ページに移動 of 90
IEEE 1394 OHCI CardBus PC Card for W indows 98SE/2000/Me & for Mac OS 9.0.4 or later CBFW3 User ’ s Guide Rev . 1.0 April 2001 ...
CBFW3 User's Guide 1. Introduction ........................................................................... 1 1-1. Before Using the CBFW3 1 1-2. Package 1 1-3. Features 2 1-4. System Requirements 2 1-5.Restrictions 3 1-6.Compatibility with V ideo Editing software. 4 2. Setup for Windows ...................................................... ...
4. How to use RsDvCap .......................................................... 31 4-1.Main menu 3 2 4-2.Control Bars 33 4-2-1.Camera and Audio Select Bar 33 4-2-2.Camera Control Bar 33 4-2-3.V ideo Control Bar 34 4-3.Application settings 3 5 4-4.Capturing a video from a DVCAM in camera mode 39 4-5.Capturing a video from a DV tape 40 4-6.DV Batch ...
9. Registration and T ech-Support .......................................... 83 9-1. How to Register 83 9-2. Software Update and Support 83 10. Options ............................................................................... 84 1 1. Specifications ..................................................................... 85 Appendix ............. ...
1 1. Intr oduction This User ’ s Guide describes how to install, use, and troubleshoot the RA TOC CBFW3 IEEE1394(FireW ire) CardBus PC Card for W indows and Macintosh users. If you purchased W indows package, refer to the W indows chapter . If you purchased Macintosh package, refer to the Macintosh chapter . The information in the README file on ...
2 1-3. Features • T wo external IEEE1394 ports are available at card. • IEEE-1394.a compatible PHY chip is on card. • Full backward compatibility to IEEE1394-1955 device. • OHCI 1.0 fully compliant Link chip is on card. • 100, 200 and 400Mbps data rate is automatically supported at each IEEE1394 port. • Class 1(15W) cable power is avail ...
3 1-5.Restrictions For W indows Users •If the following CardBus Bridge chip name is the same as your laptop uses, you can not use the CBFW3 with your laptop. -Ricoh RL5C465 CardBus Controller -Ricoh RL5C466 CardBus Controller -Cirrus Logic PD6832 CardBus Controller If your CardBus Bridge name is Ricoh CardBus Bridge RL5C476, the following problem ...
4 For W indows Users Microsoft Standard WDM DV filter drivers captures DV data stream and save as an A VI file which consists with original DV data stream. This DV data stream requires 3.6MB/ sec and includes 720x480 resolution video data(NTSC). Also, the file size is restricted up to 4GB (about 19 minutes). As our application named RsDvCap uses th ...
5 *1 For Macintosh users Y ou can use the following video editing software with the CBFW3. (As of March in 2001) For more information, contact the manufacturer of the software. Data Import from a DV device V ideo Editing Controlling a DV device Exporting to a DV device Manufacturer Software Adobe Premiere 5.1c O.K. O.K. O.K. O.K. Apple Final Cut Pr ...
6 If you are a W indows user, go to the Chapter 2 to set up the CBFW3. If you are a Macintosh user , go to the Chapter 7 to set up the CBFW3. ...
7 2. Setup for W indows T o use the CBFW3 on W indows, follow the steps. 1.Insert the CBFW3 into the PC Card slot. Refer to the Chapter 2-1. 2.Install the OHCI driver . Refer to the Chapter 2-2. 3.Connect an IEEE1394 device to the CBFW3. If you connect a DVCAM, refer to the Chapter 2-3. If you connect a CCD camera, refer to the Chapter 2-4. If you ...
Windows 98SE 8 2-2-1.Windows 98 SE Installation T o use the CBFW3 on W indows 98 SE, follow the steps. Step1.Install the OHCI driver 1.When the CBFW3 is inserted into the PC Card slot, Hardware W izard will detect the CBFW3 automatically and you will see the screen below . Click [Next] . Then, you need to install the OHCI driver installation. When ...
