Ryobi RY6202の取扱説明書

20ページ 0.93 mb
ダウンロード

ページに移動 of 20

Summary
  • Ryobi RY6202 - page 1

    OPERA T OR'S MANUAL 5-1/2 in. (140 mm), 14.4 VOL T CORDLESS CIRCULAR SA W MODEL NO. R Y6202 SA VE THIS MANUAL FOR FUTURE REFERENCE SPECIFICA TIONS: Blade Diameter 5-1/2 in. (140 mm) Blade Arbor 3/8 in. (10 mm) Cutting Depth at 0 ° 1-9/16 in. (40 mm) Cutting Depth at 45 ° 1-1/8 in. (29 mm) No Load Speed 3,800 RPM Motor 14.4 Volt DC Charge Rat ...

  • Ryobi RY6202 - page 2

    Page 2 Look for this symbol to point out important safety precautions. It means attention!!! Your safety is involved. The following recommended accessories are current and were available at the time this manual was printed. ■ 5-1/2 in. (140 mm) Thin Kerf Blade ■ Optional Rip Guide Your circular saw has been shipped completely assembled except f ...

  • Ryobi RY6202 - page 3

    Page 3 W ARNING: Read and follow all instructions. Failure to follow all instructions listed below , may result in electric shock, fire and/or serious personal injury . SA VE THESE INSTRUCTIONS W ork Area ■ Keep your work area clean and well lit. Cluttered benches and dark areas invite accident. ■ Do not operate power tools in explosive atmo- s ...

  • Ryobi RY6202 - page 4

    Page 4 Additional Rules For Safe Operation ■ Know your power tool. Read operator ’ s manual care- fully . Learn its applications and limitations, as well as the specific potential hazards related to this tool. Following this rule will reduce the risk of electric shock, fire, or serious injury . ■ Make sure your extension cord is in good condi ...

  • Ryobi RY6202 - page 5

    Page 5 SPECIFIC SAFETY RULES Additional Specific Safety Rules Continued ■ Never use damaged or incorrect blade washers or bolts. The blade washers and bolt were specially de- signed for your saw , for optimum performance and safety of operation. ■ Causes and Operator Prevention of Kickback: Kickback is a sudden reaction to a pinched, bound, or ...

  • Ryobi RY6202 - page 6

    Page 6 ■ To reduce the risk of damage to charger body and cord, pull by charger plug rather than cord when disconnecting charger . Following this rule will reduce the risk of serious personal injury . ■ Make sure cord is located to that it will not be stepped on, tripped over , or otherwise subjected to damage or stress. Following this rule wil ...

  • Ryobi RY6202 - page 7

    Page 7 The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and the explanations with them, deserve your careful attention and understanding. The safety warnings do not by themselves eliminate any danger. The instructions or warnings they give are not substitutes for proper accident prevention measures ...

  • Ryobi RY6202 - page 8

    Page 8 KNOW YOUR CORDLESS CIRCULAR SAW See Figure 1. Before attempting to use any tool, familiarize yourself with all operating features and safety requirements. Features include easily operated bevel cut and depth of cut adjustment mechanisms; positive 0 ° bevel stop; spindle lock; and blade wrench storage. APPLICATIONS (Use only for the purpose ...

  • Ryobi RY6202 - page 9

    Page 9 Fig. 2 IMPORTANT CHARGER INFORMATION The battery pack for this Circular Saw, should be charged only with charger provided. The charger part number will be found on a plate located on the bottom of the charger. Before using the charger, it is extremely important that you familarize yourself with the LED functions of the charger. See Figure 2 ...

  • Ryobi RY6202 - page 10

    Page 10 45 45 50 50 3 0 30 22 22 1 1 2 3 0 45 W ARNING: Always remove battery pack from your saw when you are assembling parts, making adjustments, assembling or removing blades, cleaning, or when not in use. Re- moving battery pack will prevent accidental starting that could cause serious personal injury . TO REMOVE BATTERY PACK ■ Locate latches ...

  • Ryobi RY6202 - page 11

    Page 11 45 4 5 50 5 0 30 30 22 22 1 1 2 3 0 45 Fig. 6 BLADE SCREW BLADE WRENCH SPINDLE LOCK BUTTON ■ Fit saw blade inside lower blade guard and onto spindle. NOTE: The saw teeth point upward at the front of saw as shown in figure 5. ■ Replace outer blade washer . ■ Depress spindle lock button, then replace blade screw . T ighten blade screw s ...

