-
Grizzly G1036 - page 1
SLOW-SPEED GRINDER MODEL G1036 INSTRUCTION MANUAL COPYRIGHT © 1993 BY GRIZZLY INDUSTRIAL, INC. REG. TX 3 627 012 WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. REVISED FEBRUARY, 1999. PRINTED IN U.S.A. ...
-
Grizzly G1036 - page 2
G1036 Slow-Speed Grinder -2- Table Of Contents PAGE I. INTRODUCTION ........................................................................................................3 II. SAFETY RULES FOR ALL TOOLS ..........................................................................4 III. UNPACKING ...................................................... ...
-
Grizzly G1036 - page 3
-3- G1036 Slow-Speed Grinder We are proud to offer the Model G1036 Slow- Speed Grinder. The Model G1036 is part of a growing Grizzly family of fine woodworking machinery. When used according to the guidelines set forth in this manual, you can expect years of trouble- free, enjoyable operation and proof of Grizzly’s commitment to customer satisfac ...
-
Grizzly G1036 - page 4
G1036 Slow-Speed Grinder -4- 13. DO NOT OVERREACH. Keep proper footing and balance at all times. 14. MAINTAIN TOOLS IN TOP CONDITION. Keep tools sharp and clean for best and safest performance. Follow instructions for lubricating and changing accessories. 15 . DISCONNECT TOOLS FROM POWER before servicing and when changing acces- sories. 16. AVOID A ...
-
Grizzly G1036 - page 5
-5- G1036 Slow-Speed Grinder The Model G1036 Slow-Speed Grinder is shipped from the manufacturer in a carefully packed carton. If you discover the machine is damaged after you’ve signed for delivery, please call Customer Service immediately for advice. Save the containers and all packing materials for possible inspection by the carrier or its age ...
-
Grizzly G1036 - page 6
G1036 Slow-Speed Grinder -6- 1. Working Clearances: Consider existing and anticipated needs, size of material to be processed through the machine, and space for work tables or other machinery when establishing a location for your slow-speed grinder. The Model G1036 is wired for 110V, single phase operation; it cannot be operated on 220V. The 3 / 4 ...
-
Grizzly G1036 - page 7
-7- G1036 Slow-Speed Grinder Figure 1. Knob to adjust eye shield. A. EYE SHIELD Attach the plastic eye shield to its mounting bracket using the 2 Phillips ® Head screws and nuts provided, then attach the eye shield assem- bly to the outside wheel guard just above the cut- away. A knurled knob holds the eye shield in place. Figure 1. Figure 2. Knob ...
-
Grizzly G1036 - page 8
G1036 Slow-Speed Grinder -8- A. SAFETY RULES 1. While operating this machine, do not wear jewelry, loose clothing, necklaces or neckties. Long sleeves on shirts should be rolled up or securely buttoned at the cuff. 2. Persons with beards and/or long hair should consider the use of a hat, hair net or similar protective equipment. 3. Always use face/ ...
-
Grizzly G1036 - page 9
-9- G1036 Slow-Speed Grinder Figure 5. Proper sharpening position. Fill the tank reservoir up to approximately 80% full when wet grinding. Do not leave the 10" wheel immersed in water for long periods of time if the grinder is not in use. See Water Reservoir section under the Maintenance heading. The large stone features a fully adjustable too ...
-
Grizzly G1036 - page 10
G1036 Slow-Speed Grinder -10- Figure 6. Oil Feeder check ball. B. OIL FEEDER Apply a light machine oil to the oil feeder after every six hours of operation. Figure 6. A. GENERAL Make a habit of inspecting your Slow-Speed Grinder each time you use it. Check for the fol- lowing conditions and repair or replace when nec- essary. 1. Loose bolts. 2. Wor ...
-
Grizzly G1036 - page 11
-11- G1036 Slow-Speed Grinder in the reservoir once a week to avoid clogging the aluminum oxide wheel. A drain plug at the bottom of the reservoir can be removed to flush out the reservoir and remove sediment. Figure 8. Figure 8. Drain plug on reservoir. Drain C. GEAR BOX The gear box contains the worm-and-pinion gear that transmits power to both t ...
-
Grizzly G1036 - page 12
G1036 Slow-Speed Grinder -12- E. CHANGING STONES The 4 1 / 2 " and 10" stones can both be removed for re-surfacing or replacement. To change the 4 1 / 2 " stone: 1. Remove the eye shield and and the outside wheel guard. 2. Turn the shaft nut counterclockwise while holding the stone. Figure 9. 3. Remove the nut, washer and stone. 4. T ...
-
Grizzly G1036 - page 13
-13- G1036 Slow-Speed Grinder The following pages contain general machine d a t a , parts diagram, parts list and W arranty/Return information for your Model G1036 Slow-Speed Grinder. If you need parts or help in assembling your machine, or if you need operational information, we encourage you to call the appropriate region- al Service Department. ...
-
Grizzly G1036 - page 14
G1036 Slow-Speed Grinder -14- To take advantage of this warranty, contact us by mail or phone and give us all the details. We will then issue you a “Return Number’’, which must be clearly posted on the outside as well as the inside of the carton. We will not accept any item back without this number. Proof of purchase must accompany the mercha ...
Grizzly G1036についてご質問がありますか？
次のフォームを使用してください
見つけた説明書を読んでもGrizzly G1036の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがGrizzly G1036で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。