Knoll Systems HT200の取扱説明書

30ページ 0.97 mb
ダウンロード

ページに移動 of 30

Summary
  • Knoll Systems HT200 - page 1

    HT200 Users Manual v1.0 Complies with part 15 of the FCC rules. Operation is subject to: 1. This device may not cause harmful interference 2. This device must accept any interference received including interference that may cause undesired operation. WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER, NO USER SERVICEABLE PARTS I ...

  • Knoll Systems HT200 - page 2

    IMPORTANT SAFEGUARDS These safety instructions are to ensure the long life of your projector and to prevent fire and shock. Please read them carefully and heed all warnings. Installation • For best results, use your projector in a darkened room. • Place the projector on a flat, level surface in a dry area away from dust and moisture or hang it ...

  • Knoll Systems HT200 - page 3

    Table of Contents 2 IMPORTANT SAFETY INFORMATION 3 Table of contents 4 Basic information 5 Features 5 Remote control 6 Terminal connections 7 Projector part identification 8 Projector positioning 9 Connecting video equipment 10 Connecting component video 11 Connecting a PC or Macintosh 13 Using the remote control as a computer mouse 13 Wireless mou ...

  • Knoll Systems HT200 - page 4

    Basic HT200 Information Congratulations On Your Purchase of the HT200 Projector! The HT200 is one of the very best Projectors available today. The HT200 enables you to project precise images up to 300 inches across (measured diagonally) from your PC or Macintosh computer (desktop or notebook), VCR, document cam era, laser disc player, DVD player, e ...

  • Knoll Systems HT200 - page 5

    Remote Control Inserting the batteries 1) Press firmly and slide the battery cover off. 2) Insert the supplied two batteries (size AA/R6). Ensure that the polarities (+ and -_) of the batteries are aligned correctly. Always replace batteries with fresh alkaline type. 3) Slip the cover back over the batteries until it snaps into place. Notes • If ...

  • Knoll Systems HT200 - page 6

    Terminal Connection Panel Projector Part Identification 6 ...

  • Knoll Systems HT200 - page 7

    Installation The distance from the projector lens to the screen determines to the size of the projected image, therefore, you need to consider the place where you set up the projector and screen before making connections. You also need to consider the screen size and height of the unit and screen as other important factors. Tip: Although not advise ...

  • Knoll Systems HT200 - page 8

    Use the following information to position the projector. Horizontally the projector needs to be positions with the lens-centered left to right Projection Distance 4:3 Video Screen Distance to Screen 47" 83" 122" 165" 210" 415" 485" Screen Diag. (min.) 24" 40" 60" 80" 100" 200" 233&quo ...

  • Knoll Systems HT200 - page 9

    Connecting Video Equipment You can connect a document camera, VCR, laser disc player, and DVD player, etc. Connecting to the VIDEO IN VIDEO/S-VIDEO JACKS You can connect up to two pieces of video equipment to the VIDEO IN jacks following the illustration below. Two types of connections can be made. Connect either using the cables indicated in dotte ...

  • Knoll Systems HT200 - page 10

    Connecting Component Video Equipment withYCbCr output jacks to the RGB IN connector You can also connect the video component to the RGB IN connector, if the video component has the component video (YCbCr) signal jacks. This connection may provide a better picture quality than the connections on page 9. • You can switch the input source to VIDEO, ...

  • Knoll Systems HT200 - page 11

    Connecting a PC or Macintosh Connecting a PC or Macint osh to the Projector enables com puter images for im pressive presentati ons. • The following display standards are supported: VGA 640x480 for graphics VGA 640x400 for graphics VGA 640x350 for graphics VGA 720x400 for text CGA 720x350 for text SuperVGA 800x600 Macintosh at 640x480 Macintosh a ...

  • Knoll Systems HT200 - page 12

    Modifying the DIP switch (for Macintosh) setting Modify the DIP switch setting on the MAC cable as shown below. Macintosh adapter cable DIP switch setting (o=ON) MONITOR RESOLUTION 1 2 3 4 5 6 Multiple scan 21 o o o Multiple scan 21 o o o Multiple scan 21 o o o o VGA/SVGA o o 21 Color 1152x870 o o o o 19 Color 1024x768 o o 16 Color 832x624 o o 13 C ...

