Husqvarna 96193005301の取扱説明書

24ページ 1.38 mb
ダウンロード

ページに移動 of 24

Summary
  • Husqvarna 96193005301 - page 1

    12527HV OPERA TOR'S MANU AL ...

  • Husqvarna 96193005301 - page 2

    2 IMPORT ANT Safe Operation Practices for W alk-Behind Snow Throwers This snow thrower is capable of amputating hands and feet and throwing objects. F ailure to observe the following safety instructions could result in serious injury . WARNING: This snow thrower is for use on sidewalks, driveways and other ground level surfaces. Caution should be e ...

  • Husqvarna 96193005301 - page 3

    3 CONGRA TUL A TIONS on your purchase of a new snow thrower . It has been designed, engineered and man u - fac tured to give best possible dependability and per for - mance. Should you experience any problem you cannot easily remedy , please contact your nearest authorized service center . We have competent, well-trained tech ni cians and the prope ...

  • Husqvarna 96193005301 - page 4

    4 P ARTS P ACKED SEP ARA TEL Y IN CARTON (3) RET AINER SPRINGS (169675) (1) WASHER 3/8 (19131316) (1) L OCKNUT 3/8 (73800600) SAFTEY IGNITION KEY(S) (422663) (1) MUL TI- WRENCH (180684) (1) L OCKNUT 5/16-18 (751153) (1) CARRIAGE BOL T 5/16-18 x 5/8 (72250505) (1) L OCKNUT 1/4-20 (191730) (1) SHOULDER BOL T 1/4-20 (179829) (1) SPRING (184505) (1) PO ...

  • Husqvarna 96193005301 - page 5

    5 AS SEMBL Y / PRE-OPERA TION Read these instructions and this manual in its entirety before you attempt to assemble or operate your new snow thrower . Reading the entire manual will familiarize you with the unit, which will assist you in assembly , operation and maintenance of the product. Y our new snow thrower has been as sem bled at the factory ...

  • Husqvarna 96193005301 - page 6

    6 AS SEMBL Y / PRE-OPERA TION AUGER CONTROL LEVER AUGER CONTROL ROD AUGER CONTROL BRACKET RET AINER SPRING FIG. 6 TRACTION DRIVE CON TROL ROD DRIVE CONTROL BRACKET RET AINER SPRING TRACTION DRIVE CON TROL LEVER FIG. 4 INST ALL TRACTION DRIVE CONTROL ROD (See Figs. 3 and 4) The traction drive control rod is installed on the snow thrower . 1. Remove ...

  • Husqvarna 96193005301 - page 7

    7 AS SEMBL Y / PRE-OPERA TION INST ALL DISCHARGE CHUTE / CHUTE ROT A TOR HEAD (See Fig. 7) NOTE: The multi-wrench provided in your parts bag may be used to install the chute rotator head. 1. Place discharge chute assembly on top of chute base with discharge opening toward front of snow thrower . 2. Position chute rotator head over chute bracket. If ...

  • Husqvarna 96193005301 - page 8

    8 OPERA TION KNOW YOUR SNOW THROWER READ THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERA TING YOUR SNOW THROWER. Compare the illustrations with your snow thrower to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. These symbols may appear on your snow thrower or in literat ...

  • Husqvarna 96193005301 - page 9

    9 MEETS A.N.S.I. SAFETY REQUIREMENTS Our snow throwers conform to the standards of the American National Standards Institute. FIG. 10 OPERA TION Drive speed control lever - used to select forward or reverse motion and speed of snow thrower . T raction drive control lever - used to engage power -pro- pelled for ward or reverse motion of snow thrower ...

  • Husqvarna 96193005301 - page 10

    10 TO THROW SNOW (See Fig. 14) The auger rotation is controlled by the auger control lever located on the right side handle. • Squeeze auger control lever to handle to engage the auger and throw snow . • Release the auger control lever to stop throwing snow . OPERA TION TO CONTROL SNOW DISCHARGE (See Fig. 13) WARNING: Snow throwers have ex- pos ...

  • Husqvarna 96193005301 - page 11

    11 OPERA TION USING THE CLEAN-OUT TOOL (See Fig. 15) In certain snow conditions, the discharge chute may be- come clogged with ice and snow . Use the clean-out tool to dislodge this blockage. When cleaning, repairing, or in spect ing, make certain all controls are disengaged and the au- ger/impeller and all moving parts have stopped. Disconnect the ...

  • Husqvarna 96193005301 - page 12

    12 OPERA TION SKID PL A TE L OW POSITION (HIGH GROUND CLEAR ANCE) HEX NUTS HIGH POSITION (L OW GROUND CLEARANCE) AUGER HOUSING FIG. 18 SCRAPER BAR FIG. 19 PRIM ER SAFETY IG NI TION KEY ON / OFF SWITCH CHOKE CON- TROL ST ARTER BUTTON FUEL SHUT -OFF VAL VE NOTE: ALL ITEMS ARE SHOWN IN THEIR TYPICAL L OCA TION. ACTUAL L OCA TION MA Y V ARY WITH ENGINE ...

  • Husqvarna 96193005301 - page 13

    13 OPERA TION TO ST ART ENGINE • Be sure fuel shut-off valve is in the “OPEN” position. Y our snow thrower engine is equipped with both a 120 V olt A.C. electric starter and a recoil starter . The electric starter is equipped with a three-wire power cord and plug and is designed to operate on 120 V olt A .C. household current. • Be sure you ...