Windows 98SE 9 5.When the following window appears, click [Next] . 4.When the following window appears, select [The updated driver (Recommended) T exas Instruments OHCI Compliant IEEE 1394 Host Controller] . Then click [Next] . 3.When the following window appears, click [Next] . (Y ou do not need to check any boxes) ...
Windows 98SE 10 6.When the following window appears, insert the W indows 98 Second Edition CD-ROM into the CD-ROM drive. Then click [OK] . 7.If the following window appears, type “D: Win98” or “C:Windowsoptionscabs” in the Copy files from box, where “D” means the CD-ROM drive. After that, click [OK] . If your CD-ROM drive is not ? ...
Windows 98SE 11 Step3.Installing MSDV .SYS update program Install MSDV update program( 252640USA8.EXE ) when you use Windows 98 SE. Follow the steps to install MSDV update program. 1.Set the CBFW3 CD-ROM into your CD-ROM drive. 2.Open [My Computer] and double-click CD-ROM drive icon. 3.Double-click [Win98SE] folder and double-click the [DvPatch] fo ...
Windows 98SE 12 Step4.Microsoft Windows Update Y ou should update your W indows 98 SE to improve performance. T o update your W indows 98 SE, follow the steps. 1.Click Start with the left button of the mouse. 2.Select Windows Update . 3.Y ou will see the screen below . Click PRODUCT UPDA TES . 4.Y ou will see the screen below .Check Storage Supplem ...
Windows 2000 13 2-2-2.Windows 2000 Installation T o use the CBFW3 on W indows 2000, follow the steps. V erify the OHCI driver installation When you insert the CBFW3 into the PC Card slot, the OHCI driver is installed automatically by the Hardware W izard. T o verify the OHCI driver Installation, follow the steps. 1.Click My Computer with the right ...
Windows 2000 14 5.If there is a T exas Instruments OHCI Compliant IEEE 1394 Host Controller string without any yellow “!” marks or red “X” marks under the IEEE 1394 Bus host controllers , the OHCI driver for the CBFW3 is installed correctly . Check here ...
Windows Me 15 2-2-3.Windows Me Installation T o use the CBFW3 on W indows Me, follow the steps. Step1.Install the OHCI driver 1.When the CBFW3 is inserted into the PC Card slot, Hardware W izard will detect the CBFW3 automatically and you will see the screen below . Select [Automatic search for a better driver(Recommended)] and click [Next] . 2.Whe ...
Windows Me 16 Step2.V erify the OHCI driver installation T o verify the OHCI driver installation,follow the steps. 1.Click My Computer with the right button of the mouse. 2.Select Properties . 3.Y ou will see the screen below . Click the Device Manager tab. 4.Double-click “1394 Bus Controller” . 5.If there is a T exas Instruments OHCI Compliant ...
17 2-3.DVCAM Installation This section describes how to connect a DVCAM and install the DV driver . Connect the CBFW3 and a DVCAM using the IEEE1394 cable as shown below . And turn on the DVCAM power switch. Y ou can connect the DVCAM without turning off the PC or DVCAM. 4pin-6pin IEEE1394 cable which comes with this package When your W indows vers ...
Windows 98SE Windows Me 18 2-3-1.Windows 98 SE/Windows Me DV Driver Setup V erify the DV driver installation When you connect a DVCAM on W indows 98 SE or Windows Me, the DV driver will be installed automatically . T o verify the DV driver installation, follow the steps. 1.Click My Computer with the right button of the mouse. 2.Select Properties . ...
Windows 2000 19 2-3-2.Windows 2000 DV Driver Setup V erify the DV driver installation When you connect a DVCAM on W indows 2000, the DV driver will be installed automatically . T o verify the DV driver installation, follow the steps. 1.Click My Computer with the right button of the mouse. 2.Select Properties . 3.Y ou will see the screen below . Cli ...
