-
Jura Capresso Z5 - page 1
IMPRESSA Z5 Instructions for use 9/05 Art. Nr. 65475 ...
-
Jura Capresso Z5 - page 2
= Note = Important = Tip JURA Elektroapparate AG, CH-4626 Niederbuchsiten, Internet http://www.jura.com ...
-
Jura Capresso Z5 - page 3
Fig. 1 Fig. 2 Fig. 3 Fig. 4 Fig. 5 Fig. 6 Fig. 8 Fig. 9 Fig. 10 Fig. 11 Fig. 12 Fig. 13 Fig. 7 c b a 1 Fig. 14 Fig. 13: Correct assembly of the cappuccino nozzle Make sure there is always a small gap between the rear cappuccino nozzle and the connection piece. This will guarantee perfect operation of the cap- puccino nozzle. ...
-
Jura Capresso Z5 - page 4
1 2a 3 7 6 5 4b 4a 8 9 15 14 13 12 11 10 AC B D EG FJ KM L H I 16 a 16 b 2b ...
-
Jura Capresso Z5 - page 5
Description of the machine 1. Drip tray 2. a) Drip grate b) Cup platform 3. Coffee grounds tray and container 4. a) One Touch Cappuccino nozzle* long spout b) One Touch Cappuccino nozzle* short spout 5. Water tank with handle and level indicator 6. Water tank cover 7. Cover for bean tank and coffee powder tank 8. Aroma preservation cover 9. Filler ...
-
Jura Capresso Z5 - page 6
6 Contents 1. Safety information .............................................. page 7 1.1 Warning .................................................. page 7 1.2 Precautions .............................................. page 7 2. Preparing the IMPRESSA Z5 ............................... page 7 2.1 Check supply voltage .............................. ...
-
Jura Capresso Z5 - page 7
7 Introduction Thank you for purchasing the IMPRESSA Z5. To ensure perfect functioning of your IMPRESSA, carefully read this operating manual and keep it for future reference. Should you need more information or if you encounter particular problems not specified in these operating instructions in sufficient detail, either contact us directly or con ...
-
Jura Capresso Z5 - page 8
8 2.2 Check electrical fuse The IMPRESSA Z5 is designed for an electric current of 10 amperes. Check if the electrical fuse has sufficient capacity. 2.3 Fill water tank Only use fresh, cold water. Never fill in milk, mineral water or other liquids. Remove the water tank and rinse it with cold tap water thoroughly (Fig. 1). Then fill the wat ...
-
Jura Capresso Z5 - page 9
9 2.6.2 Stainless steel vacuum milk container (16b) Always clean the stainless steel vacuum milk container after you have used it. Rinse it with warm water, and with some detergent if necessery Remove the riser tube inside the milk container as well as the hose connection on the outside and give these parts including the lid a good rinse with c ...
-
Jura Capresso Z5 - page 10
10 CONFIRMED √ PRESS MAINTENANCE Maintenance key (C) lights up. Place a cup each under the height-adjustable coffee spout (12) and the cappuccino nozzle (4) and press the maintenance key (C). SYSTEM FILLS The system now fills up automatically. While it is doing so, the maintenance key flashes. (A little water w ...
-
Jura Capresso Z5 - page 11
11 COFFEE READY Press the Rotary Switch (B) until you hear an acoustic signal. FILTER NO Turn the Rotary Switch (B) until the following message is dis- played: HARDNESS 16°dH Now press the Rotary Switch (B) to start programming. HARDNESS 16°dH Now turn the Rotary Switch until the correct water hardn ...
-
Jura Capresso Z5 - page 12
12 INSERT FILTER PRESS BUTTON Remove the water tank from the IMPRESSA. Empty out any remaining water. Fold up the cartridge holder (Fig.6). Attach the extension piece to the top of the CLARIS plus filter cartridge. Now insert the filter cartridge in the water tank, applying gentle pressure (Fig. 6). Close the cartridge holder until ...
-
Jura Capresso Z5 - page 13
13 6. Rinsing the machine If the coffee machine is switched off and has cooled down, you will be prompted to start a rinsing cycle when switching the machine back on. The machine automatically performs a rinsing cycle when you switch it off. PRESS MAINTENANCE Place a cup under the height-adjustable coffee spout (11). Press the maint ...