  • Knoll Systems HT200 - page 13

    Connecting the remote mouse receiver to an IBM PC/AT computer Connect the IBM/Mac connector on the remote mouse receiver and PC's mouse port with the supplied serial cable. Connecting the remote mouse receiver to an IBM PS/2 or Macintosh computer Connect the supplied serial cable to the IBM/ Mac connector on the remote mouse receiver. Connect ...

  • Knoll Systems HT200 - page 14

    2) Press the POWER ON button on the remote control or the POWER button on top of the unit to turn on the unit. The POWER indicator on top of the unit turns to green and start blinking. It will take one minute for the projector to be ready to use . Wait until the indicator stops blinking and lights steadily in green. Note: While the POWER indicator ...

  • Knoll Systems HT200 - page 15

    7) Change the unit setting to suit to the pr ojecting method and selected source as described in step 4. • Select the type of projection If the projected image is horizontally reversed or upside down, change the projection type. See page 19. • If the component video signal output jacks of the video component are connected to the RGB IN connecto ...

  • Knoll Systems HT200 - page 16

    Changing computer's video resolutions Depending on your computer's graphic capability, you may be able to select one of several resolutions. Generally a computer- either a PC or Macintosh- with 1 MB VRAM will run: 640 x 480 at 16.7 million colors (24 bit True color) 800 x 600 at 65,000 colors. 1024 x 768 at 256 colors. As the resolution i ...

  • Knoll Systems HT200 - page 17

    Adjusting the volume of the projector speaker Press VOLUME + to increase the volume or - to decrease. The volume can also be adjusted with the menu operation (see page 24). Using the laser pointer You can highlight the desired point on the screen with the beamed red light. ***Caution*** Do not look into the laser pointer while it is on. Do not poin ...

  • Knoll Systems HT200 - page 18

    Menu operation- Selecting the input source with the remote 1) Press MENU. The button lights in red and the main me nu appears on the screen. If you don't proceed to step 2 within ten seconds, the button goes off. Note: The menu will not be displayed if the picture is enlarged even slightly. In such a case, reduce the picture size to normal bef ...

  • Knoll Systems HT200 - page 19

    of the selected menu item. value of the selected menu item. Selecting the projection type; Floor, Ceiling, Rear and Front This reorients your image for your type of projection. 1. Press MENU to display the main menu. 2. Press the cursor up or down key to select "SETTING MENU." 3. Press L-CLICK to display the SETTING MENU. 4. Press the cur ...

  • Knoll Systems HT200 - page 20

    Setting "INPUT MODE" to "YCbCr" or Component Video When you have connected the component vide o (YCbCr) signal output jacks of the video component to the RGB IN connector on the unit (see page 10), set "IMAGE MODE" to "YCbCr" to obtain better picture quality. 1. Select the input source RGB (see page 13). 2. P ...

  • Knoll Systems HT200 - page 21

    Timing Chart Signal Resolution H. Sync. (kHz) V. Sync. (Hz) Dot Clock (MHz) 1 NTSC 640 x 480 15.734 59.94 - 2 PAL 768 x 576 15.625 50 - 3 SECAM 768 x 576 15.625 50 - 4 VESA 640 x 350 37.86 85.08 31.5 5 Mac 640 x 400 35 66 30.24 6 IBM 640 X 400 31.47 70 25.175 7 VESA 640 X 400 37.86 85.08 31.5 8 VESA 640 X 480 31.47 59.94 25.175 9 IBM 640 X 480 31.4 ...

  • Knoll Systems HT200 - page 22

    Adjusting the clock frequency (PICTURE ADJ) and clock phase (FINE PICTURE) manually When "AUTO PICTURE" is set to "ON," the cl ock frequency and clock phase will be adjusted automatically. However, if you need any manua l adjustment for these two item s, you first need to set "AUTO PICTURE" to "OFF" as indica ...

