Wagner SprayTech 770の取扱説明書

26ページ 3.16 mb
ダウンロード

ページに移動 of 26

Summary
  • Wagner SprayTech 770 - page 1

    Français - p. 25 Español - p. 49 Owner’ s Manual Contents Before Y ou Start 2 Important Safety Information 4 What’s in the Box 5 Assemble Y our Wagner Paint Crew Using the Wagner P aint Crew 6 Proper Use and Functions 7 Pressure Relief Procedure 8 Load Material 9 Getting Material to Flow Prior to Spraying 10 Practice Spraying Tips if Experien ...

  • Wagner SprayTech 770 - page 2

    Important Safety Information Read all safety information before operating the equipment. Save these instructions to PRIME to relieve the pressure. Refer to the Pressure Relief Procedure (page 7) described in the pump manual. • AL W A YS keep the tip guard in place while spraying. The tip guard provides some protection but is mainly a warning devi ...

  • Wagner SprayTech 770 - page 3

    Grounded outlet Grounded pin Cover for grounded outlet box • This product may be used only with water-based materials or materials with a minimum ash point of 70ºF (21ºC) for spraying or cleaning. Do not spray or clean with materials having a ash point less than 70ºF (21ºC), such as solvent based lacquers, enamels, and/or stain blockers ...

  • Wagner SprayTech 770 - page 4

    SPRAY PRIME O l Spray Hose T rigger T rigger Lock Spray T ip Assembly Spray Hose Fitting The Spray Gun Hopper Lid Spray Hose Outlet ON/OFF Switch Hopper Material Return T ube PRIME/SPRA Y Knob Handle Handle Hardware Inlet Filter The Paint Crew Fill Line Questions? Call W agner T echnical Service 1-800-328-8251 Register your product online at: www . ...

  • Wagner SprayTech 770 - page 5

    3. On each side of the handle install bolt and tighten wing nut over lock washer 2. Insert handle Start 1 Start 1 Assemble Y our W agner Paint Crew What you’ll need • Phillips screwdriver • Wrench (2) Note: Do not plug in the power cord until assembly is complete. 4. Thread one end of spray hose to outlet valve on sprayer 5. T ighten with wre ...

  • Wagner SprayTech 770 - page 6

    SPRAY PRIME O l Proper Use and Functions Specications Weight . . . . . . . . . . . . . . . . . . . 25 lbs Capacity . . . . . . . . . . . . . . . . . . 2 gallon hopper Power source . . . . . . . . . . . . . . ½ Hp universal motor Power requirement . . . . . . . . . . 15 amp minimum circuit on 120 V AC, 60 Hz current Generator . . . . . . . . . . ...

  • Wagner SprayTech 770 - page 7

    l O Start Important Safety W arning Be careful when handling the spray gun so you don’t accidently spray yourself. The high pressure paint stream could pierce your skin causing serious injury . If an accident happens see detail procedures in the Safety Information section on pages 4-5. See physician immediately and bring this instruction manual. ...

  • Wagner SprayTech 770 - page 8

    l O l O ON OFF HOPPER LID Start 1. Load Material What you’ll need • The material you plan to spray • Extension cord • Waste container 2. Push tab on lter twice to test inlet valve operation 3. Fill hopper TIP: If material is old, strain when pouring into hopper to help prevent clogging when spraying 4. Plug in sprayer 5. T urn knob ...

  • Wagner SprayTech 770 - page 9

    SQUEEZE l O ON L O C K What you’ll need • Scrap material/cardboard • Drop cloths to protect oors and furnishings from overspray Special Note Don’t let the hopper run empty . If the hopper runs empty go to page 8 “Load Material” and page 9 “Get - ting Material to Flow “ and follow the steps as shown 2. Getting Material to Fl ...

