-
CDA EVPK9 - page 1
Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshir e • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www .cda.eu Passionate about style E VPK9 Linear Extr act or Manual for Inst allation, Use and Maintenanc e ...
-
CDA EVPK9 - page 2
Important The manufacturer cannot be held r esponsible for injuries or losses caused by inc orrect use or installation of this pr oduct. Please note that the manufactur er reserves the right t o invalidate the guar antee supplied with this product f ollowing incorr ect installation or misuse of the appliance or use in a commer cial envir onment. Th ...
-
CDA EVPK9 - page 3
2 Using your Extr actor For best perf ormance, you should switc h on the extractor 1 5 minutes befor e starting to cook and lea ve it to run for appro ximately 1 5 minutes after the end of cooking. Contr ol Panel A - Light key B - Decrease speed k ey C - Display D - Increase speed k ey E - Timer key T o switc h the extr actor light on and off • T ...
-
CDA EVPK9 - page 4
3 Car e and Maintenanc e IMPOR T ANT : DO NO T PERFORM MAINTENANCE OR CLEANING OF THE EXTRACT OR WITHOUT FIRST SWIT CHING OFF THE ELECTRICITY SUPPL Y . Cleaning Y ou should use a nonabrasive cleaner . Any abrasive cleaner (including Cif) will scratc h the surface and could er ase the control panel markings. Y ou can clean your extract or effectivel ...
-
CDA EVPK9 - page 5
4 Changing the Light DO NO T CHANGE THE LIGHT BULB IMMEDIA TEL Y AFTER USE AS THE BULB WILL BE HO T . ALL O W IT T O COOL BEFORE REM OVING IT . Using a flat blade screwdriv er , carefully prise off the lamp cover as shown in figur e 5. Remove the bulb and r eplace with a 1 2V 20W halogen light bulb. Finally , replace the light bulb cover . Do not ...
-
CDA EVPK9 - page 6
5 DOUBLE POLE SWIT CHED FUSED SPUR OUTLET USE A 3 AMP FUSE Mains Electricity Connection THIS APPLIANCE MUST BE C ONNECTED T O THE MAINS SUPPL Y BY A C OMPETENT PERSON, USING FIXED WIRING VIA A DOUBLE POLE SWIT CHED FUSED SPUR OUTLET AND PR O TECTED B Y A 3A FUSE. W e recommend that the appliance is connect ed by a qualified electrician, who is a m ...
-
CDA EVPK9 - page 7
Electrical Information Mains electrical voltage: 230 – 240Vac, 50Hz T otal r ated pow er consumption: 290W T r oubleshooting If your extr actor is not w orking: 1 . Check that the mains supply has not been swit ched off. 2. Check that the fuse in the spur has not blown. 6 ...
-
CDA EVPK9 - page 8
7 Mounting your Extr act or IMPOR T ANT : The extr actor is intended t o be mounted dir ectly to the ceiling using fixings appr opriate for the c eiling. Ensure that ther e is adequate c eiling strength and supports at the fixing points; if in doubt, consult a joiner or electrician. When the extractor is t o be installed above an electric hob, th ...
-
CDA EVPK9 - page 9
8 Installation Y our extractor can be used t o filter and recy cle the air within your kitc hen (A), or to extract the air outside (B). When extracting air to the outside, the unit can be v ented as shown in the diagram below . T o mount your extr actor t o the ceiling 1 . Fir stly , remove the low er section of the support frame, by removing the ...
-
CDA EVPK9 - page 10
9 Installation 4. Insert 3 screws into the main fixings, lea ving appro ximately 3mm protruding, as shown in Fig 7 5. Fit the upper support section (B) into position on the 3 screw s and rotat e it into position, as shown in Fig 7 . 6. When in position, tighten the 3 main screws and fit an additional screw (X) t o fix the support frame section i ...
-
CDA EVPK9 - page 11
10 Installation 9. Assemble the ventilation duct(H), as shown in the diagrams below dependant on whether you ar e extracting air to the outside (Fig 1 0) or re-cir culating (Fig 1 1), in which case you will need to use the supplied T -piece (M). Ensur e that the duct adapter (F) is securely connected to the duct pipe or T -piece in order t o minimi ...
-
CDA EVPK9 - page 12
11 Installation 1 1 . Mount the upper c himney section onto the frame section and secure in position using the 2 scr ews (A) as in Fig 1 3. 1 2. Carefully slide the low er section over the upper section and tape it in position (L) near the shortest position. 1 3. Fit 2 screw s into the holes on the body of the hood (O), leaving appr oximately 3mm p ...
-
CDA EVPK9 - page 13
12 ...
-
CDA EVPK9 - page 14
13 ...
-
CDA EVPK9 - page 15
14 ...
-
CDA EVPK9 - page 16
Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshir e • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www .cda.eu Passionate about style T o contact our Customer Car e Department, or for Service, please contact us on the det ails below . ...
CDA EVPK9についてご質問がありますか?
次のフォームを使用してください
見つけた説明書を読んでもCDA EVPK9の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがCDA EVPK9で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。