ass’y 9. Sweeper Belt 10. Spark Arrester 11. Starter Knob 12. Fuel Tank 13. Primer Pump 14. Choke Lever 15. Air Cleaner Cover ...

  • Zenoah RMSZ2500 - page 5

    2. Specifications ■ RMSZ2500 Overall Size(LxWxH) ························································ 70.5(1790)x27(686)x12.2(310) in(mm) Dry Weight ·····································································? ...

  • Zenoah RMSZ2500 - page 6

    (1) Read owner's manual before operating this machine. (2) Wear head, eye and ear protection. (3) Warning/Attention (4) Keep all children, bystanders and helpers 15 meters away from the unit If warning label peel off or become soiled and impossible to read, you should contact the dealer from which you purchased the product to order new labels ...

  • Zenoah RMSZ2500 - page 7

    For safe operation and maintenance, symbols are carved in relief on the machine. According to these indications, please be careful not to take a mistake. (a) The port to refuel the "MIX GASOLINE" Position: FUEL TANK CAP (b) The direction to close the choke Position: AIR CLEANER COVER (c) The direction to open the choke Position: AIR CLEAN ...

  • Zenoah RMSZ2500 - page 8

     8  5. For safe operation 1. Read this manual carefully until you completely understand and follow all safety and operating instructions. 2. Keep this manual handy so that you may refer to it later whenever any questions arise. Also note, if you have any questions which cannot be answered herein, contact the dealer from whom you purchased the ...

  • Zenoah RMSZ2500 - page 9

     9  b. At night, at times of heavy fog, or at any other times when your field of vision might be limited and it would be difficult to gain a clear view of the working area. c. During rain storms, during lightning storms, at times of strong or gale-force winds, or at any other times when weather conditions might make it unsafe to use the produ ...

  • Zenoah RMSZ2500 - page 10

     10  ■ BEFORE STARTING THE ENGINE 1. The area within a perimeter of 50 feet (15m) of the person using the product should be considered a hazardous area into which no one should enter. If necessary yellow warning rope, warning signs should be placed around the perimeter of the area. When work is to be performed simultaneously by two or more ...

  • Zenoah RMSZ2500 - page 11

     11  Never place the throttle into the high speed position when starting the engine. 3. After starting the engine, check to make sure that the Drum Ass’y stops rotating when the throttle is moved fully back to its original position. If it continues to rotate even after the throttle has been moved fully back, turn off the engine and take the ...

  • Zenoah RMSZ2500 - page 12

     12  • IF SOMEONE COMES 1. Guard against hazardous situations at all times. Warn adults to keep pets and children away from the area. Be careful if you are approached. Injury may result from flying debris. 2. If someone calls out or otherwise interrupts you while working, always be sure to turn off the engine before turning around. ■ MAIN ...

  • Zenoah RMSZ2500 - page 13

     13  5. For safe operation refill the tank of the unit in any place where there is a boiler, stove, wood fire, electrical sparks, welding sparks, or any other source of heat or fire which might ignite the fuel. 2. Never smoke while operating the unit or refilling its fuel tank. 3. When refilling the tank, always turn off the engine and allow ...

  • Zenoah RMSZ2500 - page 14

    ■ MOUNTING ENGINE (SE1) 1. Push the driveshaft housing toward the clutch housing and rotate it by hand to check that the driveshaft is engaged with the gears. 2. Insert the driveshaft housing into the clutch housing until it bottoms, and align the positioning holes on the clutch housing and the shaft tube and install the screw. When difficult to ...

  • Zenoah RMSZ2500 - page 15

    6. Set up  15  SE4 ■ SWEEPER ASSEMBLY (SE4) 1. Push one of the drum axles onto either of the two gearcase output shafts. If necessary, rotate the drum axle until the clevis pin hole in the axle aligns with the matching hole in the gearcase output shaft. 2. Use a clevis pin and hitch pin to secure the drum axel to the shaft. 3. Slide the rec ...

  • Zenoah RMSZ2500 - page 16

     16  7. Fuel ■ RECOMMENDED MIXING RATIO GASOLINE 50:OIL 1 • Exhaust emission are controlled by the fundamental engine parameters and components(eq., carburation, ignition timing and port timing) without addition of any major hardware or the introduction of an inert material during combustion. • These engines are certified to operate on ...

