日本語 dropdown-ico

Panasonic KX-TDE100の取扱説明書

54ページ 0.64 mb
ダウンロード

ページに移動 of 54

Summary
  • Panasonic KX-TDE100 - page 1

    Pure IP-PBX Thank you for purchasing a Panasonic Pure IP-PBX. Please read this manual carefully before using this product and save this manual for future use. KX-TDE100/KX-TDE200: PMMPR Software File V ersion 2.0000 or later KX-TDE600: PGMPR Software File V ersion 2.0000 or later In this manual, the suffix of each model number (e.g., KX-TDE100 NE ) ...

  • Panasonic KX-TDE100 - page 2

    Table of Contents 1 Overview .. ................................................................................................. 3 1.1 Information about IP Telephony Service .. ......................................................................4 1.2 Important Notice for Subscription and Installation .. .......................................... ...

  • Panasonic KX-TDE100 - page 3

    Section 1 Overview This section provides an overview of the V-SIPGW16 card. Programming Manual for Virtual SIP Trunk Card 3 ...

  • Panasonic KX-TDE100 - page 4

    1.1 Information about IP Telephony Service The Virtual 16-Channel SIP Trunk Card ( V-SIPGW16) is a virtual trunk card which is designed to be easily integrated into an Internet Telephony Service provided by an ITSP (Internet Telephony Service Provider). As a major SIP Provider, an ITSP provides its telephony service partly through the conventional ...

  • Panasonic KX-TDE100 - page 5

    • VoIP communication using the V-SIPGW16 card may deteriorate depending on the network conditions. DNS (Domain Name System) A DNS server normally provides the name resolution service for your computer. As domain names are alphabetic, they are easier to remember. The Internet, however, is based on IP addresses. Therefore, every time a domain name ...

  • Panasonic KX-TDE100 - page 6

    LAN WA N Internet STUN STUN STUN STUN Server Server SIP SIP Server Server Fixed IP Address Fixed IP Address SIP SIP Server Server STUN STUN Server SIP Server Fixed IP Address SIP Server PBX with V -SIPGW16 Card ISP/ITSP ISP/ITSP ISP/ITSP ISP/ITSP ISP/ITSP ISP/ITSP Router (NA T enabled) PC IP-PT Switching Hub Note • If an ISP/ITSP uses a device su ...

  • Panasonic KX-TDE100 - page 7

    1.2 Important Notice for Subscription and Installation 1.2.1 Port Requirements Required Ports for Each Channel When configuring a router with NAT enabled, you need to secure a certain number of ports for each SIP and RTP/RTCP channel. For RTP/RTCP, the number of required ports is double the number of activated SIP trunks (Ch). For SIP signalling, t ...

  • Panasonic KX-TDE100 - page 8

    Router Requirements • Port Forwarding: It may be necessary to set the NAT router so that it forwards the incoming packets to the IP address of the V-SIPGW16 card if all of the following conditions are met: – the PBX uses a STUN server; – a V-SIPGW16 card is located under a NAT router; – incoming packets are routed to a SIP Client port or NA ...

  • Panasonic KX-TDE100 - page 9

    1.3 Specifications For details about the RFCs and protocols for the V-SIPGW16 card, refer to the following specifications. Items Specification SIP RFCs RFC3261 (UDP only) RFC3262 (PRACK) RFC3264 (Offer/Answer) RFC3311 (UPDATE) RFC3581 (Symmetric Response Routing/rport) RFC4028 (Session Timer) CODECs G.711 (a-law and µ-law) G.729A Voice Options Ech ...

  • Panasonic KX-TDE100 - page 10

    10 Programming Manual for Virtual SIP Trunk Card 1.3 Specifications ...

  • Panasonic KX-TDE100 - page 11

    Section 2 Preparations for PC Programming This section serves as reference operating instructions when using the Maintenance Console software to programme the V-SIPGW16 card. Programming Manual for Virtual SIP Trunk Card 11 ...

