RIDGID R841150の取扱説明書

22ページ 1.18 mb
ダウンロード

ページに移動 of 22

Summary
  • RIDGID R841150 - page 1

    22 22 20 This new drill has been engineered and manufactured to our high standards for dependability, ease of operation, and operator safety. When properly cared for, the drill will give you years of rugged, trouble-free performance. WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual before using this p ...

  • RIDGID R841150 - page 2

    2 T ABLE OF CONTENTS ■ ■ ■ ■ ■ Introduction .................................................................................................................................................................... 2 ■ ■ ■ ■ ■ General Saf ety Rules ....................................................................................... ...

  • RIDGID R841150 - page 3

    3 GENERAL SAFETY RULES WARNING: Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. SA VE THESE INSTR UCTIONS WORK AREA ■ K eep your w ork area clean and well lit . Cluttered benches and dark areas invite accidents . ■ Do not operate power tool ...

  • RIDGID R841150 - page 4

    4 SER VICE ■ T ool service must be performed onl y b y qualified repair personnel. Service or maintenance perf or med by unqualified personnel ma y result in a risk of injur y . ■ When servicing a tool, use onl y identical replace- ment parts. Follo w instructions in the Maintenance section of this manual. Use of unauthor ized parts or f ailure ...

  • RIDGID R841150 - page 5

    5 WARNING: Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. ■ Never use a battery that has been dropped or received a sharp blow. A damaged battery is subject to explosion. Properly dispose of a dropped battery immediately. Failure to heed thi ...

  • RIDGID R841150 - page 6

    6 The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and the explanations with them, deserve your careful attention and understanding. The safety warnings do not by themselves eliminate any danger. The instructions or warnings they give are not substitutes for proper accident prevention measures. Sym ...

  • RIDGID R841150 - page 7

    7 SPECIFICA TIONS Chuck .......................................................................................................................... .................... 1/2 in. (13 mm) Keyless Motor .......................................................................................................................... ............................. ...

  • RIDGID R841150 - page 8

    8 Fig. 1 BIT ST ORAGE DIRECTION OF ROT A TION SELECTOR (FORW ARD / REVERSE / LOCK OFF [CENTER LOCK POSITION] ) TORQUE ADJUSTMENT RING FEA TURES KEYLESS CHUCK BA TTER Y P ACK DUAL PORT CHARGER 22 22 20 DEPTH GAGE ROD 30 min 30 min ? 4-1/8 in. ...

  • RIDGID R841150 - page 9

    9 UNP A CKING INSTRUCTIONS When unpacking the tool: ■ Carefully remov e the tool and accessories from the box. ■ Make sure that all items listed in the pac king list are in- cluded. ■ Inspect the tool carefully to make sure no breakage or damage occurred during shipping. ■ Do not discard the packing material until you ha v e care- fully ins ...

  • RIDGID R841150 - page 10

    10 WARNING: Do not allow familiarity with the hammer drill to make you careless. Remember that a careless frac- tion of a second is sufficient to inflict severe injury. CHARGING BATTERY PACK The battery pack for this tool has been shipped in a low charge condition to prevent possible problems. Therefore, you should charge it until the light on fron ...

  • RIDGID R841150 - page 11

    11 30 min 30 min ? OPERA TION LED B A TTER Y RED GREEN ACTION INDICA T OR P A C K LED LE D Power Without battery pack ON OFF Ready to charge battery pack Evaluate Hot battery pack Flashing OFF When battery pack reaches cooled temperature, charger begins fast charge mode Evaluate Cold battery pack Flashing OFF When battery pack reaches warmed temper ...

  • RIDGID R841150 - page 12

    12 Fig. 6 V ARIABLE SPEED SWITCH TRIGGER OPERA TION TO INSTALL BATTERY PACK ■ Lock the switch trigger on the drill by placing the direction of rotation (forward-reverse) selector in center position. See Figure 4. ■ Place batter y pac k in the drill. Align raised r ib on battery pack with the groove inside the drill. See Figure 5. ■ Make sure ...

  • RIDGID R841150 - page 13

    13 This drill has an electr ic br ake. When the trigger switch is released, the chuck stops turning. When the brak e is functioning properly , spar ks will be visib le through the v ent slots on the housing. This is normal and is the action of the bra ke . Note: You might hear a whistling or ringing noise from the switch during use. Do not be conce ...