Windows 2000 20 5.If there is a “Microsoft DV Camera and VCR” string without any yellow “!” marks or red “X” marks under the [Imaging devices] as shown below , the DV driver is installed correctly . Check here ...
21 2-4.Desktop CCD Camera Installation This section describes how to connect a CCD camera and install the driver . Follow the steps to connect a CCD camera. 1.Connect the optional AC adapter(sold separately) to the CBFW3. 2.Connect a CCD camera to the CBFW3 with an IEEE1394 6pin-6pin cable. 3.Y ou can connect the CCD camera without turning off the ...
Windows 98SE Windows Me 22 2-4-1.Windows 98SE/Windows Me CCD Camera Setup When the CCD camera is connected,the CCD camera will be recognized automatically . T o verify the CCD driver installation, follow the steps. 1.Click My Computer with the right button of the mouse. 2.Select Properties . 3.Click the Device Manager tab. 4.Double-click “Imaging ...
Windows 2000 23 When the CCD camera is connected, the CCD camera will be recognized automatically . T o verify the CCD driver installation, follow steps through. 1.Click My Computer with the right button of the mouse. 2.Select Properties . 3.Y ou will see the screen below . Click the Hardwar e tab. 4.Click the Device Manager button. 2-4-2.Windows 2 ...
Windows 2000 24 5.If there is a CCD camera name string without any yellow “!” marks or red “X” marks under the [Imaging devices] as shown below , the driver is installed correctly . Check here ...
25 2-5.1394 Storage Installation This section describes how to connect a 1394 storage and install the driver . 1394 storage means Hard Disk Drives(HDDs), Magneto Optical Disks(MOs), etc. Only W indows 98 SE, Windows 2000 or W indows Me support such 1394 storage. The cable powered HDD, MO doesn’t work without a power source. Y ou can use our AC po ...
Windows 98SE Windows Me 26 When the 1394 HDD is connected, W indow will install the driver automatically . T o verify the 1394 storage driver installation, follow the steps. 1.Click My Computer with the right button of the mouse. 2.Select Properties . 3.Y ou will see the screen below . Click the Device Manager tab. 4.Doble-click “Storage device? ...
Windows 2000 27 When the 1394 HDD is connected, W indow 2000 will install the driver automatically . T o verify the 1394 storage driver installation,follow the steps. 1.Click My Computer with the right button of the mouse. 2.Select Properties . 3.Y ou will see the screen below . Click the Hardwar e tab. 4.Click the Device Manager button. 2-5-2.Wind ...
Windows 2000 28 5.If there is a 1394 HDD name string without any yellow “!” marks or red “X” marks under the [Disk drives] as shown below , the 1394 storage driver is installed correctly . Check here ...
29 3. Setup RsDvCap Installing RsDvCap/RsDvStill/CompressA VI 1.Close all programs currently running on your computer . 2.Set the CBFW3 CD-ROM in your CD-ROM drive. 3.Open [My Computer] and double-click CD-ROM drive icon. 4.Open [W in98SE] , [W in2000] or [W inMe] folder . If your W indows version is W indows 98 SE(Second Edition), open [Win98SE] f ...
30 10.Y ou will see the screen below . Select [Y es, I want to restart my computer now] and click [Finish] . Y ou have now completed installing the capture software. NOTE If you have installed this softwar e already and start this installer , this installer will delete the software and end. Y ou have to start the installer again to install this sof ...
31 4. How to use RsDvCap What is the RsDvCap? This application software has the following functions. •Preview and capture video/sound data from a DVCAM. •Preview and capture video data from a CCD camera. •Export media file from a PC to a DVCAM. •Playback media file. Main menu Camera Control Bar Camera and Audio Select Bar Batch Capture List ...
32 4-1.Main menu: T op menu Sub menu Description File Review movie file END T erminate this application. Setting DV Batch Capture Show batch capture dialog box.Refer to 4-6.DV Batch Capture . Application Setting Show RsDvCap parameter setting dialog box. Refer to 4-3.Application settings . Cam Setting Show CCD camera control dialog box. V iew Camer ...