  • Panasonic KX-TDE100 - page 12

    2.1 Maintenance Console Operating Instructions 2.1.1 Installing and Starting the Maintenance Console System programming, diagnosis and administration for the V-SIPGW16 card can be performed with a PC using the Maintenance Console. This section describes how to install and start the Maintenance Console. System Requirements Required Operating System ...

  • Panasonic KX-TDE100 - page 13

    RSA Data Security, Inc. makes no representations concerning either the merchantability of this software or the suitability of this software for any particular purpose. It is provided "as is" without express or implied warranty of any kind. These notices must be retained in any copies of any part of this documentation and/or software. Inst ...

  • Panasonic KX-TDE100 - page 14

    7. When country/area data do not match: a. Click OK to replace the country/area data of the PBX. Replacement may take several minutes to complete. b. Follow the procedure described in Section "3.16.1 Starting the PBX (for KX-TDE100/ KX-TDE200)" or Section "3.18.1 Starting the PBX (for KX-TDE600)" in the Installation Manual and r ...

  • Panasonic KX-TDE100 - page 15

    When not using a DHCP server to obtain a DNS server IP address automatically: a. Select Manual for the DNS Server Address Method setting. b. In the Manual Preferred DNS Server IP Address box, type the IP address of the preferred DNS server. c. In the Manual Alternate DNS Server IP Address box, type the IP address of the alternate DNS server. d. Cli ...

  • Panasonic KX-TDE100 - page 16

    2.2 Installing the V-SIPGW16 Card to the PBX 1. a. Under Configuration , click Slot . b. Move the mouse pointer over the white PBX image at the bottom of the screen for the virtual slots. c. Click Select Shelf . 2. a. Click on the name of the V-SIPGW16 card. An image of the card will be displayed. b. Drag the image of the card to a Trunk slot and r ...

  • Panasonic KX-TDE100 - page 17

    Section 3 Programming the V-SIPGW16 Card This section serves as reference operating instructions when using the Maintenance Console software to programme the V-SIPGW16 card. Programming Manual for Virtual SIP Trunk Card 17 ...

  • Panasonic KX-TDE100 - page 18

    3.1 Programming the V-SIPGW16 Card—Port Property Various settings can be programmed for each virtual SIP gateway port. To change the status of virtual SIP gateway ports, click Command . Accessing Port Properties 1. Under Configuration , click Slot . 2. Move the mouse pointer over the white PBX image at the bottom of the screen for the virtual slo ...

  • Panasonic KX-TDE100 - page 19

    2. Enter information or select from the list for each parameter. 3.1.1 Main Shelf (KX-TDE600 only) Indicates the shelf position (reference only). Value Range Shelf type Slot Indicates the slot position (reference only). Value Range Slot number Port Indicates the port number (reference only). Value Range Port number Connection Indicates the port sta ...

  • Panasonic KX-TDE100 - page 20

    Value Range Max. 20 characters SIP Server Location—Name Specifies the domain name of the SIP proxy server. Note Specify the domain name of the outbound proxy server, if provided by the SIP provider. Value Range Max. 100 characters SIP Server Location—IP Address Specifies the IP address of the SIP proxy server. This setting is compulsory when no ...

  • Panasonic KX-TDE100 - page 21

    Value Range Shelf type Slot Indicates the slot position (reference only). Value Range Slot number Port Indicates the port number (reference only). Value Range Port number Connection Indicates the port status. This column offers two ways to open the screen to select the port command: • Click the desired cell in the column. • Select the desired c ...

  • Panasonic KX-TDE100 - page 22

    3.1.3 Register Shelf (KX-TDE600 only) Indicates the shelf position (reference only). Value Range Shelf type Slot Indicates the slot position (reference only). Value Range Slot number Port Indicates the port number (reference only). Value Range Port number Connection Indicates the port status. This column offers two ways to open the screen to select ...

