JBL SDEC-3000の取扱説明書

24ページ 2.52 mb
ダウンロード

ページに移動 of 24

Summary
  • JBL SDEC-3000 - page 1

    S YNTH ESIS ® SDEC-3000 SDEC-4000 D IGITAL E QUALIZER WITH DACS C ALIBRATION C HECKLIST & M ANUAL ...

  • JBL SDEC-3000 - page 2

    - 2 - SDEC -X000 DAC S Calibration M anual v1.0.doc 1 Introduction ................................................................................................... 4 2 Equipment Required: .................................................................................... 4 3 Calibration Checklist ................................................ ...

  • JBL SDEC-3000 - page 3

    - 3 - SDEC -X000 DAC S Calibration M anual v1.0.doc 11 Saving Your Work ...................................................................................... 20 11.1 Save a copy using SAVE AS ............................................................ 20 11.2 Save to Network Device ................................................................. ...

  • JBL SDEC-3000 - page 4

    - 4 - SDEC -X000 DAC S Calibration M anual v1.0.doc 1 Introduction W el come to the JBL Synthesis and DACS user guide. The below information is designed to help an installer use the SDEC and DACS kit to properly test and calibrate a room. This guide is designed to help guide you through the calibration process when using the original DACS Digital A ...

  • JBL SDEC-3000 - page 5

    - 5 - SDEC -X000 DAC S Calibration M anual v1.0.doc 3 Calibration Che cklist The calibration process is more than just measuring and applying EQ to achieve a preset target. It includes examining the entire signal chain and confirming that all parts of the system are accurately connected. Use the below checklist to make sure you hav e completed all ...

  • JBL SDEC-3000 - page 6

    - 6 - SDEC -X000 DAC S Calibration M anual v1.0.doc 4 SDEC Hardw are Connection Please refer to the SDEC Installers Manual for detailed hardware connection instructions and diagrams. Check the SDEC for correct connection using the below chart for SDEC-3000 and the next page for SDEC-4000 installations: • Make sure you have access to the SDEC-3000 ...

  • JBL SDEC-3000 - page 7

    - 7 - SDEC -X000 DAC S Calibration M anual v1.0.doc SDEC-4000 with Bi-Amplified Front s SDEC-4000 with Full-Range Fron ts Surround Proces sor to SDEC4000P Inputs Surround Processor to SDEC4000P I nputs S4000IC Number Channel SDE C4000P S4000IC Number C hannel SDEC4000P 1 Left Front A1 1 Left Front A1 2 Right Front A2 2 Right Front A2 3 Center Front ...

  • JBL SDEC-3000 - page 8

    - 8 - SDEC -X000 DAC S Calibration M anual v1.0.doc 4.2 Ethernet Connec tion For all SDEC-3000 installations you will need either a crossover Ethernet cable or the SDEC will need to be connected to an Ethernet hub (figure 3). For all SDEC-4000 installations both the SDEC-4000P and SDEC-4000X, as well as your computer must be connected to an Etherne ...

  • JBL SDEC-3000 - page 9

    - 9 - SDEC -X000 DAC S Calibration M anual v1.0.doc 5 Sof tw are Operation using the Java Remote The SDEC can be controlled and configured from any computer that has access to the network via Ethernet. All necessary features can be accessed and all system setup parameters can be viewed and adjusted using the JAVA remote but advanced features can on ...

  • JBL SDEC-3000 - page 10

    - 10 - SDEC -X000 DAC S Calibration M anual v1.0.doc 6 Sof tw are Operation using London Architect™ NOTE: While it is possible to use a WIFI access point to control and configure the SDEC we do not recommend using this method for initial setup when using London Architect. For the most reliable connection it is highly recommended that you use a wi ...

  • JBL SDEC-3000 - page 11

    - 11 - SDEC -X000 DAC S Calibration M anual v1.0.doc not have the file you should be able to retrieve it from the SDEC directly. NOTE : To access the design file you will need a user name and password • User Login: JBL Synthesis Dealer • Password: synthesis . Figure 9. 6.2.2 Opening from a Netw ork Device The SDEC allows you to use the unused p ...

  • JBL SDEC-3000 - page 12

    - 12 - SDEC -X000 DAC S Calibration M anual v1.0.doc 6.3 ONLINE Mode W he n in ONLINE mode you are actively controlling the SDEC-3000 or SDEC-4000. The SDEC-4000 can be configured for Full Range (factory default) or Bi-amp mode. The SDEC-4000 is set to full range to ensure that the bi-amp speakers without built in crossovers will not be damaged acc ...

  • JBL SDEC-3000 - page 13

    - 13 - SDEC -X000 DAC S Calibration M anual v1.0.doc 6.3.2 EQ Contr ols Entering the EQ settings can be accomplished simply by clicking inside the boxes and typing in your settings. Any channel can be accessed by selecting from the channel list on the left. Figure 12. Click on the channel button to show the EQ available Enter the EQ filter settings ...