33 4-2.Control Bars 4-2-1.Camera and Audio Select Bar: This bar has the Camera list box and Sound device list box as shown above. Camera list box displays a list of camera device connected to your PC. If this list box is blank, your camera isn’t recognized. “Microsoft DV Camera and VCR” string will appear if your camera is recognized. Sound d ...
34 4-2-3.V ideo Control Bar : Y ou can control a DVCAM from this control bar . The DVCAM have a switch which selects video mode or camera mode. If you set this switch to camera mode or a DV tape is not inserted, this control bar will be disabled automatically . Set this switch to video mode to control the DVCAM. The functions are below: ...Rewind . ...
35 4-3.Application settings When you select [Application setting] of the [Setting] menu, you will see the dialog box below . Y ou can set up this application’ s behavior . ...
36 Category Item Description Camera Mode CCD Mode Select when you use a CCD camera. DV Mode Select when you use a DVCAM. Preview Settings Display TimeCode If checked, timecode will be displayed. DV Codec Resolution Capture Settings Capture With Preview Rename file name every capture execution Y ou can select DV Codec Resolution. If you select a hig ...
37 Category Item Description DVCAM Settings Check DVCAM Mode If you click here, this application will detect whether your DVCAM is in camera mode or video mode automatically . If your DVCAM is in video mode, the Camera Control Bar will disappear . If your DVCAM is in camera mode, the Camera Control Bar will appear and the V ideo Control Bar will be ...
38 C Category Item Description When you control a DVCAM from the PC consecutively , it takes some time for the DVCAM to get ready for a next command from the PC. This time depends on the DVCAM. If you have trouble in controlling the DVCAM from the PC consecutively , change this value to a longer time than 4 seconds. Default time is 4 seconds. For e ...
39 4-4.Capturing a video from a DVCAM in camera mode When you want to capture a video image from a DVCAM set to camera mode, follow steps through. 1. Confirm a DVCAM is set to camera mode. Camera mode means you can capture a video image. If your DVCAM is in video mode, change mode selection switch from video mode to camera mode slowly . Everytime y ...
40 4-5.Capturing a video from a DV tape 1. Set a DV tape in a DVCAM and confirm the DVCAM mode is set to video mode. V ideo Mode means you can control a video of a DV tape. If your DVCAM is in camera mode, change mode selection switch from camera mode to video mode slowly as mentioned 4-4.Capturing a video from a DVCAM in camera mode . 2.Select [DV ...
41 4-6.DV Batch Capture Batch capture function saves video images files as your time scheduling. T o batch capture video images from a DV tape, follow steps through. 1.T o show the Batch Capture W indow as shown right, select [Batch Capture List] of the [V iew] in the system menu. 2.Set a DV tape in a DVCAM and confirm the DVCAM mode is set to vide ...
42 9. The Batch Capture dialog box will be shown. Click [RUN] to start batch capture.This application searchs automatically the timecode you have just set and starts to capture video images and saves the file in the folder written in the “Export Directory” under the name of V ideo + (number) starting 1 + .avi as shown below . When batch capture ...
43 4-7.Exporting a video data to a DVCAM When you want to export an video data to a DVCAM, follow steps through. 1. Set a DVCAM to video mode. V ideo Mode means you can control a video of a DV tape. If your DVCAM is in camera mode, change mode selection switch from camera mode to video mode slowly as mentioned 4-4.Capturing a video from a DVCAM in ...
44 5. How to use RsDvStill What is the RsDvStill? This application software has the following functions. •Preview video data from a DVCAM/a CCD camera. •Save a still image to a BMP file. When RsDvStill starts with a DVCAM connected to the CBFW3, RsDvStill will detect whether the DVCAM is in camera mode or in video mode automatically and pauses ...