  • Husqvarna 96193005301 - page 14

    14 MAINTENANCE LUBRICA TION CHART GENERAL REC OM MEN DA TIONS The warranty on this snow thrower does not cover items that have been sub ject ed to operator abuse or negligence. T o receive full value from the warranty , operator must maintain snow thrower as in struct ed in this manual. Some ad just ments will need to be made periodically to proper ...

  • Husqvarna 96193005301 - page 15

    15 MAINTENANCE SNOW THROWER Always observe safety rules when performing main te nance. TIRES • Maintain proper air pressure in both tires (14–17 PSI). • Keep tires free of gasoline / oil, which can harm rubber . NOTE: T o seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer . ...

  • Husqvarna 96193005301 - page 16

    16 SERVICE AND ADJUSTMENTS BEL T COVER SCREWS FRAME FIG. 21 SHEAR BOL TS (See Fig. 20) AUGER SHEAR BOL TS Both right and left-hand augers are secured to the auger shaft with a shear bolt and hex nut. Should a foreign ob- ject or ice become lodged in the augers, the shear bolts are designed to break, preventing damage to any other com po nents. If o ...

  • Husqvarna 96193005301 - page 17

    17 SERVICE AND ADJUSTMENTS 8. RELIEVE TENSION ON TRACTION DRIVE BEL T IDLER and remove traction drive belt from around pulleys. HINT : Insert a 3/8" drive ratchet (in the “ON” position) into the square hole in idler arm and rotate ratchet clockwise to relieve tension. 9. With tension relieved on idler , install new traction drive belt arou ...

  • Husqvarna 96193005301 - page 18

    18 AXLE KLIK PIN (INST ALL IN OUTER HOLE OF AXLE ONL Y) OUTER HOLE WHEEL HUB WHEEL FIG. 23 SERVICE AND ADJUSTMENTS TO ADJUST CABLE TENSION (See Fig. 24) Adjust cable tension by turning the adjuster turn buckle, located on the right hand cable. Grasp the long section tightly and turn the short section to lengthen the adjuster . Adjust until cable is ...

  • Husqvarna 96193005301 - page 19

    19 STORAGE Immediately prepare your snow thrower for storage at the end of the season or if the unit will not be used for 30 days or more. WARNING: Never store the snow thrower with gaso line in the tank in side a build ing where fumes may reach an open flame, spark or pilot light as on a fur nace, water heater , clothes dryer or gas ap pli ance. A ...

  • Husqvarna 96193005301 - page 20

    20 TROUBLESHOOTING Does not start 1. Fuel shut-off valve (if so 1. T urn fuel shut-off valve to OPEN position. equipped) in OFF position. 2. Safety ignition key 2. Insert safety ignition key . is not inserted. 3. Out of fuel. 3. Fill fuel tank with fresh, clean gasoline. 4. Throttle in STOP position 4. Move throttle to FAST position (or ON/OFF swit ...

  • Husqvarna 96193005301 - page 21

    21 Consumer Wheeled Produc ts – Limited Warranty Husqvarna warrants to the original retail purchaser that this Husqvarna® product is free from defects in material or workmanshi p under normal use and maintenance from the date of retail purc hase for the applicable Warra nt y Period shown on Exhibit A . Certain components (e.g. , engines and tran ...

  • Husqvarna 96193005301 - page 22

    22 c. Preventative maintenance as outlin ed in the operator’s manual. In addition, you must cease using the product immediately upon any failure or damage. The product should be taken to a n authori zed Husqvarna servicing dealer prior to any further use. 4. Damages resulting from normal aging, wear and tear or neglect are NOT covered. The Li mit ...

  • Husqvarna 96193005301 - page 23

    23 Consumer Wheeled Warranty Chart 2010 Exhibit A Consumer (personal, household use only) Commercial (any commercial, professional, institutional, arigculutral, or income producing use, other than Rental Use) Rental (any rental usage) Riding Lawn Tractors: Frame, Chassis, Front Axle 5 Years NO W ARRANTY NO W ARRANTY Engine* * * * Transmission (if m ...

  • Husqvarna 96193005301 - page 24

    532 43 73-92 07.21.10 TH Printed in U.S.A. Consumer Wheeled Warranty Chart 2010 Exhibit A Consumer (personal, household use only) Commercial (any commercial, professional, institutional, arigculutral, or income producing use, other than Rental Use) Rental (any rental usage) Product/Component Front Mounted Deck Riders Engine* * * * Transmission 2 Ye ...

メーカー Husqvarna カテゴリー Snow Blower

Husqvarna 96193005301のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 96193005301の取扱説明書
- Husqvarnaの製品カード
- パンフレット
- またはHusqvarna 96193005301の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Husqvarna 96193005301の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Husqvarna 96193005301の取り付け説明書、サービスマニュアル、簡易説明書、またはHusqvarna 96193005301のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Husqvarna 96193005301の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Husqvarna 96193005301デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがHusqvarna 96193005301を使用するのを助ける技術的文書のことです。説明書は通常、全てのHusqvarna 96193005301ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Husqvarnaの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Husqvarna 96193005301の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははHusqvarna 96193005301の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Husqvarna 96193005301に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Husqvarna 96193005301デバイスの基本機能を使うにあたってのヒント。 Husqvarna 96193005301のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Husqvarna 96193005301に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるHusqvarna 96193005301のメーカー/サービスへの連絡先に関する情報。

Husqvarna 96193005301についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもHusqvarna 96193005301の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがHusqvarna 96193005301で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)