  • Panasonic KX-TDE100 - page 23

    Un-Register Ability when port INS Specifies whether to unregister the previous registration and send the REGISTER message to the SIP server when the port status is set back to INS. Value Range Disable, Enable Registrar Server—Name Specifies the domain name of the SIP registrar server. Value Range Max. 100 characters Registrar Server—IP Address ...

  • Panasonic KX-TDE100 - page 24

    Connection Indicates the port status. This column offers two ways to open the screen to select the port command: • Click the desired cell in the column. • Select the desired cell in the column, and then click Command . Value Range INS: The port is in service. OUS: The port is out of service. Fault: The port is not communicating with the network ...

  • Panasonic KX-TDE100 - page 25

    Port Indicates the port number (reference only). Value Range Port number Connection Indicates the port status. This column offers two ways to open the screen to select the port command: • Click the desired cell in the column. • Select the desired cell in the column, and then click Command . Value Range INS: The port is in service. OUS: The port ...

  • Panasonic KX-TDE100 - page 26

    3.1.6 Calling Party Shelf (KX-TDE600 only) Indicates the shelf position (reference only). Value Range Shelf type Slot Indicates the slot position (reference only). Value Range Slot number Port Indicates the port number (reference only). Value Range Port number Connection Indicates the port status. This column offers two ways to open the screen to s ...

  • Panasonic KX-TDE100 - page 27

    From Header—SIP-URI Specifies the complete SIP-URI address of the From header. The configuration in From Header—User Part will be invalid if this parameter is set. Value Range Max. 100 characters P-Preferred-Identity Header—User Part Specifies the value to be stored in the username part of the SIP-URI of the P-Preferred-Identity header. Value ...

  • Panasonic KX-TDE100 - page 28

    Value Range Shelf type Slot Indicates the slot position (reference only). Value Range Slot number Port Indicates the port number (reference only). Value Range Port number Connection Indicates the port status. This column offers two ways to open the screen to select the port command: • Click the desired cell in the column. • Select the desired c ...

  • Panasonic KX-TDE100 - page 29

    Value Range Shelf type Slot Indicates the slot position (reference only). Value Range Slot number Port Indicates the port number (reference only). Value Range Port number Connection Indicates the port status. This column offers two ways to open the screen to select the port command: • Click the desired cell in the column. • Select the desired c ...

  • Panasonic KX-TDE100 - page 30

    Packet Sampling Time (G.729A) Specifies the time interval between measurements (samples) of sound data during a conversation. The smaller this number, the higher the quality of the transmitted sound. Value Range 10 ms, 20 ms, 30 ms, 40 ms, 50 ms, 60 ms Voice Activity Detection for G.711 Enables the use of the Voice Activity Detection feature for th ...

  • Panasonic KX-TDE100 - page 31

    Note Manual programming is required if DTMF is set to Outband (RFC2833) . Value Range 96–127 3.1.9 RTP/RTCP Shelf (KX-TDE600 only) Indicates the shelf position (reference only). Value Range Shelf type Slot Indicates the slot position (reference only). Value Range Slot number Port Indicates the port number (reference only). Value Range Port number ...

  • Panasonic KX-TDE100 - page 32

    Value Range 0–7 RTP QoS-ToS Type Specifies the ToS type in the ToS field. Value Range Normal, Monetary Cost, Reliability , Throughput, Delay RTP QoS-DSCP Specifies the value in the ToS field by a DSCP for DiffServ. Value Range 0–63 RTP QoS-HEX Specifies the value in the ToS field by a hexadecimal number. Value Range 00–FF RTCP Packet Sending ...

  • Panasonic KX-TDE100 - page 33

    Value Range Slot number Port Indicates the port number (reference only). Value Range Port number Connection Indicates the port status. This column offers two ways to open the screen to select the port command: • Click the desired cell in the column. • Select the desired cell in the column, and then click Command . Value Range INS: The port is i ...

