Simplicity 1691411の取扱説明書

20ページ 0.41 mb
ダウンロード

ページに移動 of 20

Summary
  • Simplicity 1691411 - page 1

    O PERATOR ’ S M ANUAL Sno-Away Models 5-55cd22 7-55cd22 Mfg. No. 1691411 Mfg. No. 1691413 Mfg. No. 1691414 ...

  • Simplicity 1691411 - page 2

    BakerTM O PERATOR ’ S M ANUAL Model 7/22E ...

  • Simplicity 1691411 - page 3

    II 500 N. Spring Street, P.O. Box 997 Port Washinnton, WI 53074-0997 ...

  • Simplicity 1691411 - page 4

    ...

  • Simplicity 1691411 - page 5

    Table Of Contents SAFETY RULES General ........................................................... 2 Preparation.. .................................................. .2 Operation.. ..................................................... .2 Maintenance & Storage.. .............................. .3 Safety Decals .................................... ...

  • Simplicity 1691411 - page 6

    WARNING This unit is a “two-stage” snowthrower. The first stage is the auger, which feeds the snow back into the impeller housing. The second stage is the impeller, which throws the snow out the discharge chute. If bodily contact is made with the auger or impeller when they are rotating, severe personal injury will occur. To avoid injury, keep ...

  • Simplicity 1691411 - page 7

    Safety Rules l Always refer to the Operator’s Manual for important details if snowthrower is to be stored for an extended period. l Run auger drive a few seconds after completion of throwing snow to help clear out snow and prevent freeze-up. SAFETYDECALS Safety warning decals are placed at strategic locations on the snowthrower as a constant remi ...

  • Simplicity 1691411 - page 8

    Controls SNOWTHROWER CONTROLS (Figure 1) Ref A B i C D E Name Auger Control Clutch Lever Drive Control Clutch Lever Chute Control Rod Chute Deflector Skid Shoes Function Engages auger/impeller when depressed; disengages when released. Engages drive to wheels when depressed; disengages when released. Controls direction snow is thrown. Controls angle ...

  • Simplicity 1691411 - page 9

    DEFLECTOR The angle and distance of the discharged snow is con- trolled by the position of the deflector. Engine speed also affects distance of discharge. The more the deflector is tilted back, the farther snow will be thrown. Loosen the knob (figure 3) to tilt the deflector back or forward, then retighten the knob. SCRAPER BAR & SKID SHOES On ...

  • Simplicity 1691411 - page 10

    Operation GENERAL I A WARNING A WARNING Before leaving the operator’s area for any reason, stop the engine and remove the key. Disconnect the spark plug wire and secure it away from the plug to prevent accidental start-up of the snowthrower. Gasoline is highly flammable and must be handled with care. Never fill the tank when the engine is hot 1 f ...

  • Simplicity 1691411 - page 11

    Operation 7. As the engine warms up and begins to operate even- ly, turn the choke knob slowly counterclockwise to the OFF position. If engine falters, return to l/2 choke position until it runs smoothly, then turn it to the choke OFF position. NOTE: Allow the engine to warm up for a few minutes before operating the snowthrower. Engine will not dev ...

  • Simplicity 1691411 - page 12

    Regular Maintenance NORMAL CARE I Every 25 Care Reauired See Paae Hours -a Check auger gear case lubrication.* Page 8 . I Lubricate snowthrower. Paae9 I . 1 Check tire pressure. I Paae 9 I l I 1 Change engine oil.**+ Clean or replace spark plug.+ . I I . i I Check discharge control. 1 Page 14 I I * I * The transmission and auger gear case have been ...

  • Simplicity 1691411 - page 13

    Regular- Maintenance LUBRICATION CHECKING TIRE PRESSURE A CAUTION It is very important that grease fittings on auger shaft (figure 6) are lubricated regularly. If auger rusts to shaft, damage to worm gear may occur if shear pins do not break. With an oil can, apply medium weight (IOW) oil to points A & i3 shown in figure 7. There are two grease ...

  • Simplicity 1691411 - page 14

    A WARNING Before performing any adjustment or service to snowthrower, stop the engine and wait for moving parts to stop. Remove the key. To prevent acciden- tal starting, disconnect the spark plug wire and fasten away from the plug. This section provides troubleshooting and service instructions. For problems not covered here, contact your dealer. T ...

  • Simplicity 1691411 - page 15

    SHIFT CONTROL ADJUSTMENT If any of the following conditions exist, it will be neces- sary to adjust the shift control. l Snowthrower is not in neutral when shift lever is in NEUTRAL position. l Reverse position cannot be fully reached. l 3rd gear cannot be fully reached. Adjust as follows: 1. Locate neutral position of shift lever by moving unit ba ...

  • Simplicity 1691411 - page 16

    Adjusting Drive Belts If the auger or wheels slip under load, belts could be stretched or worn. Adjust as follows: 1. Remove the belt cover (figure 10). Determine which belt requires adjustment. 2. Loosen the locknut on the appropriate idler pulley and move the idler pulley i/4” toward the belt (figure 11). Tighten the locknut. 3. Re-install the ...

  • Simplicity 1691411 - page 17

    A CAUTION Place a block (approximately 4” high) under front edge of auger housing or snowthrower will not stand on end. 6. See figure 13. Loosen nuts holding lower belt guard and slide guard away from belt. 7. Remove belt from between large pulleys. 13. Slide new belt onto pulley and position lower belt guard to within l/16” - i/8” of large d ...

  • Simplicity 1691411 - page 18

    WHEEL AXLE BEARING REPLACEMENT After approximately 100 hours of use (about 5 years), or if drive chain jumps off sprockets, wheel axle bearings may need to be replaced. 1. Disconnect spark plug wire and fasten it away from the spark plug. 2. Place a block under the snowthrower so the wheels are just off the ground. 3. See figure 16. Remove the ring ...

  • Simplicity 1691411 - page 19

    Specifications ENGINE Make ................................................................ Tecumseh Cylinders.. ..................................................................... .1 Cycles ............................................................................. 4 Crankshaft ....................................................... Horizontal ...

  • Simplicity 1691411 - page 20

    Replacement Parts %I Accessories COMMON REPLACEMENT PARTS Listed below are part numbers for the more common replacement parts. Use only genuine Simplicity replace- ment parts to assure optimum performance and safety. Special Worm Gear Oil for Auger Gear Case - 8 oz. Container.. .............................................. .1704636 - Case of 8 oz. ...

メーカー Simplicity カテゴリー Snow Blower

Simplicity 1691411のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 1691411の取扱説明書
- Simplicityの製品カード
- パンフレット
- またはSimplicity 1691411の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Simplicity 1691411の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Simplicity 1691411の取り付け説明書、サービスマニュアル、簡易説明書、またはSimplicity 1691411のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Simplicity 1691411の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Simplicity 1691411デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがSimplicity 1691411を使用するのを助ける技術的文書のことです。説明書は通常、全てのSimplicity 1691411ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Simplicityの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Simplicity 1691411の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははSimplicity 1691411の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Simplicity 1691411に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Simplicity 1691411デバイスの基本機能を使うにあたってのヒント。 Simplicity 1691411のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Simplicity 1691411に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるSimplicity 1691411のメーカー/サービスへの連絡先に関する情報。

Simplicity 1691411についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもSimplicity 1691411の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがSimplicity 1691411で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)