Planar PE2010の取扱説明書

25ページ 0.26 mb
ダウンロード

ページに移動 of 25

Summary
  • Planar PE2010 - page 1

    PE2010 ...

  • Planar PE2010 - page 2

    1195 NW Compton Drive Beaverton, OR 97006-1992 www.planar.com Customer Service Planar provides the following technical support services: Internet Support For support available 24/7 visit Planar's Online Technical Support at www.planar.com/support. Our Online Technical Support is where you'll find solutions to many common problems, downloa ...

  • Planar PE2010 - page 3

    2 The information contained in this document is subject to change without notice. This document contains proprietary info rmation that is protected by copyright. All rights are reserved. No part of this document may be reproduced, translated to another language or stored in a retrieval system, or transmitted by any means, electronic, mechanical, ph ...

  • Planar PE2010 - page 4

    3 TABLE OF CONTENTS For Your Safety For Your Safety ------------------------------------------------------- 4 General Notes Special notes on LCD monitors ---------------------------------------- 6 Other notes ---------------------------------------------------------- 6 Before You Operate The Monitor Features ---------------------------------------- ...

  • Planar PE2010 - page 5

    4 FOR YOUR SAFETY Before operating the monitor, please read this manual thoroughly. This manual should be retained for future reference. FCC Class B Radio Frequency Interference Statement WARNING: (FOR FCC CERTIFIED MODELS) NOTE: This equipment has been tested and found to comply w ith the limits for a Class B digital device, pursuant to Pa rt 15 o ...

  • Planar PE2010 - page 6

    5 z Do not use the monitor near water, e.g. near a bathtub, washbow l, kitchen sink, laundry tub, sw imming pool or in a wet basement. z Do not place the monitor on an unstable cart, stand, or table. If the monitor falls, it can injure a person and c ause serious damage to the appliance. Use only a cart or stand recommended by the manufacturer or s ...

  • Planar PE2010 - page 7

    6 GENERAL NOTES The following symptoms are normal w ith LCD monitor and do not indicate a problem. • Due to the nature of the fluoresc ent light, the screen may flicker during initial use. Turn off the Power Sw it ch and then turn it on again to make sure the flicker disappears. • You may find slightly uneven br ightness on the screen depending ...

  • Planar PE2010 - page 8

    7 GENERAL NOTES (cont.) • Plug & Play DDC1/2B Feature - This monitor is equipped with VESA DDC1/2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identit y and, depending on the level of DDC used, communicate additional information about its display capabilities. The communication chann ...

  • Planar PE2010 - page 9

    8 BEFORE YOU OPERATE THE MONITOR • 20” (51cm) TFT Color LCD Monitor • Crisp & Clear Display for Window s • Recommended Resolution: 1400 X 1050 @ 60Hz • Ergonomic Design with Tilt Adjustable Stand • Space Saving, Compact Case Design The product package should include the follow i ng items: Monitor Base Landing Strip User Manual Power ...

  • Planar PE2010 - page 10

    9 INSTALLATION INSTRUCTIONS Pow er Source: 1. Make sure that the power cord is the correct type required in your area. 2. This LCD monitor has an internal Universal Power Supply that allows operation in either 100/120V AC or 220/240V AC voltage area (No user adjustment is required.) 3. Connect the AC-power cord into y our LCD monitor’s AC-power-i ...

  • Planar PE2010 - page 11

    10 INSTALLATION INSTRUCTIONS (cont.) Connecting The Cables Figure 2 Connecting Cables 1. AC Power Cord 2. 15-pin D-SUB Cable 3. DVI Cable Turn off your computer befor e performing the procedure below . 1. Connect the female end of the AC pow er cord to the AC-in port on the back of the monitor. Connect the other end to a nearby AC-outlet. 2. Connec ...

  • Planar PE2010 - page 12

    11 INSTALLATION INSTRUCTIONS (cont.) ADJUSTING THE VIEWING ANGLE For optimal viewing it is recommended to l ook at the full face of the monitor, then adjust the monitor's angl e to your ow n preference. Hold the stand so you do not toppl e the monitor w hen you change the monitor's angle. You are able to adjust the monitor's angle fr ...

  • Planar PE2010 - page 13

    12 OPERATING INSTRUCTIONS (cont.) EXTERNAL CONTROLS Figure 4 - External Controls 1. SOURCE 5. Menu / Enter 2. Auto Config / Exit 6. Power Indicator 3. ∧ /ECO changing 7. Power Button 4. ∨ / Bri / con • Pow er Button: Press this button to turn the monitor ON or OFF. • MENU / ENTER: Active OSD menu or function adjust confirm . • ∧ / ECO E ...

  • Planar PE2010 - page 14

    13 OPERATING INSTRUCTIONS (cont.) • Auto Adjust button / Exit: 1. When OSD menu is in active stat us, this button will act as EX IT-KEY (EXIT OSD menu) or go back to the previous menu. 2. When OSD menu is in off status, press this button for 2 seconds to activate the Auto Adjustment function. The Auto Adjustment function is used to set the HPos, ...

  • Planar PE2010 - page 15

    14 OPERATING INSTRUCTIONS (cont.) How To Adjust A Setting 1. Press the MENU-button to activate the OSD window (Figure 5). 2. Press ∧ or ∨ to navigate through the functi ons. Once the desired function is highlighted, press the MENU-button to activate it. If the function selected has a sub-menu, press ∧ or ∨ again to navigate through the sub- ...