45 Category Description DV Maker This list box shows a list of DVCAM manufacturer such as Sony , JVC, Panasonic, Canon, Sharp, etc. Choose your DVCAM manufacturer . If you can’t find it, choose OTHER. Image Size There are 3 kinds of resolution:720 x 480, 360 x 240, 88 x 60. This value means raw data from a DVCAM. Slider Bar Y ou can select a favo ...
46 Category Description T ime Code This box shows the timecode information of your DV tape. This timecode format is HOUR:MINUTE:SECOND:FRAME. When you click this button, you will see the screen below . Y ou can select a folder where you want to save a BMP file. This button will be enabled only when you click the button. When you click the button, p ...
47 5-2.How to save a BMP file (1)Save a BMP file from a DV tape 1.Set a DV tape in a DVCAM and confirm the DVCAM mode is set to video mode. V ideo Mode means you can control a video of a DV tape. If the DVCAM is in camera mode, change mode selection switch from camera mode to video mode slowly as mentioned 4-4. Capturing a video from a DVCAM in cam ...
48 (2)Save a BMP file from a DVCAM in camera mode or a CCD camera 1.Set a DVCAM to camera mode. Camera mode means you can capture a video image. If your DVCAM is in video mode, change mode selection switch from video mode to camera mode slowly as mentioned 4-4.Capturing a video from a DVCAM in camera mode. When you use a CCD camera, skip this step. ...
49 6. How to use Compr essA VI What is CompressA VI application software? This application software has the following functions. Convert Microsoft DV-A VI2 format video file to another format video file bi-directionally . As current existent video editing software don't support MS DV-A VI2 format video file, you have to convert the format of v ...
50 3.Please specify an original video file and a converted video file name. Click [Next] . (After conversion, an original video file remains in the HDD.) 6-1.How to convert the MS DV-A VI2 format to other formats 1.When you start the CompressA VI, you will see the screen below . Click [Execute] . 2.Please select “Convert DV-A VI fomat to other vi ...
51 4.Please choose a conversion filter from the Compression formats list box. A VI files made by RsDvCap have a MS DV-A VI2 format. So, select the other compression formats than DV V ideo Encorder . There are many kinds of compression formats. (Compression formats appeared in the [Compression formats] list box depend on your system) Popular compres ...
52 5.Click [Next] . The file conversion starts. It takes much time to convert an A VI file. Conversion time depends on the type of compression format. Please wait patiently . 6.When conversion ends, you will see the screen below . Click [Finish] . Y ou can now do a video editing with your video editting software. ...
53 6-2.How to convert other formats to the MS DV-A VI2 format? Y ou can export a video to a DVCAM after you convert an existing A VI file to the MS DV-A VI2 format. 1.When you start the CompressA VI, you will see the screen below . Click [Execute] . 2. Please select “Convert other video file format to DV-A VI file format” and and choose NTSC or ...
54 5.When conversion ends, you will see the screen below . Click [Finish] . Y ou can now export the converted data to a DVCAM by using RsDvCap. 4.Click [Next] . It may take much time to convert an A VI file. Please wait patiently . ...
Macintosh 55 7. Setup for Macintosh T o use the CBFW3 on Macintosh, follow the steps below . 1.Install the CBFW3 driver . Refer to the Chapter 7-1. 2.Insert the CBFW3. Refer to the Chapter 7-2. 3.Connect a FireW ire device to the CBFW3. Refer to the Chapter 7-3. ...
Macintosh 56 7-1.CBFW3 driver installation Before you insert the CBFW3 into the PC Card slot, you have to install the CBFW3 driver . T o install the CBFW3 driver , follow the steps. 1.Close all programs currently running on your computer . 2.Insert the CBFW3 CD-ROM into the CD-ROM drive. 3.The following icon will mount on the desktop.Double click t ...
Macintosh 57 6.The following window will show up. Click [Install] . 7.The following window will show up. Click [Restart] to restart your Mac. 8.Open [Extensions] folder in the [System Folder] . If you can find the REX-CBFW Enabler , the CBFW3 driver was installed correctly . ...
