日本語 dropdown-ico

Therma-Tru Hinged Patio Door System Single Panel Assembly Unitの取扱説明書

16ページ 1.29 mb
ダウンロード

ページに移動 of 16

Summary
  • Therma-Tru Hinged Patio Door System Single Panel Assembly Unit - page 1

    P A TIO DOOR S YSTEMS ® Therma-T ru Hinged Patio Door System Single Panel Unit Assembly Read all instructions before starting. The applicable standards for these products are governed by the International Residential Code. Copies of performance ratings and testing are available on our website www.thermatru.com and our product manual. ...

  • Therma-Tru Hinged Patio Door System Single Panel Assembly Unit - page 2

    Part identification Inswing sill Outswing Sill Door Bottom - Inswing Door Bottom - Outswing Standard Hinge Adjustable Hinge Head Jamb Lock Jamb Hinge Jamb Head & Lock Weatherstrip Door Panel Hinge Weatherstrip Multi-point Lock Strikes Standard S trike Inswing Inswing Flange Outswing Flange Not all parts shown will be included in package. Parts ...

  • Therma-Tru Hinged Patio Door System Single Panel Assembly Unit - page 3

    Part identification - continued T ools/materials required #10 x 3/4” flat head screw #8 x 1-1/4” flat head screw #8 x 3/4” wafer head screw #10 x 2-1/2” flat head screw #8 x 2” flat head screw #6 x 3/4” flat head screw #8 x 3/4” flat head screw This is a listing of tools that may be required to assemble unit. • Drill/screw gun • P ...

  • Therma-Tru Hinged Patio Door System Single Panel Assembly Unit - page 4

    1 2 REMO VE COMPONENTS FROM P ACKA GING A TT ACH HINGES T O DOOR NOTE: Product that is purchased with the multi-point lock system will have additional instructions in the handle hardware box. Installation instructions will be included in the site package. NOTE: A large work area is needed to assemble the frame kit. Cover area with cardboard from on ...

  • Therma-Tru Hinged Patio Door System Single Panel Assembly Unit - page 5

    2 3 A TT ACH HINGES T O DOOR - continued INST ALL DOOR BOTT OM Adjustable Hinge Option #8 x 1-1/4” Attach hinge to door Locate the “H” and “V” markings on hinges. The two “H” hinges go in top and bottom locations with the “V” hinge in the center. For 8’, the “V” hinge is located second from top of door. Insert thick side of ...

  • Therma-Tru Hinged Patio Door System Single Panel Assembly Unit - page 6

    INST ALL WEA THERSTRIP Apply Weatherstrip to Active Frame Parts Press in kerf with hand. Trim Bottom End T rim weatherstrip as shown. Lock Jambs Hinge Jambs Head Jambs Align starting end with Align starting end with Align starting end with head gain. head gain. head gain. Fit and secure in place Fit and secure in place Fit and secure in place along ...

  • Therma-Tru Hinged Patio Door System Single Panel Assembly Unit - page 7

    INST ALL STRIKES 5 Fasten Security Strike Assembly to Lock Jamb Fasten with (2) #9 x 3/4" flat head screws or (2) 16 gauge 1/2" x 7/16" crown staples (not supplied) through strike plate on back side of jamb. NOTE: Do not staple through screw holes when using staples in place of screws. Fasten Strike Plates to Lock Jamb Fit strike pla ...

  • Therma-Tru Hinged Patio Door System Single Panel Assembly Unit - page 8

    A TT ACH HINGES T O JAMB 6 Fasten Hinges to Hinge Jamb Place hinges into hinge mortise. Pre-drill 1/8” dia. pilot holes through jamb. Fasten top hinge with (2) #10 x 3/4” flat head screws in hole locations shown. Fasten middle and bottom hinges each with (3) #10 x 3/4” flat head screws leaving top hole vacant. Standard Hinge Option NOTE: Thes ...

  • Therma-Tru Hinged Patio Door System Single Panel Assembly Unit - page 9

    FRAME ASSEMBL Y 7 Fasten Side Jambs to Head Jamb Butt and align head jamb to side jambs. Pre-drill 1/8” dia. pilot holes through side jamb into head jamb. Fasten side jambs to head jamb with (3) #10 x 2 1/2” flat head screws through lock and hinge jamb into head jamb. Apply End Seal Pads Remove from paper backing and apply adhesive side of end ...

  • Therma-Tru Hinged Patio Door System Single Panel Assembly Unit - page 10

    FRAME ASSEMBL Y - continued 7 Outswing Sill Option Partially Set Sill Screws in Jambs Drive (1) #8 x 2” flat head screw through holes in both side jambs until tips barely protrude through jamb face. Caulk Entire Sill Gain Apply a 1/4” bead of sealant to sill gain and a bead that matches upper profile of sill. Fasten Sill to Jamb Use screw point ...

