AEG 34942Gの取扱説明書

26ページ 0.13 mb
ダウンロード

ページに移動 of 26

Summary
  • AEG 34942G - page 1

    AUS ERFAHRUNG GUT 34942G/35940G/3594 1G/35944G Gas hob T able de cuisson K ochmulde Gaskookplaat Piano di cottur a Oper ating and Installation Instructions GB Notice d’utilisation et d’encastr ement FR/BE Gebr auchs- und Einbauanweisung BE Gebruiksaanwijzing en Installatievoor schrift NL/BE Istruzioni per l’uso e l’installazione IT ...

  • AEG 34942G - page 2

    2 Important Safety Information Y ou MUST r ead these warning s car efully before in stalling or u sing the hob. If you need ass i stance, contact our Cu stomer Care Department on 087 05 350 350 In stallation ● This hob must be installed by qualified personnel, accor ding to the manufacturer’ s instructions and to the relevant British Standar ds ...

  • AEG 34942G - page 3

    3 ● When in use a gas cooking hob will produce heat and moistur e in the room in which it has been installed. Ensur e there is a continuous air supply , keeping air vents in good condition or installing a cooker hood with a venting hose. ● When using the hob for a long period of time, the ventilation should be impr oved, by opening a window or ...

  • AEG 34942G - page 4

    4 Content s Important Safety Information .................................................................... 2 In structions for the U ser .............................................................................. 6 Description of the Hob ........................................................................................... 6 Oper ation . ...

  • AEG 34942G - page 5

    5 This appliance is manufactured accor ding to the following EEC dir ectives: 73/23 EEC - 90/683 EEC - 93/68 EEC - 89/336 EEC - 90/396 EEC, current edition. Guide to U se the instruction s The following symbols will be found in the text to guide you thr oughout the Instructions: Safety Instructions Step by step instructions for an operation Hints a ...

  • AEG 34942G - page 6

    6 1. Hob T op 2. Rapid Burner 3. Semi-rapid Burner s 4. Double-cr own Burner 5. Auxiliary Burner 6. Contr ol knob for back left burner (semi-rapid) 7. Contr ol knob for back right burner (semi-rapid) 8. Contr ol knob for ront right burner (auxiliary) 9. Contr ol knob for central burner (double-crown) 1 0. Contr ol knob for front right burner (rapid ...

  • AEG 34942G - page 7

    7 HOB BURNERS To light a burner , turn the relevant contr ol knob anticlockwise to the maximum position ( ), then push it down to ignite the burner . Upon, ignition, adjust the flame as requir ed. If the burner does not ignite, turn the contr ol knob to zero, and try again. When switching on the mains, after installation or a power cut, it is quite ...

  • AEG 34942G - page 8

    8 Before any maintenance or cleaning can be carried out, you must DISCONNECT the hob fr om the electricity supply . The hob is best cleaned whilst it is still warm, as spillage can be removed mor e easily than if it is left to cool. The Hob T op Regularly wipe over the hob top using a soft cloth well wrung out in warm water to which a little washin ...

  • AEG 34942G - page 9

    9 Something Not W orking? If the hob is not working correctly , please carry out the following checks before contacting your local AEG Service For ce Centre. SYMPTOM ■ There is no spark when lighting the gas ■ The gas ring burns unevenly SOLUTION ◆ Check that the unit is plugged in and the electrical supply is switched on ◆ Check that the R ...

  • AEG 34942G - page 10

    10 Service and Spar e P art s When you contact the Service Centr e, they will need the following information: 1. Y our name, address and post code. 2. Y our telephone number 3. Clear and concise details of the fault 4. The model and the serial number (see r ating label on the back of this instruction booklet) 5. Date of pur chase If you r equire sp ...

  • AEG 34942G - page 11

    11 Guar antee Conditions AEG offer the following guar antee to the first pur chaser of this appliance. 1. The guarantee is valid for 12 months commencing when the appliance is handed over to the first r etail purchaser , which must be verified by purchase invoice or similar documentation. The guarantee does not cover commer cial use. 2. The guarant ...

  • AEG 34942G - page 12

    12 OVERALL DIMENSIONS Width: 860 mm. Depth: 500 mm. Height: 88 mm. W eight: 8 Kg. CUT OUT DIMENSIONS Width: 830 mm. Depth: 47 0 mm. Thickness: 30 mm. SUPPL Y CONNECTIONS Gas: RC 1/2 inch (1/2 inch male) Rear right hand corner Electric: 230-240V 50Hz supply , 3 cor e flexible cable with non rewir eable plug fitted with a 3 amp cartridge fuse. IGNITI ...

  • AEG 34942G - page 13

    13 Burner Dia. Tap By-pass Tap colour 1/100 mm Auxiliary 28 Red/Red Semi-rapid 32 Blue/Blue Rapid 40 Black/Black Double-Crown 56 Black/Red Aeration adjustment none BURNER RAPID SEMI-RAPID AUXILIARY DOUBLE (large) (medium) (small) CROWN POSITION MAX MIN MAX MIN MAX MIN MAX MIN NOMINAL THERMAL POWER kW 3.0 0.65 2.0 0.45 1.0 0.33 3.5 1.2 NOMINAL FLOW ...

  • AEG 34942G - page 14

    14 Important s afety requir ement s This hob must be installed in accor dance with the Gas Safety (Installation and Use) Regulations (Curr ent Edition) and the IEE Wiring Regulations (Curr ent Edition). Detailed r ecommendations are contained in the following British Standards Codes Of Pr actice: B.S. 6 172/ B.S. 5440, P ar . 2 and B.S. 689 1 Curr ...