  • Zenoah RMSZ2500 - page 17

    7. Fuel  17  again for at least one minute. As some oils may be difficult to agitate depending on oil ingredients, sufficient agitation is necessary for the engine to last long. Be careful that, if the agitation is insufficient, there is an increased danger of early piston seizing due to abnormally lean mixture. 5. Put a clear indication on t ...

  • Zenoah RMSZ2500 - page 18

     18  ■ STARTING ENGINE The cutting head will start rotating upon the engine starts. 1. Rest the unit on a flat, firm place. Keep the cutting head off the ground and clear of surrounding objects as it will start rotating upon starting of the engine. 2. Push the primer pump several times until overflown fuel flows out in the clear tube. (OP1) ...

  • Zenoah RMSZ2500 - page 19

    8. Operation ■ STOPPING ENGINE (OP3) 1. Release the throttle lever and run the engine for a half minute. 2. Shift the ignition switch to the STOP position. • Except for an emergency, avoid stopping the engine while pulling the throttle lever. ■ ADJUSTING THROTTLE CABLE • The normal play is 1 or 2mm when measured at the carburetor side end. ...

  • Zenoah RMSZ2500 - page 20

    • The RedMax Sweeper works best when its rubber fins can quickly slide or "skim" over the surface being swept. • New or replacement sweeper belts tend to grip or drag on hard surfaces, and should be thoroughly broken in or "scuffed" before the broom is actually put to work. • Break-in is easily accomplished by operating th ...

  • Zenoah RMSZ2500 - page 21

    8. Operation  21  • For long-term inverted operation, loosen the adjustment knob to reverse the handle. (OP10) (1) Adjustment Knob Reversing the RedMax Sweeper will cause debris to be thrown back toward the operator. When reversing the RedMax Sweeper, use lower throttle settings and beware that thrown debris may also affect your footing! ? ...

  • Zenoah RMSZ2500 - page 22

     22  8. Operation a load! • Doing so could damage the engine. Avoid low rpm operation • Continuous low-rpm operation can lead to premature clutch failure. ■ GENERAL SAFETY INSTRUCTIONS Work Safely The operator or bystanders can be injured if the RedMax Sweeper is misused or abused. Never allow a person without training or instruction to ...

  • Zenoah RMSZ2500 - page 23

    every every every every 25 40 50 100 system/compornent procedure before hours hours hours hours note use after after after after fuel leaks, fuel spillage wipe out ✔ fuel tank, air filter, fuel filter inspect/clean ✔✔ replace, if necessary see ■ ADJUSTING replace carburetor idle adjusting screw ✔ IDLING SPEED (p.19) if necessary clean and ...

  • Zenoah RMSZ2500 - page 24

     24  9. Maintenance MA1 1. Remove the drum and axle assemblies (see page 13), and then remove the four end cap bolts and the end cap (the gearcase need not be removed from the RedMax Sweeper). 2. Allow all used gearcase oil to drain into a small container. BURN DANGER! The gearcase and oil will be extremely hot after use! 3. Place the RedMax ...

  • Zenoah RMSZ2500 - page 25

    •M ake sure that the engine has stopped and is cool before performing any service to the machine. Contact with moving cutting head or hot muffler may result in a personal injury. ■ AIR FILTER • The air filter, if clogged, will reduce the engine performance. Check and clean the filter element in warm, soapy water as required. Dry completely be ...

  • Zenoah RMSZ2500 - page 26

     26  ■ MUFFLER • Inspect periodically, the muffler for loose fasteners, any damage or corrosion. If any sign of exhaust leakage is found, stop using the machine and have it repaired immediately. • Note that failing to do so may result in the engine catching on fire. ■ SPARK ARRESTER • The muffler is equipped with a spark arrester to ...

  • Zenoah RMSZ2500 - page 27

    9. Maintenance waste which has attached itself to the sweeper. Note that it is necessary to remove the engine cover shown in (MA6) in order to be able to view the upper part of the cylinder. • If waste gets stuck and causes blockage around the intake air cooling vent or between the cylinder fins, it may cause the engine to overheat, and that in t ...

  • Zenoah RMSZ2500 - page 28

    11 . T roubleshooting guide Case 1. Starting failure CHECK PROBABLE CAUSES ACTION fuel tank ➞ incorrect fuel ➞ drain it and with correct fuel fuel filter ➞ fuel filter is clogged ➞ clean carburetor adjustment screw ➞ out of normal range ➞ adjust to normal range sparking (no spark) ➞ spark plug is fouled/wet ➞ clean/dry ➞ plug gap ...

