日本語 dropdown-ico

Bunn S/N 0005473 & UPの取扱説明書

32ページ 0.49 mb
ダウンロード

ページに移動 of 32

Summary
  • Bunn S/N 0005473 & UP - page 1

    JDF-4 S/N 0005473 & UP ! W A RN I N G DO NOT OV E RLOAD CIRCUI T. ALWAYS ELECTR ICALLY GRO U ND THE CHA SSIS OR ADAPTO R PLUG. DO NOT DE FORM PLU G O R CORD. FOLLOW NA TIONAL AND L OCAL ELECTR ICAL CO DES. KEEP C OMB USTIBLES A WAY. FAILUR E TO CO M PLY RISK S E QU IPME NT DAM AG E, F IR E O R SH OC K HAZAR D. READ T HE E NTI R E OP ERA TIN G M ...

  • Bunn S/N 0005473 & UP - page 2

    2 38218.1 020608 BUNN-O-MA TIC COMMERCIAL PRODUCT WARRANTY Bunn-O-Matic Corp. (“BUNN”) warrants equipment manufactured by it as follows: 1) All equipment other than as specified below: 2 years parts and 1 year labor . 2) Electronic circuit and/or control boards: parts and labor for 3 years. 3) Compressors on refrigeration equipment: 5 years pa ...

  • Bunn S/N 0005473 & UP - page 3

    3 USER NOTICES Carefully read and follow all notices on the equipment and in this manual. They were written for your protec- tion. All notices are to be kept in good condition. Replace any unreadable or damaged labels. 27442.0000 00986.0002 33461.0000 CHARGE T ype R134A, Amount 10 oz (283 gm) Design Pressures: High 335 psi (23 bar) (2.31 MPa) Low 8 ...

  • Bunn S/N 0005473 & UP - page 4

    4 INITIAL SET -UP CAUTION: The dispenser is very heavy! Use care when lifting or moving it. Use at least two people to lift or move the dispenser . Place the dispenser on a sturdy counter or shelf able to support at least 230 lbs. (104.3 kg). The JDF-4 is designed for indoor use only . Set the dispenser on the counter where it will be used. The JDF ...

  • Bunn S/N 0005473 & UP - page 5

    5 PLUMBING REQUIREMENTS This dispenser must be connected to a COLD WA TER system with operating pressure between 20 and 100 psi (138 and 690 kPa). This water source must be capable of producing a minimum flow rate of 3 fluid ounces (88.7 milliliters) per second. A shut off valve should be installed in the line before the dispenser . Install a reg ...

  • Bunn S/N 0005473 & UP - page 6

    6 OPERA TING CONTROLS FIG 2 Refrigeration Switch FIG 3 Sanitize Switch & Water V alves A. Sanitize Switch B. Water Bath V alve C. Main Water V alve (Early Models) C P2262.60 P2479 A B Refrigeration Switch The refrigeration switch is located on the top of the dispenser near the left rear corner . This switch controls power to the compressor and ...

  • Bunn S/N 0005473 & UP - page 7

    7 OPERA TING CONTROLS (cont.) FIG 4 Press and Hold Models A. Product Dispense Switch Pressing and holding switch will initiate product flow from the respective nozzle; releasing the switch will stop the flow . B. Chilled Water Dispense Switch Pressing and holding switch will initiate chilled water flow from the nozzle; releasing the switch will ...

  • Bunn S/N 0005473 & UP - page 8

    8 INITIAL FILL CAUTION: The dispenser must be disconnected from the power source throughout the initial fill except when specified in the instructions. 1. Remove drip tray assembly and splash panel from the dispenser . Set the drip tray back into place. 2. Ensure that the Main Water Valve (Early models) and the W ater Bath V alve Fig 3, are turne ...

  • Bunn S/N 0005473 & UP - page 9

    9 INITIAL FILL (cont) Ambient Concentrates (Optional) 1. Install an Ambient Concentrate Conversion Kit (BUNN-O-MA TIC part number 33699.0000) per the instruc- tions provided in the kit. 2. Attach the concentrate product hose to the appropriate concentrate line located behind the dispenser’ s splash panel. 3. Attach the other end of the product ho ...