  • Ryobi RY6202 - page 12

    Page 12 KICKBACK See Figure 8. The best guard against kickback is to avoid dangerous practices. Kickback occurs when the blade stalls rapidly and the saw is driven back towards you. Blade stalling is caused by any action which pinches the blade in the wood. W ARNING: To avoid kickback, release switch immediately if blade binds or saw stalls. Kickba ...

  • Ryobi RY6202 - page 13

    Page 13 ■ When making a cut use steady, even pressure. Never force cuts. ■ Do not cut warped or wet lumber. ■ Always hold your saw firmly with both hands and keep your body in a balanced position so as to resist the forces of kickback should it occur. When using your saw, always stay alert and exercise control. Do not remove your saw from wor ...

  • Ryobi RY6202 - page 14

    Page 14 TO HELP MAINTAIN CONTROL: ■ Always support your workpiece near the cut. ■ Support your workpiece so the cut will be on your left. ■ Clamp your workpiece so it will not move during the cut. Place your workpiece with its good side down. NOTE: The good side is the side on which appearance is important. Before beginning a cut, draw a guid ...

  • Ryobi RY6202 - page 15

    Page 15 TO CROSS CUT OR RIP CUT When making a cross cut or rip cut, align your line of cut with the outer blade guide notch on the saw base as shown in figure 17. Since blade thicknesses vary, always make a trial cut in scrap material along a guideline to determine how much, if any, the guideline must be offset to produce an accurate cut. NOTE: The ...

  • Ryobi RY6202 - page 16

    Page 16 TO BEVEL CUT The angle of cut of your saw may be adjusted to any desired setting between zero and 50 ° . NOTE: When making cuts at 50 ° , blade should be set at full depth of cut. When making 45 ° bevel cuts, there is a notch in the saw base to help you line up the blade with the line of cut. See Figure 19. Align your line of cut with th ...

  • Ryobi RY6202 - page 17

    Page 17 1 2 45 0 0 15 22 30 45 50 45 4 5 50 5 0 30 30 22 22 POSITIVE 0 ° BEVEL STOP See Figure 21. Your saw has a positive 0 ° bevel stop, that has been factory adjusted to assure 0 ° angle of your saw blade when making 90 ° cuts. However, misalignment can occur during shipping. TO CHECK ■ Remove battery pack from saw. W ARNING: Failure to re ...

  • Ryobi RY6202 - page 18

    Page 18 45 45 50 50 30 30 22 22 TO RIP CUT OPTIONAL RIP GUIDE (EDGE GUIDE) See Figure 23. Use a guide when making long or wide rip cuts with your saw. An optional rip guide with a five inch scale is available or you can make an efficient rip guide by clamping a straight edge to your workpiece. Secure the workpiece. Using C-clamps, firmly clamp a st ...

  • Ryobi RY6202 - page 19

    Page 19 W ARNING: When servicing, use only identical replacement parts. Use of any other part may create a hazard or cause product damage. W ARNING: Do not at any time let brake fluids, gasoline, petroleum- based products, penetrating oils, etc. come in contact with plastic parts. They contain chemicals that can damage, weaken or destroy plastic. B ...

  • Ryobi RY6202 - page 20

    983000-191 9 -03 • SER VICE Now that you have purchased your tool, should a need ever exist for repair parts or service, simply contact your nearest Ryobi Authorized Service Center. Be sure to provide all pertinent facts when you call or visit. Please call 1-800-525-2579 for your nearest Ryobi Authorized Service Center. You can also check our web ...

メーカー Ryobi カテゴリー Saw

Ryobi RY6202のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- RY6202の取扱説明書
- Ryobiの製品カード
- パンフレット
- またはRyobi RY6202の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Ryobi RY6202の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Ryobi RY6202の取り付け説明書、サービスマニュアル、簡易説明書、またはRyobi RY6202のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Ryobi RY6202の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Ryobi RY6202デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがRyobi RY6202を使用するのを助ける技術的文書のことです。説明書は通常、全てのRyobi RY6202ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Ryobiの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Ryobi RY6202の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははRyobi RY6202の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Ryobi RY6202に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Ryobi RY6202デバイスの基本機能を使うにあたってのヒント。 Ryobi RY6202のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Ryobi RY6202に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるRyobi RY6202のメーカー/サービスへの連絡先に関する情報。

Ryobi RY6202についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもRyobi RY6202の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがRyobi RY6202で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)