  • Panasonic KX-TDE100 - page 34

    T.38 FAX Rate Management Method Specifies the rate management method when using the T.38 protocol. Value Range Transferred TCF, Local TCF 3.1.11 T.38 Option Shelf (KX-TDE600 only) Indicates the shelf position (reference only). Value Range Shelf type Slot Indicates the slot position (reference only). Value Range Slot number Port Indicates the port n ...

  • Panasonic KX-TDE100 - page 35

    Value Range 0–7 T.38 FAX QoS-ToS Type Specifies the ToS type in the ToS field when using the T.38 protocol. Value Range Normal, Monetary Cost, Reliability , Throughput, Delay T.38 FAX QoS-DSCP Specifies the value in the ToS field by a DSCP for DiffServ when using the T.38 protocol. This setting is compulsory when DSCP is selected in T.38 FAX QoS ...

  • Panasonic KX-TDE100 - page 36

    Connection Indicates the port status. This column offers two ways to open the screen to select the port command: • Click the desired cell in the column. • Select the desired cell in the column, and then click Command . Value Range INS: The port is in service. OUS: The port is out of service. Fault: The port is not communicating with the network ...

  • Panasonic KX-TDE100 - page 37

    Value Range Shelf type Slot Indicates the slot position (reference only). Value Range Slot number Port Indicates the port number (reference only). Value Range Port number Connection Indicates the port status. This column offers two ways to open the screen to select the port command: • Click the desired cell in the column. • Select the desired c ...

  • Panasonic KX-TDE100 - page 38

    Value Range Yes, No 38 Programming Manual for Virtual SIP Trunk Card 3.1.13 Supplementary Service ...

  • Panasonic KX-TDE100 - page 39

    3.2 Programming the V-SIPGW16 Card—Card Property 3.2.1 Card Property The properties of the V-SIPGW card can be specified. To programme the parameters, click Common Settings , and set the desired value. Accessing Card Properties 1. Under Configuration , click Slot . 2. Move the mouse pointer over the white PBX image at the bottom of the screen for ...

  • Panasonic KX-TDE100 - page 40

    Value Range 1.0.0.0–223.255.255.255 Manual Preferred DNS Server IP Address Specifies the IP address of the preferred DNS server manually. This setting is compulsory if a DNS server IP address is not assigned automatically. Value Range 1.0.0.0–223.255.255.255 Manual Alternate DNS Server IP Address Specifies the IP address of the alternate DNS se ...

  • Panasonic KX-TDE100 - page 41

    DNS SRV Record Resolve Ability Specifies whether to request that the DNS server translates domain names into IP addresses using the DNS SRV record. Value Range Disable, Enable Programming Manual for Virtual SIP Trunk Card 41 3.2.1 Card Property ...

  • Panasonic KX-TDE100 - page 42

    3.3 Programming the V-SIPGW16 Card—Shelf Property Common settings for all of the V-SIPGW cards installed in the IPCMPR (for KX-TDE100/KX-TDE200)/ IPCEMPR (for KX-TDE600) Virtual Shelf can be programmed. Accessing Shelf Properties 1. Under Configuration , click Slot . 2. Move the mouse pointer over the white PBX image at the bottom of the screen f ...

  • Panasonic KX-TDE100 - page 43

    NAT - Voice (RTP) UDP Port No. Specifies the starting port number of the dynamic ports used for NAT Traversal. Value Range 2–65000 (even number only) NAT - Keep Alive Packet Sending Ability Specifies whether to send Keep Alive packets in order to maintain the NAT binding information. This setting may be compulsory depending on the network conditi ...

  • Panasonic KX-TDE100 - page 44

    Value Range 1–65535 STUN External Address Detection Retry Counter Specifies the number of times that a query is retried when no response is received from the STUN server. Value Range 0–8 STUN Resending Interval Specifies the length of time until a query is retried when no response is received from the STUN server. Value Range 0–1600 ms SIP Ca ...

