Chamberlain 3800の取扱説明書

32ページ 3.06 mb
ダウンロード

ページに移動 of 32

Summary
  • Chamberlain 3800 - page 1

    Owner’ s Manual ■ Please read this manual and the enclosed safety materials carefully! ■ Fasten the manual near the garage door after installation. ■ The door WILL NOT CLOSE unless The Protector System ® and cable tension monitor are connected and properly aligned. ■ Periodic checks of the opener are required to ensure safe operation. ? ...

  • Chamberlain 3800 - page 2

    2 INTRODUCTION Safety Symbol Review and Signal Wor d Review When you see these Safety Symbols and Signal Words on the following pages, they will alert you to the possibility of serious injury or death if you do not comply with the warnings that accompany them. The hazard may come from something mechanical or from electric shock. Read the warnings c ...

  • Chamberlain 3800 - page 3

    Safety Reversing Sensor Safety Reversing Sensor T orsion Spring Motor unit W all-mounted Control Console Access Door Gap between floor and bottom of door must not exceed 1/4" (6 mm). Power Door Lock Cable T ension Monitor Remote Light Drum 3 Planning Survey your garage area to see if any of the conditions below apply to your installation. Addi ...

  • Chamberlain 3800 - page 4

    4 Preparing your Garage Door Before you begin: • Disable locks. • Remove any ropes connected to garage door . • Complete the following test to make sure your garage door is balanced and is not sticking or binding: 1. Lift the door about halfway as shown. Release the door . If balanced, it should stay in place, supported entirely by its spring ...

  • Chamberlain 3800 - page 5

    5 2-Cond u ctor Bell W ire W hite & W hite/Red Safety La b els and Literat u re Remote Control V isor Clip Mo u nting Bracket SECURITY ✚ ® 3-B u tton Remote Control (1) (2) Safety Re v ersing Sensors (1 Sending Eye and 1 Recei v ing Eye) w ith 2-Cond u ctor W hite & W hite/Black Bell W ire attached Safety Sensor Bracket (2) Motor Unit LO ...

  • Chamberlain 3800 - page 6

    ASSEMBL Y STEP 1 Attach the Collar to the Motor Unit T o avoid installation difficulties, do not run the garage door opener until instructed to do so. • Loosen the collar screws. • Attach collar to either the left or the right side of the motor unit. Ensure that the collar is seated all the way on motor shaft until stop is reached (Figure 1). ? ...

  • Chamberlain 3800 - page 7

    7 INST ALLA TION INST ALLA TION STEP 1 Position the Opener 1. Close the garage door completely . 2. Slide the opener with collar over the end of the torsion bar . Check to make sure bracket is located on a solid surface such as wood, concrete or door/flag bracket. Snug collar screws to help assure proper alignment of operator . Mark the bracket hol ...

  • Chamberlain 3800 - page 8

    8 Staples Lock Scre w 1/4-20 x 1/2" (2) HARDW ARE SHOWN ACTUAL SIZE Approx. 3" (7.6 cm) Lock T emplate Roller Garage Door T rack TOP DRILL 5/16" DRILL 3/4" DRILL 5/16" 132A2505 TOP DRILL 5/16" DRILL 3/4" DRILL 5/16" 132A2505 Figure 1 INST ALLA TION STEP 3 Install Power Door Lock The lock is used to prevent th ...

  • Chamberlain 3800 - page 9

    9 W HT/GR N T o release w ire, p u sh in ta b w ith scre w dri v er tip Ca b le T ension Monitor 7/16" (1 1mm) Strip w ire 7/16" (1 1mm) W HT/GR N Ca b le T ension Monitor Ca b le T ension Monitor Roller Ca b le 2"-6" (5 cm- 15 cm) Dr u m T orsion Bar Opener 1/ 8 "-1/4" (3 mm-6 mm) W ith Door Closed Preferred Orientati ...

  • Chamberlain 3800 - page 10

    10 INST ALLA TION STEP 5 Install the Control Console Locate control console within sight of the door at a minimum height of 5 feet (1.5 m) where small children cannot reach, and away from moving parts of the door and door hardware. The installation surface must be smooth and flat. If installing into drywall (Figure 1), drill 5/32" holes and us ...

  • Chamberlain 3800 - page 11

    11 INST ALLA TION STEP 6 Install Remote Light The remote light is designed to plug directly into a standard 120V outlet. 1. Install the hinge and latch clips. Clips slide in between the metal plate and the plastic housing on each side of the light base (Figure 1). 2. Light should be mounted within 6' (1.8 m) of an electrical outlet and away fr ...