  • Bunn S/N 0005473 & UP - page 10

    10 CLEANING & PREVENTIVE MAINTENANCE General Cleaning and Sanitizing Procedures Note: The Bunn Juice Dispenser incorporates a rinse reminder feature which lights the rinse led on the front panel when it is time to rinse. See dip switch function list to activate this feature. Daily: Rinse Procedure T ools required: 32 oz. (946 ml) minimum empty ...

  • Bunn S/N 0005473 & UP - page 11

    11 CLEANING (cont) 6. Select the dispense stations by pressing the “Dispense Switch” for that station. Use the “+/Stop Switch” for portion contol dispensers. The “REFILL” indicator will light and the beeper will sound for the dispense head selected. 7. Once the dispense heads have been selected, press and hold the “Sanitize Switch” ...

  • Bunn S/N 0005473 & UP - page 12

    12 Monthly: Clean Condenser Air Filter 1. Remove the condenser air filter located on the rear of the dispenser . 2. Using a water spray , clean the air filter . Annually: Replace Pump T ubing CLEANING (cont) 38218.1 012207 NOTE: High volume applications may require tubing changes every 6 months. 1. Open dispenser door . 2. Remove all product cont ...

  • Bunn S/N 0005473 & UP - page 13

    13 ADJUSTMENT & OPTIONAL SETTINGS T otal Dispense Ratio Set Up Procedure 1. Adjust water flow as described in W ater Flow T esting and Adjustment . Record water output setting for later reference on each dispense head. 2. Enter program mode by simultaneously pressing both hidden switches. 3. Press and hold the dispense button, you will hear 5 ...

  • Bunn S/N 0005473 & UP - page 14

    14 4. At the end of the 5 second period, the selected position will dispense water (no concentrate) for only 3 sec- onds. 5. Measure the water dispensed. 6. Adjust the water flow rate Fig 7, (clockwise to increase flow rate; counterclockwise to decrease flow rate) to the corresponding product mix ratio as follows: 7. Repeat steps 3 through 6 as ...

  • Bunn S/N 0005473 & UP - page 15

    15 3. T o decrease the pump speed, press and hold the left-hand “Hidden Switch” (half-filled cir cle) and then mo- mentarily press the “Product Dispense Switch (“+/STOP Switch” for portion control dispensers). Each time the “Product Dispense” (“+/STOP”) Switch is pressed, the motor speed is decreased by one step (5 RPM.) Note tha ...

  • Bunn S/N 0005473 & UP - page 16

    16 1. Enter the “Pump Speed Programming” mode by simultaneously pressing both “Hidden Switches”. Note that the beeper sounds twice and that the “PROGRAM” indicator begins flashing. 2. Enter a “Lockout” password as follows: a) Press and hold the left hand “Hidden Switch” (half filled cir cle) for mode #1, the right hand “Hidd ...

  • Bunn S/N 0005473 & UP - page 17

    17 ADJUSTMENT & OPTIONAL SETTINGS (cont) Password Protection The programming modes and service lockout function may be password protected to prevent accidental or unauthorized access to these features. The dispenser is shipped from the factory with a password of “0” (no password.) 1. Enter the “Pump Speed Programming” mode by simultaneo ...

  • Bunn S/N 0005473 & UP - page 18

    18 Dispense Fault List “REFILL” indicator Beeper Fault 2 flashes 2 beeps Dispense station locked out. 3 flashes 3 beeps DISPENSE/RINSE sensing fault. 4 flashes 4 beeps DISPENSE/RINSE knob mis-positioned. 5 flashes 5 beeps Pump motor stalled/speed sensor inoperative. All “REFILL” 3 beeps Dispenser locked out. indicators flash 3 times Co ...

  • Bunn S/N 0005473 & UP - page 19

    19 Dip Switch Function List Dip Switch Controls Off On 1 “REFILL” indicator when “concentrate out” is detected. Inactive Active 2 Lockout dispense components when “concentrate out” is detected. Inactive Active ( Note ) 3 Number of positions that can dispense/rinse simultaneously . 3 2 4 Rinse timer Off On 5 Audio feedback during dispens ...