  • AEG 34942G - page 15

    15 CLEARANCES REQUIRED WHEN FITTING THE GAS HOB WITHOUT A COOKER HOOD ABOVE CLEARANCES REQUIRED WHEN FITTING THE GAS HOB WITH A COOKER HOOD ABOVE In stallation IMPORTANT This hob must be installed by qualified personnel to the relevant British Standards. Any gas installation must be carried out by a CORGI r egistered installer . The manufacturer wi ...

  • AEG 34942G - page 16

    16 A) End of shaft with nut B) Washer C) Elbow FO 0814 FO 0264 this book be ignored. On the end of the shaft, which includes the GJ 1/2" thr eaded elbow , adjustment is fixed so that the washer is fitted between the components as shown in the diagr am. Screw the parts together without using excessive force. It is important to install the elbow ...

  • AEG 34942G - page 17

    17 830 470 55 min. 860 500 FO 2407 Cut Out Size The dimensions of the cut-out are given in the diagr am. Building In Building over a cupboar d or drawer If the hob is to be installed above a cupboar d or drawer it will be necessary to fit a heat resistant boar d below the base of the hob on the underside of the work surface. It is also recommended ...

  • AEG 34942G - page 18

    18 ON/OFF SWITCH FLEX OUTLET ON/OFF SWITCH FLEX OUTLET FO 0763 FO 0764 1 2 Building over a kitchen unit with door Proper arr angements must be taken in designing the furniture unit, in or der to avoid any contact with the bottom of the hob which can be heated when it is oper ated. The recommended solution is shown in diagram 3. The panel fitted und ...

  • AEG 34942G - page 19

    19 Building in Fitting the hob to the worktop Before fitting the hob into the cut out, a sealing gasket supplied with the hob must be fitted to the edge of the cut out. It is essential that no gaps are left in this seal in or der to prevent spillage near the hob seeping into the cabinet below . 1) Place the sealing gasket all ar ound the edge of th ...

  • AEG 34942G - page 20

    20 Electrical connection s Any electrical work r equired to install this hob should be carried out by a qualified electrician or competent person, in accor dance with the current r egulations. THIS HOB MUST BE EARTHED. The manufacturer declines any liability should these safety measur es not be observed. This hob is designed to be connected to a 23 ...

  • AEG 34942G - page 21

    21 P ermanent Connection In the case of a permanent connection, it is necessary that you install a double pole switch between the hob and the electricity supply (mains), with a minimum gap of 3 mm. between the switch contacts and of a type suitable for the r equired load in compliance with the current electric r egulations. The switch must not brea ...

  • AEG 34942G - page 22

    22 Fault Finding Pr eliminary Electrical System s Check START Isolate appliance and carry out: A: Earth Continuity check. Has inlet fuse blown? Carry out: C: Polarity check. Electricity supply should now be satisfactory. Carry out: D: Resistance to Earth check. Inlet wiring faulty. Rectify any fault. Isolate appliance and carry out: B: Insulation c ...

  • AEG 34942G - page 23

    23 A. EARTH CONTINUITY CHECK Appliance must be electrically disconnected - meter set on Ω (Ohms) x 1 scale and adjust zero if necessary . — Test leads fr om any appliance earth point to earth pin on plug. Resistance should be less than 0.1 Ω (Ohm), check all earth wir es for continuity and all contacts ar e clean and tight. B. INSULA TION CHE ...

  • AEG 34942G - page 24

    24 Check gas supply at burner Ignition Sy stem / Gas Ignition YES Check plug top fuse and replace if necessary Check polarity and earth continuity of supply point Check earth continuity of appliance Ignitor does not spark Check fitting of burners Check position of the electrode Check by pass simmer adjusted Light burner manually Check continuity fr ...

  • AEG 34942G - page 25

    25 Commi ssioning When the hob has been fully installed it will be necessary to check the minimum flame setting. T o do this, follow the procedur e below . 1) Turn the gas tap to the MAX position and ignite. 2) Set the gas tap to the MIN flame position then turn the contr ol knob fr om MIN to MAX several times. If the flame is unstable or is exting ...

  • AEG 34942G - page 26

    26 Conver sion fr om Natur al Gas to LPG It is important to note that this model is designed for use with natur al gas but can be converted for use with butane or pr opane gas providing the corr ect injectors ar e fitted and the gas rate is adjusted to suit. Method 1) Ensure that the gas taps ar e in the 'OFF' position 2) Isolate the hob ...

メーカー AEG カテゴリー Cooktop

AEG 34942Gのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 34942Gの取扱説明書
- AEGの製品カード
- パンフレット
- またはAEG 34942Gの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、AEG 34942Gの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、AEG 34942Gの取り付け説明書、サービスマニュアル、簡易説明書、またはAEG 34942Gのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、AEG 34942Gの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

AEG 34942Gデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがAEG 34942Gを使用するのを助ける技術的文書のことです。説明書は通常、全てのAEG 34942Gユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

AEGの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. AEG 34942Gの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははAEG 34942Gの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。AEG 34942Gに関してこのドキュメントで見つけることができる全てのヒントの目次
3. AEG 34942Gデバイスの基本機能を使うにあたってのヒント。 AEG 34942Gのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。AEG 34942Gに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるAEG 34942Gのメーカー/サービスへの連絡先に関する情報。

AEG 34942Gについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもAEG 34942Gの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがAEG 34942Gで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)