  • Planar PE2010 - page 16

    15 OPERATING INSTRUCTIONS (cont.) ADJUSTING THE PICTURE The descriptions for function control LEDS Main Menu Item Main Menu Icon Sub Menu Item Sub Menu Icon Description Reset Value Contrast Contrast from Digital- register. Recall Warm Contrast Value Luminance Brightness Backlight Adjustment Recall Warm Brightness Value Focus Adjust Picture Phase to ...

  • Planar PE2010 - page 17

    16 OPERATING INSTRUCTIONS (cont.) Analog N/A Select input signal from analog source (D-Sub) Input Select Digital N/A Select input signal from digital source (DVI) H. Position Adjust the horizontal position of the OSD. 50 V. Position Adjust the vertical position of the OSD. 50 OSD Setup OSD Timeout Adjust the OSD timeout. 10 English N/A Set OSD disp ...

  • Planar PE2010 - page 18

    17 TECHNICAL SUPPORT (FAQ) (cont.) Problem & Question Possible Solution Power LED is not on *Check if the Power Sw itch is in the ON position *Power Cord should be connected No Plug & Play *Check if the PC system is Plug & Play compatible *Check if the Video Card is Plug & Play compatible *Check if the D-15 plug pin of Video Cable i ...

  • Planar PE2010 - page 19

    18 TECHNICAL SUPPORT (FAQ) (cont.) CLOCK (pixel frequency) controls the number of pixels scanned by one horizontal sweep. If the frequency is not correct, the screen shows vertical stripes and the picture has not correct width. FOCUS adjusts the phase of the pixel clock signal. With a wrong phase adjustment the picture has horizontal disturbances i ...

  • Planar PE2010 - page 20

    19 APPENDIX SPECIFICATIONS Driving system TFT Color LCD Size 51cm(20") Pixel pitch 0.2916mm( H )x 0.2916mm( V ) LCD Panel Viewable angle 160 ° (H) 160 ° (V) R,G,B Analog Interface Video Digital interface H-Frequency 30KHz – 82Hz Input V-Frequency 60 -75Hz Display Colors 16.2M Colors Max. Resolution 1400 x 1050 @ 60Hz Plug & Play VESA D ...

  • Planar PE2010 - page 21

    20 APPENDIX (cont.) Switch • Source • Auto Config / Exit • ∧ / ECO • ∨ / Bri/Con • Menu / Enter • Power Button External Controls: Functions • Contrast • Brightness • Focus • Clock • H.Position • V.Position • Warm Color • Cool Color • SRGB Color temperature • User • Input signal Selection • OSD position, OSD t ...

  • Planar PE2010 - page 22

    21 APPENDIX (cont.) Preset Display Modes STANDARD RESOLUTION HORIZONTAL FREQUENCY(KHZ) VERTICAL FREQUENCY(HZ) IBM DOS 720 × 400 31.47 70.0 640 × 480 31.47 60.0 VGA 640 × 480 37.50 75.0 800 × 600 37.879 60.0 SVGA 800 × 600 46.875 75.0 1024 × 768 48.363 60.0 1024 × 768 56.476 70.0 1024 x 768 60.02 75.0 1024 x 768 48.780 60.0 VESA XGA 1024 x 76 ...

  • Planar PE2010 - page 23

    22 APPENDIX (cont.) Connector Pin Assignment 15 6 10 11 15 15 - Pin Color Display Signal Cable PIN NO. DESCRIPTION PI N NO. DESCRIPTION 1. Video-Red 9. +5V 2. Video-Green 10. Detect Cable 3. Video-Blue 11. NC 4. NC 12. DDC-Serial data 5. Ground 13. H-sync 6. GND-R 14. V-sync 7. GND-G 15. DDC-Serial clock 8. GND-B ...

  • Planar PE2010 - page 24

    23 APPENDIX (cont.) 24 - Pin Color Display Signal Cable PIN NO. DESCRIPTION PI N NO. DESCRIPTION 1. TMDS Data 2- 13. T MDS Data 3+ 2. TMDS Data 2+ 14. +5V Power 3. TMDS Data 2/4 Shield 15. Ground(for+5V) 4. TMDS Data 4- 16. Hot Plug Detect 5. TMDS Data 4+ 17. TMDS Data 0- 6. DDC Clock 18. T MDS Data 0+ 7. DDC Data 19. TMDS Data 0/5 Shield 8. NC 20. ...

  • Planar PE2010 - page 25

    Q41G2002935 1B 1195 NW Compton Drive Beaverton, OR 97006-1992 www.planar.com © 2006 Planar Systems, Inc. Planar is a registered trademark of Planar Systems, Inc. Other brands and names are the property of their respective owners. Technical information in this document is subject to change without notice. ...

メーカー Planar カテゴリー Car Video System

Planar PE2010のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- PE2010の取扱説明書
- Planarの製品カード
- パンフレット
- またはPlanar PE2010の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Planar PE2010の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Planar PE2010の取り付け説明書、サービスマニュアル、簡易説明書、またはPlanar PE2010のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Planar PE2010の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Planar PE2010デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがPlanar PE2010を使用するのを助ける技術的文書のことです。説明書は通常、全てのPlanar PE2010ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Planarの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Planar PE2010の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははPlanar PE2010の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Planar PE2010に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Planar PE2010デバイスの基本機能を使うにあたってのヒント。 Planar PE2010のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Planar PE2010に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるPlanar PE2010のメーカー/サービスへの連絡先に関する情報。

Planar PE2010についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもPlanar PE2010の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがPlanar PE2010で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)