-
Numark Industries TT200 - page 1
OPERATING INSTRUCTIONS CONTENTS Setup & Installation 2 Platter Setup 3 Cartridg e Setup 4 Interchangin g T onearm T ubes 5 To n e A r m S e t u p 6 Cont ro ls 7 Cable Setup 10 Specifications 11 T r ouble Sh ooting 12 ...
-
Numark Industries TT200 - page 2
SETUP & INSTALLATION This turntable has been designed exclusive ly for DJ use and can be setup in a v ariety of different w ays dependin g on your mixing style. The tu rntable sh ould rest on a level and st able surface t hat is clear of obstr uctions. If a mixer is placed between two tu rnta bles make sure that there is at least ¼" (7mm) ...
-
Numark Industries TT200 - page 3
PLATTER SETUP WARNING: Incorrect Platte r setup can lead t o poor turntable performance , platter instability , or permanent motor damage. 1. Start by in specting the bottom of the aluminum pla tter to check that bo th locking pins ha ve rubber fittings on them. 2. Next, rot ate the top of the m otor assembly (brass in color) so that two holes ar e ...
-
Numark Industries TT200 - page 4
CARTRIDGE SETUP For Head Shell Mounted Cartridg es: The cartridge th at comes with t his turntable sho uld be preinstalled on the head shell. If it isn't, please follow the below i nstructions for installing a c artridge onto the head sh ell. 1. Position the head shell and the cartridge so that the four connector p ins are visible. Mak e sure ...
-
Numark Industries TT200 - page 5
INTERCHANGING TONEARM TUBES (sold seperately) WARNING: An incompl ete underst anding of this pr ocedure could lead to permanent damage to the headshell, your reco rds, or the tonearm assemb ly . NOTICE: Interchangi ng tonearm tubes un necessarily m ay shorten the life o f the tonearm tube s and/or tonea rm comp onents. This turntable feature s the ...
-
Numark Industries TT200 - page 6
TONE ARM SETUP A properly adjusted tone arm and cartridge setup wi ll minimize viny l record wear and optimize the performance of the turntable. Follow these simple s teps fo r setti ng the tone arm on the tur nta ble: NOTE: In most cases, when using the S-Shaped tone arm tube, the additional S-Weight must be fas tened to the tonearm to achieve pro ...
-
Numark Industries TT200 - page 7
PAG E 7 CON T R OL S CONTROLS General Controls 1. P owe r Button Pushing this button down turns on the turntable . It illuminates red w hen the turntable is switched on. 2. Start/ Stop Butt ons These buttons start and stop the turntable mo tor . Both buttons hav e the same function. 3. Pl atter This turntable has a special edge design tha t has bee ...
-
Numark Industries TT200 - page 8
CABLE SETUP PAGE 8 CONTROLS continued Tone Arm Parts 10. Counterweight and Scale Ring and S- W eight 11 10 The Counterweight is used to balance the head shell and cartridg e assembly so t hat the prop er amount of stylus pressure is applied to the record. The S-W eight (sold seperately with S-arm tube) shou ld be used in most cases 12 when the S-Sh ...
-
Numark Industries TT200 - page 9
PAG E 9 CON T R OL S CONTROLS continued Bottom Parts 18. Adjustable Rubber Dampening Feet When all of the feet of the turntable are completely ti ghte ned, the to p flat surfa ce of t he tu rntable will be at 85mm. Unscrewing these feet r aises the turn table up to compensa te for unleveled sur faces. 19. Carrying Handles These handles p rovide a s ...
-
Numark Industries TT200 - page 10
CABLE SETUP PAGE 10 CABLE SE TUP This turntable is shippe d with two sets of special cabl es: (1) Right Angle IEC Power Cord (1) Right Angle RCA cord w/ground wire NOTE: Before connecting any cables, make sure that th e voltage selector switch is set to the proper setting! Making the power and audio connections: 1. Begin by li fting the turntable u ...
-
Numark Industries TT200 - page 11
SPECIFICATIONS Turntable Section: T ype: 3 speed, fully manual Motor: Direct Drive- 8 P ole, 3 Phase Starting T orque: 1.6 kg/cm Start Time: 0-33.33 RPM in 0.8 sec Braking S ystem: Electronic Se rvo Br ake Platter: Aluminum Diecast Speeds: 33.33, 45, and 78 RPM W ow & Flutt er: <0.2% WRMS Separ ation: 20 dB Rumble: -40dB (IEC 98A Un weighted ...
-
Numark Industries TT200 - page 12
Problem Cause? Solution T urntable d oes not turn on. D isconnected Power Cord? Connect Power Cord. The sou nd leve l is very l ow. The T urn table is not conn ected to a device wit h a PHONO preamp . Connect the device to a preamp DJ mixer or an AV receiver that has an input la beled PHONO , not AU X or LINE. The sound is on one side only . The Ca ...
-
Numark Industries TT200 - page 13
INSIDE THE BOX: (1) TT-200 w/Straight Tonearm (1) Aluminum Platter (1) Slipmat (1) Head shell (1) 2.5 Gram Headshell Weight (1) Counter Weight (1) 45 RPM Adapter (1) IEC Power Cable (1) RCA Cord w/ Ground Wire (1) Service Tool TT -200 Manual /English, R3.1 Copyright Numark I ndustries, LL C 2003 ...
Numark Industries TT200についてご質問がありますか？
次のフォームを使用してください
見つけた説明書を読んでもNumark Industries TT200の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがNumark Industries TT200で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。