  • JBL SDEC-3000 - page 14

    - 14 - SDEC -X000 DAC S Calibration M anual v1.0.doc 6.3.3 Channel Delay (Speaker Di stance Offset Correc tion) Do not enter the distance measured into the channel distance box. Use the lo ngest measur ed distance as your 0 reference and SUBTRACT each speaker distance from this reference. This result is the number you should ent er. For ex am ple: ...

  • JBL SDEC-3000 - page 15

    - 15 - SDEC -X000 DAC S Calibration M anual v1.0.doc 6.3.4 Channel Output Use each output to adjust each channel to give the same output level using an SPL meter. 6.3.5 Le vel Matching Multiple Sur round and Subw oofer Channels The SDEC-4000 has multiple outputs for Subwoofers and Side Surrounds. These will need to be level matched to each other be ...

  • JBL SDEC-3000 - page 16

    - 16 - SDEC -X000 DAC S Calibration M anual v1.0.doc 7 Speaker Sound Check Use the circulating noise generator of the Surround Processor to confirm that all channels have output and that each speaker is connected to its corresponding channel. 8 Speaker Phase T est This procedure uses the Surround Processor to route the phase tester's output to ...

  • JBL SDEC-3000 - page 17

    - 17 - SDEC -X000 DAC S Calibration M anual v1.0.doc 8.2.2 Dipole S urrounds Regardless of model there is one standard for phase configuration of Dipole surrounds. Figure 16. 8.2.3 Direct R adiating Point Sourc e Surrounds Figure 17. 8.3 Using the Phase Tester The Galaxy Audio phase tester consists of two battery operated instruments, Cricket-S is ...

  • JBL SDEC-3000 - page 18

    - 18 - SDEC -X000 DAC S Calibration M anual v1.0.doc 9 Setting Output Level 9.1 Setting Levels before Calibra ting Using the internal noise generator of the SDP set all output s to achieve 75dB using the “C” weighting and “SLOW ” re sponse. This will maintain the best signal to noise and headroom possible by optimizing the gain structure of ...

  • JBL SDEC-3000 - page 19

    - 19 - SDEC -X000 DAC S Calibration M anual v1.0.doc 10 DACS Measure ment System 10.1 DACS Hardware Setup Unpack the DACS Kit and setup the microphone array. Make all standard connections except for connecting to the SDEC. Use the below diagram as a guide. Note: Please refe r to the DACS m anual that comes with the DACS K it for detailed inst ructi ...

  • JBL SDEC-3000 - page 20

    - 20 - SDEC -X000 DAC S Calibration M anual v1.0.doc 10.2.1 Parametric Filter V alues Figure 20. 11 Saving Y o ur Work The SDEC-3000 and SDEC-4000 DO NOT REQUIRE that you save at any time. When you are online and operating the unit your settings are being stored in protected memory at all times and no save process is required or possible. Saving yo ...

  • JBL SDEC-3000 - page 21

    - 21 - SDEC -X000 DAC S Calibration M anual v1.0.doc 13 A d v anced Features 13.1 Cinema/Music Su bwoofer Output The SDEC has the ability to change the subwoofer output gain to accommodate both the standard cinema curve and a more linear music output level. This feature has been built into the SDEC as a simple alternative to the multiple EQ presets ...

  • JBL SDEC-3000 - page 22

    - 22 - SDEC -X000 DAC S Calibration M anual v1.0.doc Figure 21. Figure 22. Figure 23. ...

  • JBL SDEC-3000 - page 23

    - 23 - SDEC -X000 DAC S Calibration M anual v1.0.doc 14 T r oubleshooting Guide Symptom Probable Cause Solution Cannot see the units in the Network control panel Wrong network card selected Check IP properties in application preferences Ethernet cable unplugged Check connections “No Matched Devices Found” Wrong network card selected Check IP pr ...

  • JBL SDEC-3000 - page 24

    - 24 - SDEC -X000 DAC S Calibration M anual v1.0.doc ...

メーカー JBL カテゴリー Stereo Equalizer

JBL SDEC-3000のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- SDEC-3000の取扱説明書
- JBLの製品カード
- パンフレット
- またはJBL SDEC-3000の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、JBL SDEC-3000の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、JBL SDEC-3000の取り付け説明書、サービスマニュアル、簡易説明書、またはJBL SDEC-3000のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、JBL SDEC-3000の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

JBL SDEC-3000デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがJBL SDEC-3000を使用するのを助ける技術的文書のことです。説明書は通常、全てのJBL SDEC-3000ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

JBLの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. JBL SDEC-3000の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははJBL SDEC-3000の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。JBL SDEC-3000に関してこのドキュメントで見つけることができる全てのヒントの目次
3. JBL SDEC-3000デバイスの基本機能を使うにあたってのヒント。 JBL SDEC-3000のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。JBL SDEC-3000に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるJBL SDEC-3000のメーカー/サービスへの連絡先に関する情報。

JBL SDEC-3000についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもJBL SDEC-3000の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがJBL SDEC-3000で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)