Macintosh 58 7-2.Inserting the CBFW3 1.Insert the CBFW3 into the PC Card slot as shown below . Refer to the manual that accompanied with your Mac for the location of the PC Card slot. NOTE Y ou may not be able to insert another PC Card with the CBFW3 simultaneously . Y ou may not be able to insert the CBFW3 in the upper PC card slot. T o remove the ...
Macintosh 59 7-3.Connecting a FireWire device to the CBFW3 Follow the steps to connect a 1394 Hard Disk Drive(HDD). 1.Insert the CBFW3 into the PC Card slot. 2.Connect the optional AC adapter(sold separately) to the CBFW3 only when you connect a FireW ire device which needs cable power such as a HDD, MO. 3.Connect a FireW ire device to the CBFW3 wi ...
60 2. If you use W indows 98 SE or W indows 2000,there have to be a [Microsoft DV Camera and VCR] string under the “Imaging Device” in the Device Manager . If you can not find it, make sure your DVCAM is powered on. If you use W indows Me, there have to be a camera name string under the “Imaging Device” in the Device Manager . If you can no ...
61 8-2.When you can not export smooth and clear video image to a DVCAM(Windows 98SE/Me) If you use W indows 2000, see 8-3.When you can not export smooth and clear video image to a DVCAM(Windows 2000) . In the CBFW3 CD-ROM , there is the driver for CardBus Bridge property setting controller named CBRPSET .VXD (for W indows 98 SE) or MERPSET .VXD (fo ...
62 CardBus Bridges name list CardBus Bridge chip made by RICOH: -Ricoh RL5C476 CardBus Controller -Ricoh RL/RB5C478 CardBus Controller -Ricoh RL5C475 CardBus Controller CardBus Bridge chip made by TEXAS INSTRUMENTS(TI): -T exas Instruments PCI-1210 CardBus Controller -T exas Instruments PCI-121 1 CardBus Controller -T exas Instruments PCI-1220 Card ...
63 2. Restrictions. If you come across the following CardBus Bridge chip, unfortunately you can not use the CBFW3. -Ricoh RL5C465 CardBus Controller -Ricoh RL5C466 CardBus Controller -Cirrus Logic PD6832 CardBus Controller If you come across Ricoh CardBus Bridge RL5C476, please note the following restrictions. The driver will improve DV export capa ...
64 3.How to install the driver:CBPRSET .SYS or MERPSET .SYS Y ou have already installed the driver [T exas Instruments OHCI Compliant IEEE 1394 Host Controller] . Y ou should replace it to the new “RA TOC 1394 CardBus Card(TI OS V ersion)” driver . Y ou can replace it, simply following the instructins: 1.Insert the CBFW3 PC Card into the PC Car ...
65 Y ou will see the screen below when you use Windows Me . Select [Specify the location of the driver(Advanced)] and click [Next] . 7.Click the Driver tab and click [Update Driver ...] . 8.Y ou will see the screen below if you use Windows 98SE . Click [Next] . ...
66 9.Y ou will see the screen below when you use Windows 98 SE . Select [Display a list of all drivers in a specific location,so you can select the driver you want] and click [Next] . Y ou will see the screen below when you use Windows Me . Select [Display a list of all drivers in a specific location,so you can select the driver you want] and click ...
67 13.Y ou will see the screen below . Click [Next] . 1 1.Y ou will see the screen below . Set the CBFW3 CD-ROM in the CD-ROM drive and type “DWin98SE” or “DWinMe” , where “D” means the CD-ROM drive. When you use W indows 98 SE, type “DW in98SE” . When you use WindowsME, type “DWinMe” . After that, click [OK] . 12.Y ou will ...