  • Knoll Systems HT200 - page 23

    Storing the most recent “PICTURE ADJ,” “FINE PICTURE,” “H POSITION,” AND “V POSITION” settings You can store the above present settings in the memory. CUSTOM 1 to 5. 1. Select the input source RGB (see page 13). 2. Press MENU to display the main menu. 3. Press the cursor up or down key to select “SETTING MENU.” 4. Press L-CLICK ...

  • Knoll Systems HT200 - page 24

    Adjusting the picture elements The picture elements such as brightness, contr ast, white balance, and so on can be adjusted individually for each input source. The adjustab le items vary depending on the input source and “INPUT MODE” setting (see page 20). Input source (The elements marked with “O” are adjustable.) VIDEO S-VIDEO RGB INPUT M ...

  • Knoll Systems HT200 - page 25

    The following three types of gamma modes can be selected according to your preferences: • NORMAL, • NATURAL 1, or • NATURAL 2. 8. Press L-CLICK. 9. Press the cursor up or down key to select “INP UT MODE,” then press the cursor +/- key to select the input mode. If the input source is RGB, refer to “Se tting INPUT MODE to YcbCr” on page ...

  • Knoll Systems HT200 - page 26

    Turning the projector off with on screen functions With the remote control: Press the POWER OFF button a for 2 seconds (the projector will turn off regardless of the “POWER OFF” setting) With the projector keypad: (When “DISPLAY” is set to “ON”) Press the POWER button. “POWER OFF/ENTER” appears. Press ENTER. The projector will turn ...

  • Knoll Systems HT200 - page 27

    Specifications Optical DMD TM Single Chip Digital Micro Device (DMD TM), 800x600 dots Lens Manual zoom, manual focus F3.0 f =27.5 to 35.75m m Lamp Metal halide lamp 280W Image Size 610 to 7620mm (24 to 300 inches) diagonal Projection Distance 1.2 to 12.3m Light Output 800 ANSI lumens (normally white) Contrast Ratio 500:1 Color Temperature 7000 Kelv ...

  • Knoll Systems HT200 - page 28

    Troubleshooting This section helps you resolve problems while setting up or using your projector. Common Problems & Solutions Problem Check These Items Does not turn on Check that the cord is plugged in and that the power switch on the back panel is on. (See page 13.) Check the status light to see if the projector has overheated or the lamp usa ...

  • Knoll Systems HT200 - page 29

    When the STATUS indicator on the projector keypad lights or blinks Status Light Message Condition Status OFF Normal On Continually The projector lamp has exceeded 1000 hours of operation and should be replaced. Blinking Very Rapidly (On and off in a cycle of 1 sec.) The lamp housing is not correctly installed. Install it correctly. Blinking Rapidly ...

  • Knoll Systems HT200 - page 30

    Lamp housing replacement procedure 1. Switch off the m ain power and unplug the power cord. 2. Wait at least one hour for the lam p to cool. 3. Turn the unit upside down carefully . 4. Loosen the lamp cover securing screw. 5. Slide the lamp cover in the direction of the arrow and remove it. CAUTION : Do not use a lamp housing other than the Knoll r ...

メーカー Knoll Systems カテゴリー Projector

Knoll Systems HT200のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- HT200の取扱説明書
- Knoll Systemsの製品カード
- パンフレット
- またはKnoll Systems HT200の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Knoll Systems HT200の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Knoll Systems HT200の取り付け説明書、サービスマニュアル、簡易説明書、またはKnoll Systems HT200のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Knoll Systems HT200の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Knoll Systems HT200デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがKnoll Systems HT200を使用するのを助ける技術的文書のことです。説明書は通常、全てのKnoll Systems HT200ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Knoll Systemsの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Knoll Systems HT200の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははKnoll Systems HT200の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Knoll Systems HT200に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Knoll Systems HT200デバイスの基本機能を使うにあたってのヒント。 Knoll Systems HT200のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Knoll Systems HT200に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるKnoll Systems HT200のメーカー/サービスへの連絡先に関する情報。

Knoll Systems HT200についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもKnoll Systems HT200の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがKnoll Systems HT200で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)