-
Jura Capresso Z5 - page 14
14 COFFEE READY To stop the brewing process prematurely, press any of the product keys. You can pre-select the strength of your coffee when the ma- chine is ready to brew ( PLEASE SELECT). To do so, turn the Rotary Switch (B) until the display indicates the desired coffee strength and then press the coffee key of your choice (key F for spec ...
-
Jura Capresso Z5 - page 15
15 CAPPU RINSE Place a sufficiently large receptacle (ca. 0.5 litres) under the cap- puccino nozzle (4). Turn the selector switch (1, Fig. 9) to the steam range (c, Fig. 9). Press the maintenance key (C) to start the cappuccino rinsing cycle. CAPPUCCINO RINSING COFFEE READY You can also trigger a cappuccino rinsing c ...
-
Jura Capresso Z5 - page 16
16 MACHINE IS CLEANING COFFEE READY 9.4 Cleaning the cappuccino nozzle Despite the cappuccino cleaning cycle, you should regularly disassemble the cappuccino nozzle and rinse it under running water. Remove the cappuccino nozzle from the IMPRESSA and take it apart as shown in Fig. 11. Thoroughly rinse all the parts of the noz ...
-
Jura Capresso Z5 - page 17
17 You can change the amount of water set while the machine is dispensing hot water. To do so, turn the Rotary Switch (B) until the display indicates the required amount (ML). The amount of water can be selected in increments of 5 ML. The amounts given in ML are approximate values and may vary from the effective quantity. 12. Brewing coffee using p ...
-
Jura Capresso Z5 - page 18
18 Switch the IMPRESSA off with the ON / OFF switch (A). GOODBYE The coffee spout is rinsing. RINSE LEFT SPOUT PRESS BUTTON Press the maintenance key (C) to continue rinsing. GOODBYE When switching the machine off, there may be a hissing sound. This is due to a normal process being performed by the system. It is ...
-
Jura Capresso Z5 - page 19
19 When the machine has dispensed as much milk as you wanted, briefly press the key once more. CONFIRMED √ The amount of milk to be dispensed is now programmed. ENOUGH ? PRESS BUTTON When you have made as much coffee as you wanted, briefly press the key once more. CONFIRMED √ The amount of coffee to be ma ...
-
Jura Capresso Z5 - page 20
20 15. Programming The IMPRESSA leaves the factory with a number of default settings that allow you to make coffee without having to pro- gram the machine first. You can, however, adjust various parameters to make the coffee suit your personal taste. The following parameters can be programmed: Filter Water hardness Maintenance Tempe ...
-
Jura Capresso Z5 - page 21
21 COFFEE READY Press the Rotary Switch (B) until you hear an acoustic signal. FILTER NO or YES Turn the Rotary Switch (B) until the following message is dis- played: TEMPERATURE Press the Rotary Switch (B) to start programming. TEMPERATURE COFFEE READY Then press a product key of your choice. 1 E ...
-
Jura Capresso Z5 - page 22
22 √ AROMA Now turn the Rotary Switch (B) until the following message is displayed: EXIT Now press the Rotary Switch (B) to leave the programming mode. COFFEE READY 15.6 Cappuccino programming You can also make the cappuccino settings in the program- ming mode or as described in Chapter 14.2 “Cappuccino set- ...
-
Jura Capresso Z5 - page 23
23 Press the Rotary Switch (B) until you hear an acoustic signal. FILTER NO or YES Turn the Rotary Switch (B) until the following message is dis- played: MILK 20 SEC (example) Now press the Rotary Switch (B) to start programming. MILK 20 SEC (example) Now turn the Rotary Switch (B) until the required amou ...
-
Jura Capresso Z5 - page 24
24 Now press the Rotary Switch (B) to leave the programming mode. COFFEE READY Save energy: No Selecting this level puts the IMPRESSA in constant stand-by mode. This setting allows you to make coffee or frothed milk without having to wait for the machine to heat up. This setting is useful if you make a lot of coffee and milk products an ...
-
Jura Capresso Z5 - page 25
25 TIME 13:50 Now turn the Rotary Switch (B) until the following message is displayed: EXIT Now press the Rotary Switch (B) to leave the programming mode. COFFEE READY 15.10 Programming the automatic switch-on time COFFEE READY Press the Rotary Switch (B) until you hear an acoustic signal. FILTER ...