  • Bunn S/N 0005473 & UP - page 20

    20 Function # 0 1 2 3 4 101 102 103 104 7 8 9 10 11 12 13 14 15 16 17 18 27 28 29 30 31 32 33 34 50 51 52 53 54 55 75 76 77 78 99 100 Description Enter Password Set Pump 1 RPM (Concentrate A) Set Pump 2 RPM (Concentrate A) Set Pump 3 RPM (Concentrate A) Set Pump 4 RPM (Concentrate A) Set Pump 1 RPM (Concentrate B) Set Pump 2 RPM (Concentrate B) Set ...

  • Bunn S/N 0005473 & UP - page 21

    21 TROUBLESHOOTING A troubleshooting guide is provided to suggest probable causes and remedies for the most likely problems encountered. If the problem remains after exhausting the troubleshooting steps, contact the Bunn-O-Matic T echnical Ser vice Department. • Inspection, testing, and repair of electrical equipment should be per formed only by ...

  • Bunn S/N 0005473 & UP - page 22

    22 TROUBLESHOOTING (cont.) Check for "ON" position or no con- tinuity - replace switch. Clean or replace condenser filter . Replace fan motor or check fan blades for obstructions. Check compressor relay coil for 120vac. NOTE: Always check power with coil attached. If no 120vac - replace board. If yes, 120vac - replace relay . Note: Relay ...

  • Bunn S/N 0005473 & UP - page 23

    23 TROUBLESHOOTING (cont.) Dispense station not working "refill" LED and beep code. A) 3-Beep - Dispense/Rinse sens- ing fault. B) 4-Beep - Dispense/Rinse knob mis-positioned. Refill LED not extinguishing All stations dispense concentrate only 1. Bottle adapter switch mem - brane A) Dispense/Rinse switch mem - brane shorted out simultan ...

  • Bunn S/N 0005473 & UP - page 24

    24 TROUBLESHOOTING (cont.) Dispense station concentrate only Dispense station water only Dispense starts then stops or "refill" flashes and beeps 5 times. Replace solenoid (24vdc) or check wire connection between water valve and main control board. Rotate knob to dispense position. Check for variable dc voltage when corresponding dispen ...

  • Bunn S/N 0005473 & UP - page 25

    25 TROUBLESHOOTING (cont.) Water leak filling drip tray or around dispense deck area Water leaking beneath machine Erratic spray during dispense Dispense nozzle dripping water Can't access programming 1. Initial fill/setup 2. Dispense deck 3. Water pressure greater than 100psi 1. Bath tank overflow . 2. Condensation from cabinet cool- ing c ...

  • Bunn S/N 0005473 & UP - page 26

    26 TROUBLESHOOTING (cont.) Unit is not working and no beep/light fault codes Difficulty brixing and/or weak bev- erage 1. Step-down transformer . 2. Main control board. 1. Product viscosity or too cold. 2. Low water pressure. 3. High water pressure. 4. Dispense valve adjustment set- ting. 5. Brix ratio. Check for 120/24 vac. If no 24vac reading, r ...

  • Bunn S/N 0005473 & UP - page 27

    27 Difficulty brixing and/or weak bev- erage Difficulty brixing bag-in-box 1. Pump tubing. 2. Bottle adapter assembly leaking NOTE: Leaking water into con- centrate bottle during rinse of any station. 3. Use of portable water pump. Vacuum leak Inspect, clean, or replace tubing and pump rotor/rollers for ease of rotation. Replace bottle adapter as ...

  • Bunn S/N 0005473 & UP - page 28

    28 COOLANT SCHEMA TIC DIAGRAM CONDENSER SUCTION ACCUMULA TO R COMPRESSOR EV APORA TO R PROCESS TUBE FIL TER DRYER 38218.1 030306 ...