  • Therma-Tru Hinged Patio Door System Single Panel Assembly Unit - page 11

    FLANGE INST ALLA TION 8 Align and Install Side Flanges Align edge of side flange with bottom of side jambs. Firmly press into kerf in jamb using a rubber mallet if necessary . Flange will be set back approximately 1/2” from top edge of jamb. Install T op Flange Center top flange into head jamb kerf and press into place using a rubber mallet if ne ...

  • Therma-Tru Hinged Patio Door System Single Panel Assembly Unit - page 12

    DOOR INST ALLA TION 9 Place Door into Frame Lay frame on flat surface with hinges on jamb pointed up as shown. Slide door down on top of skids. Make 2 “Insert Skids” Make from 2 x 6 boards. Door Frame Hinge Skid (2) Hinge Door Jamb Skid 4-9/16" Jambs 6-9/16" Jambs Hinge Door Skid Jamb Standard Hinge Option NOTE: It is recommended to c ...

  • Therma-Tru Hinged Patio Door System Single Panel Assembly Unit - page 13

    DOOR INST ALLA TION - continued 9 Engage Hinge Knuckles T ap with hammer or rubber mallet as required to line up hinge knuckles and engage. Install Hinge Pins T ap in pins. Be certain to insert pins so heads are on top edges of hinges. Hinge Pin Door Door Frame #8 x 3/4” flat head screws Adjustable Hinge Option Fasten door panel to frame Prop up ...

  • Therma-Tru Hinged Patio Door System Single Panel Assembly Unit - page 14

    A TT ACH TRANSPOR T CLIP 10 Standard Lock Option Attach Transport Clip to Door Insert tab into latch bore. Position reference lip at edge of stile against exterior side of door. Fasten with (2) #6 x 3/4” flat head screws. Multi-point Lock Option Attach Transport Clip to Frame Close door into frame ensuring margins are even at head jamb. Fasten tr ...

  • Therma-Tru Hinged Patio Door System Single Panel Assembly Unit - page 15

    A TT ACH TRANSPOR T CLIP - continued UNIT READ Y FOR INST ALLA TION 10 11 Attach Transport Clip to Frame Close door into frame ensuring margins are even at head jamb. Fasten transport clip to frame with (2) #6 x 3/4” flat head screws. Unit can now be transferred for installation. Gather any remaining components and hardware as they may be used fo ...

  • Therma-Tru Hinged Patio Door System Single Panel Assembly Unit - page 16

    1687 W oodlands Dr. Maumee, OH 43537 1-800-THERMA TRU (843-7628) www.thermatru.com P A TIO DOOR S Y STEMS © 2004 Therma-Tru Corp. Therma-Tru Doors is an operating company of Fortune Brands, Inc. Part # AIHPSNGL 03-01-04 ...

メーカー Therma-Tru カテゴリー Door

Therma-Tru Hinged Patio Door System Single Panel Assembly Unitのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- Hinged Patio Door System Single Panel Assembly Unitの取扱説明書
- Therma-Truの製品カード
- パンフレット
- またはTherma-Tru Hinged Patio Door System Single Panel Assembly Unitの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Therma-Tru Hinged Patio Door System Single Panel Assembly Unitの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Therma-Tru Hinged Patio Door System Single Panel Assembly Unitの取り付け説明書、サービスマニュアル、簡易説明書、またはTherma-Tru Hinged Patio Door System Single Panel Assembly Unitのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Therma-Tru Hinged Patio Door System Single Panel Assembly Unitの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Therma-Tru Hinged Patio Door System Single Panel Assembly Unitデバイスの取扱説明書はどのようなものですか？
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがTherma-Tru Hinged Patio Door System Single Panel Assembly Unitを使用するのを助ける技術的文書のことです。説明書は通常、全てのTherma-Tru Hinged Patio Door System Single Panel Assembly Unitユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Therma-Truの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Therma-Tru Hinged Patio Door System Single Panel Assembly Unitの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははTherma-Tru Hinged Patio Door System Single Panel Assembly Unitの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Therma-Tru Hinged Patio Door System Single Panel Assembly Unitに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Therma-Tru Hinged Patio Door System Single Panel Assembly Unitデバイスの基本機能を使うにあたってのヒント。 Therma-Tru Hinged Patio Door System Single Panel Assembly Unitのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Therma-Tru Hinged Patio Door System Single Panel Assembly Unitに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるTherma-Tru Hinged Patio Door System Single Panel Assembly Unitのメーカー/サービスへの連絡先に関する情報。

Therma-Tru Hinged Patio Door System Single Panel Assembly Unitについてご質問がありますか？

次のフォームを使用してください

見つけた説明書を読んでもTherma-Tru Hinged Patio Door System Single Panel Assembly Unitの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがTherma-Tru Hinged Patio Door System Single Panel Assembly Unitで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

Captcha
新しい画像

コメント (0)