  • Chamberlain 3800 - page 12

    12 INST ALLA TION STEP 7 Electrical Requirements T o avoid installation difficulties, do not run the opener at this time. T o reduce the risk of electric shock, your garage door opener has a grounding type plug with a third grounding pin. This plug will only fit into a grounding type outlet. If the plug doesn't fit into the outlet you have, co ...

  • Chamberlain 3800 - page 13

    13 INST ALLA TION STEP 8 Mount the Battery Backup Unit (BBU) (not provided) If the optional 475LM battery backup unit is part of this installation it should be installed at this time. • The BBU can be mounted to either the ceiling or a wall within 3' (.9 m) of the motor unit. • Position the BBU as desired to a structural support (ceiling j ...

  • Chamberlain 3800 - page 14

    14 In v isi b le Light Beam Protection Area Safety Re v ersing Sensor 6" (15 cm) max. a b o v e floor Safety Re v ersing Sensor 6" (15 cm) max. a b o v e floor Facing the door from inside the garage INST ALLA TION STEP 9 Install The Protector System ® The safety reversing sensor must be connected and aligned correctly before the garage d ...

  • Chamberlain 3800 - page 15

    15 DOOR TRACK MOUNT (RIGHT SIDE) Indicator Light Lens Lip Sensor Bracket Door Track FLOOR MOUNT (RIGHT SIDE) WALL MOUNT (RIGHT SIDE) Indicator Light Sensor Bracket Lens Extension Bracket (See Accessories) Inside G arage W all (Provided with Extension Bracket) (Provided with Extension Bracket) Figure 1 Figure 2 Figure 3 Figure 4 WALL MOUNT (RIGHT SI ...

  • Chamberlain 3800 - page 16

    16 In v isi b le Light Beam Protection Area S enso r Senso r Safety Re v ersing Sensor Bell W ire Bell W ire Motor u nit Safety Re v ersing Sensor Po w er Door Lock Q u ick-Connect Terminals W HT/BLK W HT W HT/RED W HT Sensor Connections T o Po w er Door Lock T o Ca b leT ension Monitor T o Control Console Connect W ire to Q u ick-Connect T erminal ...

  • Chamberlain 3800 - page 17

    17 T o prevent damage to vehicles, be sure fully open door provides adequate clearance. WARN ING CAUTION WARN ING WARN ING BLACK PURPLE Push and hold until the door is at desired UP position Figure 2 Figure 3 Push either button to stop door at desired DOWN position BLACK PURPLE Figure 4 or L O C K L IG H T Without a properly installed safety revers ...

  • Chamberlain 3800 - page 18

    18 ADJUSTMENT STEP 2 Setting the Force The force setting button is located on the front panel. The force setting measures the amount of force required to open and close the door . 1. Locate the purple button on the unit (Figure 1). 2. Push the purple button twice to enter unit into Force Adjustment Mode (Figure 2). The LED (Indicator Light) will fl ...

  • Chamberlain 3800 - page 19

    19 ADJUSTMENT STEP 3 T est the Safety Reversal System TEST • With the door fully open, place a 1-1/2" (3.8 cm) board (or a 2x4 laid flat) on the floor , centered under the garage door . • Operate the door in the down direction. The door must reverse on striking the obstruction. Upon successful safety reversal test proceed to Adjustment Ste ...

  • Chamberlain 3800 - page 20

    20 ADJUSTMENT STEP 5 T est Cable T ension Monitor If your cable tension monitor has been activated the LED will blink 9 times. ADJUSTMENT STEP 6 T est Power Door Lock TEST • With the door fully closed, the power door lock bolt should be protruding through the track. • Operate the door in the open direction. The power door lock should retract be ...

  • Chamberlain 3800 - page 21

    21 OPERA TION Using Y our Garage Door Opener Y our LiftMaster Security ✚ ® opener and hand-held remote control have been factory programmed to a matching code which changes with each use, randomly accessing over 100 billion new codes. Y our opener will operate with several Security ✚ ® remote controls up to 12 functions, and one Security ✚ ...

  • Chamberlain 3800 - page 22

    22 Using the W all-Mounted Control Console THE MOTION DETECTING CONTROL CONSOLE Press the push bar to open or close the door . Press again to reverse the door during the closing cycle or to stop the door while it's opening. This control console contains a motion detector that will automatically turn on the light when it detects a person enteri ...

  • Chamberlain 3800 - page 23

    23 CARE OF YOUR OPENER MAINTENANCE SCHEDULE Once a Month • Manually operate door . If it is unbalanced or binding, call a trained door systems technician. • Check to be sure door opens & closes fully . Adjust limits and/or force if necessary (See Adjustment Steps 1 and 2). • Repeat the safety reverse test. Make any necessary adjustments. ...