68 15.When a dialog box says [The file cbrpset.vxd on RA TOC FW Install CD can not be found. Insert RA T OC FW Install CD in the selected drive,and click OK.] , type “D:Win98SE” and click [OK] . This message may appears only when your W indows is Windows 98SE . 14.If the following message appears,make sure that the CBFW3 CD-ROM is inserted in ...
69 18.Make sure you can find a [RA T OC 1394 CardBus Card(TI OS V ersion)] string in the Device Manager . If there is yellow “!” mark on a [RA TOC 1394 CardBus Card(TI OS V ersion)] string, restart your laptop PC again. 16.Y ou will see the screen below . Click [Finish] . 17.Y ou will see the screen below . Click [Y es] . Y ou have now complete ...
70 8-3.When you can not export smooth and clear video image to a DVCAM(Windows 2000) If you use W indows 98 SE/W indows Me, see 8-2.When you can not export smooth and clear video image to a DVCAM(Windows 98SE/Me) .In the CBFW3 CD-ROM , there is the driver for CardBus Bridge property setting controller named CBPRSET .SYS . This CBPRSET .SYS driver i ...
71 CardBus Bridges name list CardBus Bridge chip made by RICOH: -Ricoh RL5C476 CardBus Controller -Ricoh RL/RB5C478 CardBus Controller -Ricoh RL5C475 CardBus Controller CardBus Bridge chip made by TEXAS INSTRUMENTS(TI): -T exas Instruments PCI-1210 CardBus Controller -T exas Instruments PCI-121 1 CardBus Controller -T exas Instruments PCI-1220 Card ...
72 2. Restrictions. If you come across the following CardBus Bridge chip, unfortunately you can not use the CBFW3. -Ricoh RL5C465 CardBus Controller -Ricoh RL5C466 CardBus Controller -Cirrus Logic PD6832 CardBus Controller If you come across Ricoh CardBus Bridge RL5C476, please note the following restrictions. The driver will improve DV export capa ...
73 3.How to install the driver:CBPRSET .SYS Y ou have already installed the driver [T exas Instruments OHCI Compliant IEEE 1394 Host Controller] . Y ou should replace it to the new “RA T OC 1394 CardBus Card(TI OS V ersion)” driver . Y ou can update and replace it, simply following the instructions below . 1.Insert the CBFW3 PC Card into the PC ...
74 7.Y ou will see the screen below . Click the Driver tab and click [Update Driver ...] . 8.Y ou will see the screen below . Click [Next] . ...
75 1 1.Y ou will see the screen below . Insert the CBFW3 CD-ROM and type “D:W in2000” , where D means your CD-ROM drive and click [OK] . 9.Y ou will see the screen below . Check [Sear ch for a suitable driver for my device (recommended)] and click [Next] . 10.Y ou will see the screen below . Check [Specify a location] and click [Next] . ...
76 12.Y ou will see the screen below . Click [Next] . 13.Y ou will see the screen below . Click [Finish] . ...
77 Y ou have now completed the installation of the driver . Please try DV Export function with RsDvCap.exe. 16.Make sure there is a [RA TOC 1394 CardBus Card (TI W in2K version)] string in the Device Manager . I If there is yellow “!” mark on [RA T OC 1394 CardBus Card (TI Win2K version)] , restart your PC again. 15.Y ou will see the following ...
78 8-4. A captured file is choppy or jerky I The data rate from a DVCAM is 3.6MB/sec. If your HDD sustainted data write rate is lower than 3.6MB/sec., a captured file may get choppy or jerky when you play back the file. T o avoid this trouble, enable DMA function of your HDD, following the steps. 1.Open “Device Manager” . 2.Select your Disk dri ...
79 8-5.Using the format utility named FRFMTW9X.EXE Y ou can format a 1394 storage device such as a HDD, Zip, MO with format utility named FRFMTW9X.EXE. This utility is included in the CBFW3 CD-ROM. This FRFMTW9X.EXE runs only on W indows 98SE, W indows Me. If you want to format a 1394 storage device on W indows 2000, refer to 8-6.Formatting media o ...