  • Panasonic KX-TDE100 - page 45

    3.3.2 Timer SIP T1 Specifies the retransmission interval time for INVITE requests and responses. Value Range 5–255 ´ 100 ms SIP T2 Specifies the retransmission interval time for INVITE responses and non-INVITE requests. Value Range 40–255 ´ 100 ms Programming Manual for Virtual SIP Trunk Card 45 3.3.2 Timer ...

  • Panasonic KX-TDE100 - page 46

    46 Programming Manual for Virtual SIP Trunk Card 3.3.2 Timer ...

  • Panasonic KX-TDE100 - page 47

    Section 4 Maintenance This section serves as reference operating instructions for data management of the V-SIPGW16 card using the Maintenance Console software. Programming Manual for Virtual SIP Trunk Card 47 ...

  • Panasonic KX-TDE100 - page 48

    4.1 Configuration Management 4.1.1 Importing/Exporting V-SIPGW16 Provider Profiles Provider profiles for the V-SIPGW16 card can be exported or imported (if updated provider profiles are available), using the Import/Export tool. Follow the steps below to import or export the provider profiles: Note To access the following menu options, you must be l ...

  • Panasonic KX-TDE100 - page 49

    4.1.2 V-SIPGW16 Protocol Trace The trace data of protocol activity can be collected from the V-SIPGW16 card and saved to the PC, using the utility, V-SIPGW16 Protocol Trace . This option requires that the target V-SIPGW16 card be set to INS status. Follow the steps below to trace and file V-SIPGW16 card protocol activity: Note To access the followi ...

  • Panasonic KX-TDE100 - page 50

    50 Programming Manual for Virtual SIP Trunk Card 4.1.2 V-SIPGW16 Protocol Trace ...

  • Panasonic KX-TDE100 - page 51

    Index Programming Manual for Virtual SIP Trunk Card 51 ...

  • Panasonic KX-TDE100 - page 52

    A Accessing Card Properties 39 Accessing Port Properties 18 Accessing Shelf Properties 42 Automatic Programming, Port Property 18 B Bandwidth Requirements 8 C Card Property, Icon Description 39 Card Property, Programming 39 Configuration Management 48 D DHCP Server 14 DNS (Domain Name System) 5 DNS Server 5 F Firewall Requirements 7 Fixed IP Addres ...

  • Panasonic KX-TDE100 - page 53

    Programming Manual for Virtual SIP Trunk Card 53 Notes ...

  • Panasonic KX-TDE100 - page 54

    Panasonic Communications Co., Ltd. 1-62, 4-chome, Minoshima, Hakata-ku, Fukuoka 812-8531, Japan PSQX5028ZA Copyright: This material is copyrighted by Panasonic Communications Co., Ltd., and may be reproduced for internal use only. All other reproduction, in whole or in part, is prohibited without the written consent of Panasonic Communications Co., ...

メーカー Panasonic カテゴリー Whiteboard Accessories

Panasonic KX-TDE100のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- KX-TDE100の取扱説明書
- Panasonicの製品カード
- パンフレット
- またはPanasonic KX-TDE100の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Panasonic KX-TDE100の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Panasonic KX-TDE100の取り付け説明書、サービスマニュアル、簡易説明書、またはPanasonic KX-TDE100のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Panasonic KX-TDE100の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Panasonic KX-TDE100デバイスの取扱説明書はどのようなものですか？
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがPanasonic KX-TDE100を使用するのを助ける技術的文書のことです。説明書は通常、全てのPanasonic KX-TDE100ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Panasonicの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Panasonic KX-TDE100の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははPanasonic KX-TDE100の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Panasonic KX-TDE100に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Panasonic KX-TDE100デバイスの基本機能を使うにあたってのヒント。 Panasonic KX-TDE100のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Panasonic KX-TDE100に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるPanasonic KX-TDE100のメーカー/サービスへの連絡先に関する情報。

Panasonic KX-TDE100についてご質問がありますか？

次のフォームを使用してください

見つけた説明書を読んでもPanasonic KX-TDE100の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがPanasonic KX-TDE100で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

Captcha
新しい画像

コメント (0)