Craftsman 536,884,791の取扱説明書

19ページ 0.73 mb
ダウンロード

ページに移動 of 19

Summary
  • Craftsman 536,884,791 - page 1

    5.0 Horsepower 22 Inch Dual Stage 120V, Electric Start SNOW THROWER MODEL NO, 536,884791 Caution: Read and follow all Safety Rules and Operating Instructions before first use of this product, SEARS, ROEBUCK AND CO., Hoffman Estates, IL 60179 U.S.A. F-O01070J 07/27/99 ...

  • Craftsman 536,884,791 - page 2

    il nP':_:) H= [o]= [o,[o]'_lld=l_',] Table of Contents 2 Service and Adjustments 14-t6 Warranty 2 Storage 17 Safety Rules 2-4 Troubleshooting 18 Contents of Shipping Carton 4-5 Repair Parts 20-26 Assembly 5-7 Engine Repair Parts 27-31 Operation 8-12 Spanish (Espa5ol) 32-51 Maintenance 12-14 Parts Ordedng,'Service Back Cover LIMI ...

  • Craftsman 536,884,791 - page 3

    PREPARATION 1. Thoroughly inspect the area where the snow thrower is to be used and remove all doormats, sleds, boards, wires and other foreign objects. 2. Disengage all clutches before starting the engine (motor). 3. Do not operate the snow thrower without wearing adequate winter outer garments. Wear footwear that will improve footing on slippery ...

  • Craftsman 536,884,791 - page 4

    16. Never direct discharge at bystanders or allow anyone in front of the snow thrower. 17. Disengage power to the auger/impeller when snow thrower is transported or not in use. 18. Use only attachments and accessories approved by the manufacturer of the snow thrower (such as tire chains, electric start kits, etc). 19. Never operate the snow thrower ...

  • Craftsman 536,884,791 - page 5

    Parts packed separately in carton (not shown full size) 2 - Ignition Keys (Attached to engine in plastic bag) 1 - Crank Assembly 1 - Snow Chute Assembly ,4k CAUTION: Always wear safety glasses or eye shields while assembling snow thrower. TOOLS REQUIRED FOR ASSEMBLY 1 - Knife (to cut carton and plastic ties) 2- 1/2 inch wrenches (or adjustable wren ...

  • Craftsman 536,884,791 - page 6

    • Remove and discard the packing material from around the snowthrower. • Cut all four corners of the carton from top to bottom and lay the panels flat. • Cut ties securing the clutch control cable to the lower handle and lay cable back away from the motor frame. • Standing at rear, tilt snowthrower forward and remove packaging under motor f ...

  • Craftsman 536,884,791 - page 7

    • Carefully remove cotter pin, clevis pin and drilled pin from yoke end of crank rod assembly (see figure below). • Place universal joint into end of worm gear lining up large holes. Insert drilled pin (ensure opening in pin is in line with small openings in universal joint) (see figure below). • Place yoke end of crank rod around universal j ...

  • Craftsman 536,884,791 - page 8

    Eo to] KNOW YOUR SNOW THROWER READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR SNOW THROWER. Compare the illustrations with your SNOW THROWER to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. r Drive Lever Primer Button Electric Starter Button Discharge Ignition ...

  • Craftsman 536,884,791 - page 9

    Auger Drive Clutch Ignition Key insert to run pull out to stop Z_ CAUTION: Read owner's manual before operating machine. Never direct discharge toward bystanders. Release the auger control bar and stop the engine before unclogging discharge chute or auger housing and before leaving the machine. The operation of any snow thrower can re- sult in ...

  • Craftsman 536,884,791 - page 10

    BEFORE STARTING THE ENGINE • If the snow thrower must be moved with- out the aid of the engine, it is easier to pull the snow thrower by the handles rather than pushing. • Before you service or start the engine, fa- miliarize yourself with the snow thrower. Be sure you understand the function and location of all controls. NOTE: Check tension of ...

  • Craftsman 536,884,791 - page 11

    COLD START (See figure on this page) • Be sure the auger ddve lever is in the disengaged (Released) position, • Move the throttle control to '_ (Fast) position. • Remove the keys from the plastic bag. Insert one key into the ignition slot. Be sure it snaps into place. DO NOT TURN KEY. Keep the second key in a safe place. • Rotate the c ...