80 6.Y ou will see the screen below . Select [Initialize/Format media] from the [Edit] menu. 7.Y ou will see the Initialize/Format screen below . Select format type . If you want to do Low Level Format simultaneously , check [Low Level Format] . Then, click [OK] . (Caution) Y ou can do low level format only for a HDD, MO which is converted from SCS ...
81 8.If you selected IBM-PC/A T FDISK format at step 7), the message box saying [Y ou should cr eate partition next] appears. Then, click [OK] . Y ou will see the screen shown in the step 6) and select [Create Partition] from the [Edit] menu. After that, you will see the screen below . Select [File System] from the list box and set Partition size, ...
82 8-6.Formatting media on Windows 2000 When you want to format a 1394 storage device such as a HDD, Zip, MO on W indows 2000, you can use [Computer Management] . Here is a brief explanation: 1.Open [My Computer] and double click [Control Panel] . 2.Double click [Administrative T ools] and start [Computer Management] . 3.The following window will s ...
83 9. Registration and T ech-Support 9-1. How to Register W e highly recommend to register yourself as our customer through our on-line registration. 1 . On the Internet, access our site ( http://www .ratocsystems.com/english/ ) 2 . Follow window menu guide to register . 3 . Fill out and submit the registration form. 9-2. Software Update and Suppor ...
84 10. Options Options are available (sold separately) at the web site: 1. http://www .ratocsystems.com/english/ 2. http://www .firewir eshop.com -CBFW-466 (4pin-6pin IEEE1394(FireWire) cable(6 feet)) -CBFW-666 (6pin-6pin IEEE1394(FireWire) cable(6 feet)) -CBFW-463 (4pin-6pin IEEE1394(FireWire) cable(3 feet)) -CBFW-663 (6pin-6pin IEEE1394(FireWire) ...
85 1 1. Specifications Product Name :CBFW3 IEEE1394 CardBus PC Card Transfer :PC Card Standard(CardBus) 32bit Bus Master Data Transfer Rate :100/200/400Mbps Power Requirements : V oltage :+3.3V(Supplied from PC Card Slot) Current :110mA (Idle) 220mA (MAX) Operating Environment : T emperature : 0°C(32°F)-55°C(131°F) Relative humidity: 95% Max.(N ...
86 Appendix T rademarks -Windows is a registered trademark of Microsoft Corporation. -Sony Corporation has a original copyright of SONYDVCR.SYS. - Other brand and product names may be registered trademarks or trademarks of their respective holders. I)FCC Statement This equipment has been tested and found to comply with the limits for a Class B digi ...
Ratoc Systems CBFW3のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- CBFW3の取扱説明書
- Ratoc Systemsの製品カード
- パンフレット
- またはRatoc Systems CBFW3の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Ratoc Systems CBFW3の取扱説明書に含まれています。
取扱説明書と呼ばれる文書のグループは、Ratoc Systems CBFW3の取り付け説明書、サービスマニュアル、簡易説明書、またはRatoc Systems CBFW3のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Ratoc Systems CBFW3の製品を使用するにあたって最も人気のある説明書を閲覧できます。
Ratoc Systems CBFW3デバイスの取扱説明書はどのようなものですか？
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがRatoc Systems CBFW3を使用するのを助ける技術的文書のことです。説明書は通常、全てのRatoc Systems CBFW3ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。
Ratoc Systemsの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。
1. Ratoc Systems CBFW3の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははRatoc Systems CBFW3の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Ratoc Systems CBFW3に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Ratoc Systems CBFW3デバイスの基本機能を使うにあたってのヒント。 Ratoc Systems CBFW3のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Ratoc Systems CBFW3に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるRatoc Systems CBFW3のメーカー/サービスへの連絡先に関する情報。
Ratoc Systems CBFW3についてご質問がありますか？
次のフォームを使用してください
見つけた説明書を読んでもRatoc Systems CBFW3の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがRatoc Systems CBFW3で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。