  • Chamberlain 3800 - page 24

    24 Having a Problem? (Continued) 5. The garage door opens and closes by itself: • Be sure that all remote control push buttons are off. • Remove the bell wire from the door control terminals and operate from the remote only . If this solves the problem, the door control is faulty (replace), or there is an intermittent short on the wire between ...

  • Chamberlain 3800 - page 25

    25 Y our garage door opener is programmed with self- diagnostic capabilities. The “Learn” button/diagnostic LED will flash a number of times then pause signifying it has found a potential issue. Consult Diagnostic Chart below . Diagnostic Char t Symptom: One or both of the Indicator lights on the safety reversing sensors do not glow steady . ? ...

  • Chamberlain 3800 - page 26

    26 *3-Button Remote If provided with your garage door opener , the large button is factory programmed to operate it. Additional buttons on any Security ✚ ® 3-Button remote or mini-remote can be programmed to operate other Security ✚ ® garage door openers. T o Erase All Codes Fr om Motor Unit Memory T o deactivate any unwanted remote, first er ...

  • Chamberlain 3800 - page 27

    27 1. Enter a four digit personal identification number (PIN) of your choice on the keypad. Then press and hold ENTER. 2. While holding the ENTER button, press and hold the LIGHT button on the Motion Detecting Control Console. 3. Continue holding the ENTER and LIGHT buttons while you press the push bar on the Motion Detecting Control Console (all t ...

  • Chamberlain 3800 - page 28

    28 1. Press the “learn button” on light until LED comes ON. 2. Activate the garage door using the hand-held remote, wall control or keyless entry . 3. It has learned the code and the light turns on. Reprogramming Light or Additional Light Y our garage door opener remote work light has already been programmed at the factory to operate with your ...

  • Chamberlain 3800 - page 29

    29 7 10 11 6 5 NO T IC E 8 1 4 2 3 9 12 L O C K L IG H T 13 14 Installation Parts REP AIR P ARTS KEY P ART NO. NO. DESCRIPTION 1 98LM Motion detecting control panel 2 373W 3-Button remote control 3 10A20 3V2032 lithium battery 4 29B137 Remote control visor clip 5 41A4582 E mergency release rope & handle assembly 6 41B4494-1 2-Conductor bell wir ...

  • Chamberlain 3800 - page 30

    30 1 2 3 4 5 6 KEY P ART NO. NO. DESCRIPTION 1 41DJ001 Logic board complete with plate 2 41A61 18 Absolute Encoder System 3 41C168 T ransformer KEY P ART NO. NO. DESCRIPTION 4 41A6095 Motor with bracket 5 41B122 Power cord 6 41A6348 Cover Motor Unit Assembly Parts ...

  • Chamberlain 3800 - page 31

    31 L O C K L I G H T CL OS E D O P E N ACCESSORIES 370LM 41A5281 377LM Extension Brackets: (Optional) For safety reversing sensor installation onto the wall or floor . Keyless Entry with Security ✚ ® : Enables homeowner to operate garage door opener from outside by entering a password on a specially designed keyboard. Also can add a temporary pa ...

  • Chamberlain 3800 - page 32

    LIFTMASTER ® SER VICE IS ON CALL OUR LARGE SERVICE ORGANIZA TION SP ANS AMERICA INST ALLA TION AND SERVICE INFORMA TION IS AS NEAR AS YOUR TELEPHONE SEVEN DA YS A WEEK. SIMPL Y DIAL OUR T OLL FREE NUMBER: 1-800-528-2817 HOURS: (Central Standard Time) 6:00 A.M. TO 7:00 P .M. - Monday through Friday 8:00 A.M. TO 6:00 P .M. - Saturday www .liftmaster ...

メーカー Chamberlain カテゴリー Garage Door Opener

Chamberlain 3800のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 3800の取扱説明書
- Chamberlainの製品カード
- パンフレット
- またはChamberlain 3800の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Chamberlain 3800の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Chamberlain 3800の取り付け説明書、サービスマニュアル、簡易説明書、またはChamberlain 3800のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Chamberlain 3800の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Chamberlain 3800デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがChamberlain 3800を使用するのを助ける技術的文書のことです。説明書は通常、全てのChamberlain 3800ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Chamberlainの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Chamberlain 3800の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははChamberlain 3800の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Chamberlain 3800に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Chamberlain 3800デバイスの基本機能を使うにあたってのヒント。 Chamberlain 3800のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Chamberlain 3800に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるChamberlain 3800のメーカー/サービスへの連絡先に関する情報。

Chamberlain 3800についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもChamberlain 3800の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがChamberlain 3800で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)