  • Wagner SprayTech 770 - page 10

    GOOD JOB! Hold the Spray Gun Level BAD Start 3. Practice Spraying What you’ll need • Scrap material/cardboard GOOD JOB! Practice on a piece of scrap material/cardboard T ip: T rigger gun after starting the stroke. Release the trigger before ending the stroke. The spray gun should be mov- ing when the trigger is pulled and released. Overlap e ...

  • Wagner SprayTech 770 - page 11

    Start stroke End stroke Pull trigger Release trigger Move steadily ! GOOD JOB! BAD Spray T echnique Spray P attern GOOD SPRA Y P A TTERN BAD SPRA Y P A TTERN: T AILING GOOD JOB! Overlap Y our Strokes See page 12 Using the W agner P aint Crew Using the Wagner Paint Crew • Practice Spraying English 11 ...

  • Wagner SprayTech 770 - page 12

    If material isn’t flowing properly after clearing these things see additional instructions in the Fix Spraying Problems section Page 22 Common Solutions to Spraying Issues Keep material owing smoothly while spraying Straining material when loading hopper helps minimize clogging If experiencing issues with spray patterns or if material isn’t ...

  • Wagner SprayTech 770 - page 13

    L O C K l O 3 Note: If spray tip is difcult to rotate relieve pressure by turning PRIME/SPRA Y knob to PRIME and squeeze trigger while pointing at scrap material/cardboard. Release trigger and try rotating spray tip again l O ON U N L O C K 1 Start 1 Clear the Spray Tip 2. Release trigger and lock spray gun 3. T urn power OFF What you’ll need ...

  • Wagner SprayTech 770 - page 14

    HANDLE HANDLE Start IMPORT ANT : Never clean lter by poking with sharp object . Perform Pressur e Relief Procedur e Page 7 4. Remove inlet lter from hopper 3. Empty material from hopper into original material container 7. T o resume painting follow: Load Material and Get Material to Flow instructions Page 8-9 INLET FIL TER Clean the Inlet Fil ...

  • Wagner SprayTech 770 - page 15

    Start 1 Clean the Spray Gun Filter What you’ll need • Wrench • Warm, soapy water for latex material • Mineral spirits for oil based materials • Replacement spray gun lter (if necessary) 5. Remove lter from housing 9. Reassemble spray gun 8. Replace cleaned lter , tapered end rst, into gun housing. Note: It is impor ...

  • Wagner SprayTech 770 - page 16

    HOPPER LID 5. If your break is more than an hour slowly pour ½ cup of water of paint in hopper . This helps prevent paint from drying and causing possible clogs 6. Place lid on hopper and keep sprayer out of sun Instructions are for latex material only Note: If using oil based material follow instructions for Cleanup and Storage on page 18 This pr ...

  • Wagner SprayTech 770 - page 17

    4. Steps for Getting Material to Flow ( page 9 ) 3. If water was added during shut down stir water into material 2. Remove spray gun from plastic bag or from bucket of water Startup from Short T erm Storage What you’ll need • Stir stick Start 4 3 2 Page 9 1 OR English 17 Cleanup and Storage • Startup from Short-T erm Storage Cleanup and St ...

  • Wagner SprayTech 770 - page 18

    l O SQUEEZE T U R N ON HANDLE HANDLE l O OFF Flush Material From Sprayer 12. T urn knob to PRIME and squeeze trigger until pressure is relieved. Release trigger , lock spray gun, turn power OFF 11. Continue squeezing trigger until uid is coming out clear . Repeat as necessary 8. Squeeze trigger 9. T urn power ON 10. T urn knob to SPRA Y 6. Fill ...

  • Wagner SprayTech 770 - page 19

    l O l O ON OFF 2-3 MINUTES 3. Remove inlet lter and clean with appropriate cleaning solution. Replace inlet lter in hopper 9. Hold material return tube over a waste container . Run for 2 to 3 minutes 10. T urn power OFF 7. T urn knob to PRIME 8. T urn power ON 4. Partially ll hopper with NEW cleaning solution 2. Rinse hopper with appropria ...