  • Craftsman 536,884,791 - page 12

    • Push the primer button, see figure on page 8, while covering the vent hole as follows: (remove finger from primer but- ton between primes). One time if temperature is above 50oF. Two times if temperature is 50_F to 15°t:. Four times if temperature is below 15°F. • Pull the recoil starter handle rapidly. Do not allow the handle to snap back, ...

  • Craftsman 536,884,791 - page 13

    CUSTOMER RESPONSIBILITIES SERVICE RECORDS Fill in dates as you complete regular service Check Engine Oil Level Change Engine Oil Tighten All Screws & Nuts Lubricate Pivot Points Check Auger Clutch Cable Adjustment (See Cable Adj) Check Ddve Bert Check Fuel Drain Fuel Replace Spark Plug After first 2 Hours SCHEDULE SERVICE DATES Before AS Every ...

  • Craftsman 536,884,791 - page 14

    OIL RECOMMENDATION Only use high quality detergent oil rated with API service classification SG. Select the oil's viscosity grade according to your expected operating temperature. NOTE: For extreme cold operating condi- tions of 0 ° and below, use a partial synthetic OW30 motor oil for easier starting. NOTE: Although multi-viscosity oils im- ...

  • Craftsman 536,884,791 - page 15

    • Hold the square end of the threaded portion with pliers and adjust the Iocknut in or out until the excess slack is removed (see last figure on page 14). • Pull the cable back through the spring and connect the cable (see last figure on page 14). NOTE: Whenever the auger belt is replaced, the cables will need to be adjusted. TO ADJUST AUGER DR ...

  • Craftsman 536,884,791 - page 16

    mounting bolt. • Reinstall the belt cover. • Reconnect the spark plug wire. A(_dve Pulley " ,_._,,,,=_. Belt Guide ,--k -'-k" .8. Auger Idler _ Pulley Enga_ it _ _ . Impeller _ Pulley TO REPLACE AUGER SHEAR BOLT The augers are secured to the auger shaft with special bolts (see figure below ) that are designed to break (to prot ...

  • Craftsman 536,884,791 - page 17

    Z_ CAUTION' Never store your snow thrower indoors'or in an enclosed, poorly ventilated area if gasoline remains in the tank. fumes may reach an open flame, spark or pilot light from a furnace, water heater, clothes dryer, cigarette, etc. To prevent engine damage (if snow thrower is not used for more than 30 days) follow the steps below. S ...

  • Craftsman 536,884,791 - page 18

    TROUBLE CAUSE CORRECTION )ifficult starting Defective spark plug Replace spark plug Water or dirt in fuel system Use carburetor bowl drain to flush and refill with fresh fuel. Engine runs Blocked fuel line or low on fuel Clean fuel line; check fuel supply; erratically tank or stale gasoline add fresh fuel (gasoline/oil mix tura if 2-cycle engine). ...

  • Craftsman 536,884,791 - page 19

    19 ...

メーカー Craftsman カテゴリー Snow Blower

Craftsman 536,884,791のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 536,884,791の取扱説明書
- Craftsmanの製品カード
- パンフレット
- またはCraftsman 536,884,791の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Craftsman 536,884,791の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Craftsman 536,884,791の取り付け説明書、サービスマニュアル、簡易説明書、またはCraftsman 536,884,791のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Craftsman 536,884,791の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Craftsman 536,884,791デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがCraftsman 536,884,791を使用するのを助ける技術的文書のことです。説明書は通常、全てのCraftsman 536,884,791ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Craftsmanの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Craftsman 536,884,791の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははCraftsman 536,884,791の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Craftsman 536,884,791に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Craftsman 536,884,791デバイスの基本機能を使うにあたってのヒント。 Craftsman 536,884,791のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Craftsman 536,884,791に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるCraftsman 536,884,791のメーカー/サービスへの連絡先に関する情報。

Craftsman 536,884,791についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもCraftsman 536,884,791の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがCraftsman 536,884,791で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)