  • Bunn S/N 0005473 & UP - page 29

    29 J3-1 J3-2 J1-1 J1-5 J1-10 C O N T R O L P C B O A R D J1-18 J7-1 J7-5 J7-10 J7-16 J8-1 J8-8 J6-1 J6-6 J6-12 RIGHT LAMP ASSY . LEFT LAMP ASSY . GRN GRN GRN BLU BRN/BLK RED/BLK RED/BLK GRY WHI BLK LIMIT THERMOST AT K2 K2 COM P. COMPRESSOR ASSEMB LY + – RECT TRANSFORMER WHI/BLU WHI WHI WHI WHI/RED WHI/RED BLK BLU BLU RED/BLK RED/BLK GRY WH I WH I ...

  • Bunn S/N 0005473 & UP - page 30

    30 J3-1 J3-2 J1-1 J1-5 J1-10 C O N T R O L P C B O A R D J1-18 J7-1 J7-5 J7-10 J7-16 J8-1 J8-8 J6-1 J6-6 J6-12 SOL SOL #4 DISPENSE SOL ICE WA TER DISPENSE TA N RED/BLK RED/BLK RED/BLK WHI/YEL WHI/BLU SOL #2 DISPENSE #3 DISPENSE RED/BLK WHI/ORN SOL #1 DISPENSE #4 RINSE & DISPENSE LIMIT #2 RINSE & DISPENSE LIMIT #3 RINSE & DISPENSE LIMIT ...

  • Bunn S/N 0005473 & UP - page 31

    31 J3-1 J3-2 J1-1 J1-5 J1-10 C O N T R O L P C B O A R D J1-18 J7-1 J7-5 J7-10 J7-16 J8-1 J8-8 J6-1 J6-6 J6-12 J5-1 J5-5 J5-10 J5-15 J5-19 J4-1 J4-5 J4-10 J4-14 J9-1 J9-6 RED WHI GRN/WHI GRN/BLK ORN/BLK WHI/BLK BLU/WHI BLK/WHI RED/BLK RED/WHI ORN GRN BLU BLU/BLK BLK RED WHI GRN/WHI GRN/BLK ORN/BLK WHI/BLK BLU/WHI BLK/WHI RED/BLK RED/WHI ORN GRN BLU ...

  • Bunn S/N 0005473 & UP - page 32

    32 J3-1 J3-2 J1-1 J1-5 J1-10 C O N T R O L P C B O A R D J1-18 J7-1 J7-5 J7-10 J7-16 J8-1 J8-8 J6-1 J6-6 J6-12 RIGHT LAMP ASSY . LEFT LAMP ASSY . GRN 120V MODELS GRN GRN N AB AB AB L1 BLU BRN/BLK RED/BLK RED/BLK RED/BLK GRY WHI BLK LIMIT THERMOST AT K2 K2 COMP . COMPRESSOR ASSEMB LY + – RECT TRANSFORMER WHI/BLU WHI WHI WHI WHI/RED WHI/RED BLK BLU ...

メーカー Bunn カテゴリー Coffeemaker

Bunn S/N 0005473 & UPのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- S/N 0005473 & UPの取扱説明書
- Bunnの製品カード
- パンフレット
- またはBunn S/N 0005473 & UPの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Bunn S/N 0005473 & UPの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Bunn S/N 0005473 & UPの取り付け説明書、サービスマニュアル、簡易説明書、またはBunn S/N 0005473 & UPのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Bunn S/N 0005473 & UPの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Bunn S/N 0005473 & UPデバイスの取扱説明書はどのようなものですか？
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがBunn S/N 0005473 & UPを使用するのを助ける技術的文書のことです。説明書は通常、全てのBunn S/N 0005473 & UPユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Bunnの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Bunn S/N 0005473 & UPの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははBunn S/N 0005473 & UPの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Bunn S/N 0005473 & UPに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Bunn S/N 0005473 & UPデバイスの基本機能を使うにあたってのヒント。 Bunn S/N 0005473 & UPのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Bunn S/N 0005473 & UPに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるBunn S/N 0005473 & UPのメーカー/サービスへの連絡先に関する情報。

Bunn S/N 0005473 & UPについてご質問がありますか？

次のフォームを使用してください

見つけた説明書を読んでもBunn S/N 0005473 & UPの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがBunn S/N 0005473 & UPで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

Captcha
新しい画像

コメント (0)