-
Jura Capresso Z5 - page 26
26 OFF AFTER 5 HRS Now press the Rotary Switch (B) to start programming. OFF AFTER 5 HRS Turn the Rotary Switch (B) to set the switch-off time. OFF AFTER 4 HRS (example) Confirm the automatic switch-off time by pressing the Rotary Switch (B). CONFIRMED √ OFF AFTER 4 HRS Now turn the Rotary S ...
-
Jura Capresso Z5 - page 27
27 COFFEE READY 15.13 Renaming This function allows you to rename the different products as well as change the welcome and end text. COFFEE READY Press the Rotary Switch (B) until you hear an acoustic signal. FILTER NO or YES Turn the Rotary Switch (B) until the following message is dis- played: RENAME No ...
-
Jura Capresso Z5 - page 28
28 15.14 Programming the language COFFEE READY Press the Rotary Switch (B) until you hear an acoustic signal. FILTER NO or YES Turn the Rotary Switch (B) until the following message is dis- played: LANGUAGE ENGLISH Now press the Rotary Switch (B) to start programming. LANGUAGE ENGLISH Turn the Rotary ...
-
Jura Capresso Z5 - page 29
29 Now turn the Rotary Switch (B) until the following message is displayed: EXIT Now press the Rotary Switch (B) to leave the programming mode. COFFEE READY Changing the time format COFFEE READY Press the Rotary Switch (B) until you hear an acoustic signal. FILTER NO or YES Turn the Rotary Switch (B) ...
-
Jura Capresso Z5 - page 30
30 16.2 Emptying the coffee grounds GROUNDS EMPTY If this information is displayed, the machine will no longer make coffee. The machine will still make hot water and frothed milk, however. Empty the coffee grounds container (3). On the IMPRESSA Z5 Chrome we recommend that the cup platform (2b) is removed first followed by the drip tray and ...
-
Jura Capresso Z5 - page 31
31 Insert the drip tray (3). COFFEE READY 16.6 Filling the bean tank COFFEE READY FILL BEANS If this information is displayed, the machine will no longer make coffee. The machine will still make hot water and frothed milk, however. Refill beans as described in Chapter 2.4. COFFEE READY 16.7 Aroma preservation cover missi ...
-
Jura Capresso Z5 - page 32
32 After another 10 products, the display will change. Please run the cleaning cycle immediately (see Chapter 17). CLEAN NOW CLEAN (flashing) 16.11 Information about decalcify Lime scale builds up in the IMPRESSA as a result of normal use. The degree of calcification depends on the hardness of the water you use. The IMPRESSA Z5 recognizes w ...
-
Jura Capresso Z5 - page 33
33 TRAY / GROUNDS EMPTY Empty the drip tray (1) and the coffee grounds tray with the con- tainer (3). TRAY MISSING Place the empty, clean drip tray (1) and the coffee grounds tray with the container (3) back into the IMPRESSA. PRESS BUTTON Place a sufficiently large receptacle (ca. 0.5 litres) each under the heig ...
-
Jura Capresso Z5 - page 34
34 Once started, the decalcifying program must not be inter- rupted. Always wait until the decalcifying agent has been used up and the tank is empty. Never fill in additional descaling agent. COFFEE READY DESCALE Press the maintenance key (C). TRAY / GROUNDS EMPTY Empty the drip tray (1) and the coffee grounds tray with the ...
-
Jura Capresso Z5 - page 35
35 You will hear an acoustic signal. TRAY / GROUNDS EMPTY Empty the drip tray (1) and the coffee grounds tray with the container (3). TRAY MISSING Place the empty, clean drip tray (1) and the coffee grounds tray with the container (3) back into the IMPRESSA. COFFEE READY You can also trigger a decalcifying cycle ...
-
Jura Capresso Z5 - page 36
36 21. Problems Problem Cause Remedy Very loud noise coming from the grinding Foreign body in grinding gear Please refer to Chapter 16.8 gear Frothing spout squirts Milk hose not properly attached Make sure the milk hose is properly attached Too little froth when frothing milk Cappuccino nozzle clogged Clean nozzle (Chapter 9.4) Coffee only drips f ...
-
Jura Capresso Z5 - page 37
37 22. Legal information These operating instructions contain all the information required for using, operating and maintaining the machine properly. Knowledge of and compliance with the specifications contained in these operating instructions is required for using the machine safely as well as for operational safety and safety during maintenance. ...
Jura Capresso Z5についてご質問がありますか？
次のフォームを使用してください
見つけた説明書を読んでもJura Capresso Z5の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがJura Capresso Z5で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。