  • Zenoah RMSZ2500 - page 29

     29  12. Parts list NOTE : 1. Use KOMATSU ZENOAH genuine parts as specified in the parts list for repair and/or replacement. 2. KOMATSU ZENOAH does not warrant the machines, which have been damaged by the use of any parts other than those specified by the company. 3. When placing parts orders for repair and/or replacement, check if the model ...

  • Zenoah RMSZ2500 - page 30

     30  12. Parts list Fig.1 SHAFT GROUP (S/N 900101 and up) Fig.2 SWEEPER GROUP (S/N 000000 and up) Fig.3 ACCESSORY GROUP (S/N 000000 and up) RMSZ2500 ...

  • Zenoah RMSZ2500 - page 31

    Key# Description Part Number Q'ty 1P IPE COMP. T3074-12110 1 2 SHAFT 3074-12210 1 3 GRIP 3577-32141 1 4L EVER COMP. T3002-12200 1 5• CORD (A) T3002-12220 1 6• CORD (B) T3002-12230 1 7• TUBE T3002-12240 1 8• CABLE T3002-83100 1 9 PLATE-NAME RMS9-99001 1 10 PLATE 6425-12552 1 Key# Description Part Number Q'ty 11 TOOL-SET T3002-91000 ...

  • Zenoah RMSZ2500 - page 32

    12. Parts list Fig.4 ENGINE UNIT RMSZ2500 (S/N 50100000 and up)  32  ...

  • Zenoah RMSZ2500 - page 33

     33  Key# Description Part Number Q'ty 1 CYLINDER 4810-12111 1 2 GASKET, base 4810-12210 1 3 BOLT 1850-12130 2 4 INSULATOR 4810-13161 1 5 GASKET, insulator 4810-13120 1 6G ASKET, carburetor 4810-13130 1 7 SCREW 0263-90520 1 8 REEDVALVE (S) ASSY 4810-16100 1 9• VALVECASE (S) 4810-16110 1 10 • REEDVALVE 4810-16120 1 11 • STOPPER 4810 ...

  • Zenoah RMSZ2500 - page 34

    EMISSION-RELATED PARTS, FOR TWO (2) YEARS FROM THE DATE OF ORIGINAL DELIVERY OF THE UNIT, KOMATSU ZENOAH AMERICA INC. (THE COMPANY), THROUGH ANY RedMax DEALER, WILL REPAIR OR REPLACE, FREE OF CHARGE, FOR THE ORIGINAL AND EACH SUBSEQUENT PURCHASER, ANY PART OR PARTS FOUND TO BE DEFECTIVE IN MATERIAL AND/OR WORKMANSHIP. EMISSION-RELATED PARTS ARE: TH ...

  • Zenoah RMSZ2500 - page 35

    Pièces en rapport avec les émissions de gaz d'échappement : KOMATSU ZENOAH AMERICA INC., par l'intermédiaire de n'importe quel revendeur RedMax, réparera gratuitement ou remplacera gratuitement pour l'acheteur initial et chaque acheteur successif toute(s) pièce(s) se révélant de constitution et/ou de montage défectueux ...

  • Zenoah RMSZ2500 - page 36

    KOMATSU ZENOAH AMERICA INC. 4344 Shackleford Road Suite 500 Norcross, Georgia 30093 ©P rinted in Japan ...

メーカー Zenoah カテゴリー Lawn Sweeper

Zenoah RMSZ2500のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- RMSZ2500の取扱説明書
- Zenoahの製品カード
- パンフレット
- またはZenoah RMSZ2500の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Zenoah RMSZ2500の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Zenoah RMSZ2500の取り付け説明書、サービスマニュアル、簡易説明書、またはZenoah RMSZ2500のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Zenoah RMSZ2500の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Zenoah RMSZ2500デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがZenoah RMSZ2500を使用するのを助ける技術的文書のことです。説明書は通常、全てのZenoah RMSZ2500ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Zenoahの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Zenoah RMSZ2500の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははZenoah RMSZ2500の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Zenoah RMSZ2500に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Zenoah RMSZ2500デバイスの基本機能を使うにあたってのヒント。 Zenoah RMSZ2500のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Zenoah RMSZ2500に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるZenoah RMSZ2500のメーカー/サービスへの連絡先に関する情報。

Zenoah RMSZ2500についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもZenoah RMSZ2500の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがZenoah RMSZ2500で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)