  • RIDGID R841150 - page 14

    14 INSTALLING BITS See Figures 9 and 10. ■ Lock the switch trigger by placing the direction of rotation selector in center position. See Figure 4. ■ Open or close chuck jaws to a point where the opening is slightly larger than the bit size you intend to use. Also, raise the front of the drill slightly to keep the bit from falling out of the chu ...

  • RIDGID R841150 - page 15

    15 Fig. 13 TO DECREASE TORQUE TO INCREASE TORQUE ADJUSTING RING INSTALLING DEPTH GAGE ROD See Figures 11 and 12. A depth gage rod has been pack ed with y our hammer dr ill to assist you in controlling the depth of drilled holes. When drilling holes with the depth gage rod installed, the desired hole depth has been reached when the end of the rod co ...

  • RIDGID R841150 - page 16

    16 OPERA TION BIT STORAGE See Figure 14. When not in use, the bit provided with this drill can be placed in the storage area located on the rear of the drill. WARNING: Always wear eye protection marked to comply with ANSI Z87.1. Failure to do so could result in dust, shavings, or loose particles being thrown into your eyes, resulting in possible se ...

  • RIDGID R841150 - page 17

    17 TO ADJUST DRILLING OR HAMMER MODE See Figure 16. T o adjust hammer drill to dr illing or hammer oper ation, rotate mode selector in the direction of arrows as shown in Figure 16. For your con v enience a hammer symbol and drill bit sym- bol hav e been molded into the selector . WARNING: Your hammer drill has not been designed for re- verse hamme ...

  • RIDGID R841150 - page 18

    18 Fig. 18 Fig. 19 Fig. 17 MAINTENANCE WARNING: When servicing use only identical RIDGID ® replace- ment parts. Use of any other parts may create a hazard or cause product damage. GENERAL A v oid using solvents when cleaning plastic parts. Most plas- tics are susceptible to damage from v arious types of com- mercial solv ents and may be damaged b ...

  • RIDGID R841150 - page 19

    19 R E C Y C L E 1 . 8 0 0 . 8 2 2 . 8 8 3 7 RBRC Ni Cd ™ MAINTENANCE To obtain the longest possible battery life, we suggest the following: ■ Store and charge your batteries in a cool area. Temperatures below 50°F or above 100°F will shorten battery life. ■ Never store batteries in a discharged condition. Recharge them immediately after th ...

  • RIDGID R841150 - page 20

    20 This product is manufactured under license from Ridgid, Inc. by One World Technologies, Inc. All warranty communications should be directed to One World Technologies, Inc. at (toll-free) 1-866-539-1710. 90-DAY SATISFACTION GUARANTEE POLICY During the first 90 days after the date of purchase , if you are dissatisfied with the perf ormance of this ...

  • RIDGID R841150 - page 21

    21 NO TES ...

  • RIDGID R841150 - page 22

    ® OPERA T OR’S MANU AL 18 V olt 1/2 in. (13 mm) Hammer Drill R841150 T wo Speed/Re versible Customer Service Information: F or par ts or ser vice, contact y our nearest RIDGID authorized ser vice center . Be sure to pro vide all relev ant inf ormation when you call or visit. For the location of the authorized service center nearest you, please c ...

メーカー RIDGID カテゴリー Drill

RIDGID R841150のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- R841150の取扱説明書
- RIDGIDの製品カード
- パンフレット
- またはRIDGID R841150の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、RIDGID R841150の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、RIDGID R841150の取り付け説明書、サービスマニュアル、簡易説明書、またはRIDGID R841150のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、RIDGID R841150の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

RIDGID R841150デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがRIDGID R841150を使用するのを助ける技術的文書のことです。説明書は通常、全てのRIDGID R841150ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

RIDGIDの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. RIDGID R841150の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははRIDGID R841150の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。RIDGID R841150に関してこのドキュメントで見つけることができる全てのヒントの目次
3. RIDGID R841150デバイスの基本機能を使うにあたってのヒント。 RIDGID R841150のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。RIDGID R841150に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるRIDGID R841150のメーカー/サービスへの連絡先に関する情報。

RIDGID R841150についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもRIDGID R841150の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがRIDGID R841150で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)