  • Wagner SprayTech 770 - page 20

    HOUSEHOLD OIL HOUSEHOLD OIL Start Clean Spray Gun Components What you’ll need • Soft bristled brush • Light household oil • W arm, soapy water if using latex material • Mineral spirits for oil based material • Wrench 4. Remove lter from spray gun 7. Install gun lter tapered-end rst. Reassemble spray gun 6. Pour a few drops of l ...

  • Wagner SprayTech 770 - page 21

    l O ON OFF 5 SECONDS HOUSEHOLD OIL HOUSEHOLD OIL l O Start 1 Long T erm Storage 2. Remove inlet lter 4. Cover outlet valve with a rag. T urn power ON . Let run for 5 seconds 5. T urn power OFF 7. Wipe entire unit, hose and spray gun with damp cloth to remove accumulated material INLET FIL TER Start What you’ll need • Light household oil ? ...

  • Wagner SprayTech 770 - page 22

    Before servicing, always r elease system pressur e by following Pressur e Relief Procedur e (page 7). Problem A: The sprayer does not start Cause Solution 1. Sprayer is not plugged in Plug sprayer in 2. ON/OFF switch is set to OFF T ur n ON/OFF switch to ON 3. The sprayer shuts off while under pr essure Motor will cycle ON and OFF while spraying to ...

  • Wagner SprayTech 770 - page 23

    Problem D: The PRIME/SPRA Y knob is set to SPRA Y and there is flow thr ough the material return tube Cause Solution 1. The PRIME/SPRA Y valve is dirty or worn T ake sprayer to Wagner Authorized Service Center Problem E: The spray gun leaks Cause Solution 1. Gun lter housing is loose Tighten handle 2. Internal parts of spray gun are worn or dir ...

  • Wagner SprayTech 770 - page 24

    Inlet fitting O-ring Inlet fitting O-ring Inlet fitting O-ring Inlet fitting Inlet valve Inlet valve O-ring 2. Remove inlet lter from bottom of hopper 4. Inspect the three inlet tting O-rings and replace if worn. If not replacing O-rings do not remove them but clean with appropriate cleaning solution based on material being used. Lubricate wi ...

  • Wagner SprayTech 770 - page 25

    Español 74 Français 74 English 74 4 8 5 1 3 2 7 6 6 1 2 3 4 5 6 9 Spray Gun • Pistolet • Pistola Sprayer • Pulvérisateur • Rociador Item Article Articulo Part No. No de piéce Pieza No. English - Description Français - Description Español - Descripción Quantity Quantite Cantidad 1 0515223 Hopper lid Couvercle de trémie T apa de tolva ...

  • Wagner SprayTech 770 - page 26

    W arranty • Garantie • Garantía Español 75 Français English Limited Warranty AIRLESS P AINT SPRA Y EQUIPMENT This product, manufactured by W agner Spray T ech Corporation (W agner), is warranted to the original retail purchaser against defects in material and workmanship for one year from date of purchase. This warranty does not cover damage ...

メーカー Wagner SprayTech カテゴリー Paint Sprayer

Wagner SprayTech 770のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 770の取扱説明書
- Wagner SprayTechの製品カード
- パンフレット
- またはWagner SprayTech 770の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Wagner SprayTech 770の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Wagner SprayTech 770の取り付け説明書、サービスマニュアル、簡易説明書、またはWagner SprayTech 770のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Wagner SprayTech 770の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Wagner SprayTech 770デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがWagner SprayTech 770を使用するのを助ける技術的文書のことです。説明書は通常、全てのWagner SprayTech 770ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Wagner SprayTechの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Wagner SprayTech 770の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははWagner SprayTech 770の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Wagner SprayTech 770に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Wagner SprayTech 770デバイスの基本機能を使うにあたってのヒント。 Wagner SprayTech 770のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Wagner SprayTech 770に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるWagner SprayTech 770のメーカー/サービスへの連絡先に関する情報。

Wagner SprayTech 770についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもWagner SprayTech 770の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがWagner SprayTech 770で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)