-
Ultratec PFI-9D - page 1
Power F ogger Industrial Line and PFI w/ LSG Operator’ s Manual www .ultratecfx.com VER. 30.10.10 ...
-
Ultratec PFI-9D - page 2
T able of Contents Introduction ................................................................................ 3 Micropr ocessor Control ............................................................ 3 W ater Base Fog T echnology ...................................................... 3 W ar ning ..................................................... ...
-
Ultratec PFI-9D - page 3
www .ultratecfx.com 3 Intr oduction The Power Fogger Industrial is a Micropr ocessor Controlled, W ater Based Fog generating system. Micr oprocessor Contr ol The PFI features dual micr oprocessor control. Fr om temperature r egulation to taper back ow control, all of the functions are monitor ed and processed by the two on-board pr ocessors. W a ...
-
Ultratec PFI-9D - page 4
www .ultratecfx.com 4 PFI T echnical Specications Model: PFI/PFI-9D Part Number: PFI CLF 4450 / 120 volt CLF 4451 / 220-240 volt PFI-9D CLF 4460 / 110 volt CLF 4461 / 220-240 volt Power Rating: 120 V olt A.C. 50/60 Hz. 13 Amps. 240 V olt A.C. 50/60 Hz. 6.5 Amps. Fluid: W ater Base Fog Fluid (Use only Ultratec Fluid) PFI T echnical Drawings Power ...
-
Ultratec PFI-9D - page 5
www .ultratecfx.com 5 Power Fogger Industrial 9D ...
-
Ultratec PFI-9D - page 6
www .ultratecfx.com 6 LSG PFI System in a Roadcase 39.5 28.75 34.5 23.25 29.6 24 20 36 32.2 22 28.02 LSG w/ PFI T echnical Drawings LSG PFI System on a Cart ...
-
Ultratec PFI-9D - page 7
www .ultratecfx.com 7 Operating Pr ocedure 1. The fog machine must be connected to a grounded supply of at least 15 amps fr ee of any interference. 2. Open a 20 Litre (5 Gallon) container of Ultratec Special Ef fects fog uid and insert the uid pickup tube into the spout of the uid container . 3. Connect the Remote Handset into the rear pan ...
-
Ultratec PFI-9D - page 8
www .ultratecfx.com 8 Operation Pr ocedure LSG MK II High Pr essure w/ 20 & 50lbs Cylinders The Operation Procedur es outlined in this section, refer to Figure A and Figur e B on Page 9 and 10 . 1. Place the fog machine’ s output nozzle rmly against the center of the foam ring, sealing it to the input port of the LSG MK II. T ech Tip: Pr o ...
-
Ultratec PFI-9D - page 9
www .ultratecfx.com 9 9. V erify cool temperature output by using your hand and passing it thr ough the fog-CO2 output noting the temperature. 10. After use, tur n off the valves and trigger the LSG MK II to depr essurize the system before attempting to disconnect hoses. Note that the valves and lines may be extremely cold during operation. Pr even ...
-
Ultratec PFI-9D - page 10
www .ultratecfx.com 10 Figur e B Liquid Carbon Dioxide LSG Control Signal Installation Model Shown Above T ouring Model Available High Pressure Bottles w/ Liquid Siphon Tube Liquid Carbon Dioxide Liquid Siphon T ube Fog Fluid ...
-
Ultratec PFI-9D - page 11
www .ultratecfx.com 11 Operation Pr ocedure LSG MK II Low Pr essure w/ 350lbs Dewar T ank The Operation Procedur es outlined in this section, refer to Figure C on Page 12. 1. Place the fog machine’ s output nozzle rmly against the center of the foam ring sealing it to the input port of the LSG MK II. T ech Tip: Proper alignment can be observed ...
-
Ultratec PFI-9D - page 12
www .ultratecfx.com 12 10. V erify cool temperature output by using your hand and passing it through the fog-CO2 output noting the temperature. 11. After use, tur n off the valves and trigger the LSG MK II to depr essurize the system before attempting to disconnect the hoses. Note that the valves and lines may be extremely cold during operation. Pr ...
-
Ultratec PFI-9D - page 13
www .ultratecfx.com 13 Options Remotes - The Show Control Remote and Timer/ Duration Remote are compatible with the Power Fog Industrial, Power Fog Industrial w/ Air Option, Power Fog Industrial 9D and Power Fog Industrial 9D w/ Air Option. Each remote is sold separately . Jug Holder - The Power Fog Industrial 9D and Power Fog Industrial 9D w/ Air ...
-
Ultratec PFI-9D - page 14
www .ultratecfx.com 14 Closed “Dry” Contact Show Control Show Contr ol Operation Show control is achieved by connecting a “Dry” or zer o voltage contact to the show control terminals. The Power Fog Industrial r equires no power to signal the fog, only one set of contacts that close for the entire fogging cue. For Show Control Operation, the ...
-
Ultratec PFI-9D - page 15
www .ultratecfx.com 15 DMX Operation The Power Fog Industrial is equipped with DMX controls as a standar d feature. 1. Attach a DMX signal to the DMX IN 5 pin connector on the rear of the unit. A terminator may be r equired on the DMX OUT connector in some applications. 2. Select a valid DMX address on the thumbwheel selector for the base addr ess ...
-
Ultratec PFI-9D - page 16
www .ultratecfx.com 16 Contact Information Head Ofce Ultratec Special Effects Inc. 1960 Blue Heron Drive London, Ontario N6H 5L9 Direct: 519-659-7972 T oll Free: 866-534-5557 Fax: 519-659-7713 Canadian Shipping Address (For All Canadian Repairs) Ultratec Special Effects Inc. 1960 Blue Heron Drive London, Ontario N6H 5L9 USA Shipping Address (For ...
Ultratec PFI-9Dについてご質問がありますか?
次のフォームを使用してください
見つけた説明書を読んでもUltratec PFI-9Dの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがUltratec PFI-9Dで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。