Toshiba JK Seriesの取扱説明書

23ページ 2.6 mb
ダウンロード

ページに移動 of 23

Summary
  • Toshiba JK Series - page 1

    JK Series POWER DISTRIBUTION 400A & 720A Fixed T ype Medium V oltage Motor Contr ollers ...

  • Toshiba JK Series - page 2

    The low voltage section is oversized and is at a convenient height. This section is isolated from the medium voltage section and includes: Thermal Overload Protection Relay Pilot Lights (door mounted) Push Buttons (door mounted) Single Phase Ammeter (door mounted) CPT Secondary Fuses Control T erminal Points for Customer Connections T imers (for Re ...

  • Toshiba JK Series - page 3

    T oshiba's JK400 series complies with EEMAC, NEMA, UL and CSA standards and is available in non-reversing and reversing full voltage, autotrans- former , reactor , multi-speed, synchronous and wound rotor configurations. Latched contactors are also available. The JK400 series is available in the following enclosed ratings: 360 amps 2300-6600 V ...

  • Toshiba JK Series - page 4

    MEDIUM VOL T AGE CONTROLLERS JK720 Series The new JK720 Series of motor controller is the result of extensive research and development. This state-of-the-art controller was designed in Houston, T exas, and is currently being manufac- tured under ISO 9001 standards in the same manufacturing facility as T oshiba motors and drives. The components in t ...

  • Toshiba JK Series - page 5

    T oshiba's JK720 series complies with EEMAC, NEMA, UL and CSA standards and is available in non-reversing and reversing full voltage, autotrans- former , reactor , multi-speed, synchronous and wound rotor configurations. Latched contactors are also available. The JK720 series is available in the following enclosed ratings: 720 amps 2300-4800 V ...

  • Toshiba JK Series - page 6

    JK Series Product Specification 400A MEDIUM VOLTAGE FIXED CONTROLLER 1. Standards 1.1 Basic controller shall comply with NEMA ICS3-1993, Part 2 (ICS2-324) and UL 347 Standards. Basic controller can be UL Listed and CSA Certified. 2. Structure 2.1 Dimensions FVNR One-high - 30"W x 36"D x 46"H (no bus, small LV compartment) FVNR One-hi ...

  • Toshiba JK Series - page 7

    2.4 Handling and Installation 2.4.1 Removable angles or eye bolts shall be pr ovided at the top of t he structure for lifting. 3. Pow er Bus 3.1 Horizontal power bus shall be located at the cent er rear of the cubicle, in the same location as other JK Series controllers. 3.2 Horizontal power bus ratings of 1200 and 2000 amperes are available. Bus s ...

  • Toshiba JK Series - page 8

    4.2 Bolted Pressure Isolation Switch 4.2.1 A Toshiba type JK fixed mounted, gang-oper ated isolation switch shall be provided with each controller to isolate the medium vo ltage compartment from the power source. 4.2.2 The switch shall be directly driven by an externally operable handle mounted on the right hand flange of the cubicle. The handle sh ...

  • Toshiba JK Series - page 9

    4.3.3 Power connections from the isolation switch to the main power fuses shall be made using bus bar. Connections from the contactor through the current transformers to the outgoing load terminals shall be made using power cable furnished by others. 4.3.4 The contactor shall be available with an optional mechanical latch with provisions for manual ...

  • Toshiba JK Series - page 10

    5. Ratings 5.1 Controller shall be rated as follows: 5.1.1 Interrupting Ratings: 400 Ampere Controller: - contactor 7.0kA @ 6.9kV - fused controller 50kA RMS Sym. @ 7.2kV 200MVA @ 2.3kV 350MVA @ 4.0kV 400MVA @ 4.6kV 570MVA @ 6.6kV 5.1.2 Continuous Thermal Ratings: 400 Ampere Controller: Enclosure type Max. Continuous Amperes 46” and 61” One-hig ...

  • Toshiba JK Series - page 11

    JK Series Product Specification 720A MEDIUM VOLTAGE FIXED CONTROLLER 1. Standards 1.1 Basic controller shall comply with NEMA ICS3-1993, Part 2 (ICS2-324) and UL 347 Standards. Basic controller can be UL/CUL Listed. 2. Structure 2.1 Dimensions Across-the-Line (one-high) - 36"W x 36"D x 90"H Reduced Voltage Autotransformer - (2) 36&qu ...

  • Toshiba JK Series - page 12

    2.4.1 Removable angles or eye bolts shall be pr ovided at the top of t he structure for lifting. 2.4.2 Optional removable sill channels shall be available. 3. Pow er Bus 3.1 Horizontal power bus shall be located at the cent er rear of the cubicle, in the same location as other JK Series controllers. 3.2 Horizontal power bus ratings of 1200 and 2000 ...

  • Toshiba JK Series - page 13

    4.2 Bolted Pressure Isolation Switch 4.2.1 A fixed mounted, gang-operated isolation sw itch shall be provided with each controller to isolate the medium voltage compartment from the power source. 4.2.2 The switch shall be directly driven by an externally operable handle mounted on the right hand flange of the cubicle. The handle shall provi de posi ...

  • Toshiba JK Series - page 14

    4.3.3 Power connections from the isolation switch to the contactor shall be made using bus bar. Connections from the contactor through the curr ent transformers to the outgoing load terminals shall be made using power cable. 4.3.4 The contactor shall be supplied with an optional mechanical latch with provisions for manual or electrical trip. 4.3.5 ...

  • Toshiba JK Series - page 15

    4.5.7 An electrical interlock shall be provided to ensure the isolation switch does not open with the control power transformer under load. This interlock shall be designed such that during switch opening, the transformer secondary is disconnected prior to the opening of the switch blades. Also, during switch closing, the swit ch blades must close ...

  • Toshiba JK Series - page 16

    ...

  • Toshiba JK Series - page 17

    ...

  • Toshiba JK Series - page 18

    ...

  • Toshiba JK Series - page 19

    ...

  • Toshiba JK Series - page 20

    ...

  • Toshiba JK Series - page 21

    ...

  • Toshiba JK Series - page 22

    ...

  • Toshiba JK Series - page 23

    Medium V oltage Motor G7 Drive *pacjKSBROCH050218* ADJUST ABLE SPEED DRIVES MOTORS CONTROLS UPS INSTRUMENT A TION PLC INDUSTRIAL DIVISION 13131 W est Little Y ork Road, Houston, T exas 77041 T el 713/466-0277 Fax 713/466-8773 US 800/231-1412 Canada 800/872-2192 Mexico 01/800/527-1204 www .tic.toshiba.com Copyright 2/2005 A vailable Through: TOSHIBA ...

メーカー Toshiba カテゴリー Power Supply

Toshiba JK Seriesのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- JK Seriesの取扱説明書
- Toshibaの製品カード
- パンフレット
- またはToshiba JK Seriesの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Toshiba JK Seriesの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Toshiba JK Seriesの取り付け説明書、サービスマニュアル、簡易説明書、またはToshiba JK Seriesのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Toshiba JK Seriesの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Toshiba JK Seriesデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがToshiba JK Seriesを使用するのを助ける技術的文書のことです。説明書は通常、全てのToshiba JK Seriesユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Toshibaの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Toshiba JK Seriesの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははToshiba JK Seriesの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Toshiba JK Seriesに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Toshiba JK Seriesデバイスの基本機能を使うにあたってのヒント。 Toshiba JK Seriesのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Toshiba JK Seriesに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるToshiba JK Seriesのメーカー/サービスへの連絡先に関する情報。

Toshiba JK Seriesについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもToshiba JK Seriesの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがToshiba JK Seriesで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)