Henny Penny 581の取扱説明書

12ページ 0.68 mb
ダウンロード

ページに移動 of 12

Summary
  • Henny Penny 581 - page 1

    This section provides troubleshooting information in the form of an easy to read table. If a problem occurs during the first operation of a new fryer, recheck the installation per the Installation Section of this manual. Before troubleshooting, always recheck the operation pro- cedures per Section 3 of this manual. To isolate a malfunction, proceed ...

  • Henny Penny 581 - page 2

    Product Color Not Correct: A. Too Dark B. Too Light C. Product Greasy Temperature too high. Shortening too old. Shortening too dark. Breading product too far in advance. Wrong cook button pushed. Temperature too low. Fryer incorrect preheat. Slow fryer heat-up/ recovery. Wrong cook button pushed. Shortening old. Temperature too low. Wrong cook butt ...

  • Henny Penny 581 - page 3

    B. Too Light C. Product Greasy D. Spotted Product Temperature too low. Fryer incorrect preheat. Slow fryer heat-up/ recovery. Wrong cook button pushed. 0 Shortening old. Temperature too low. 0 Cookpot overloaded. Product not removed from cookpot immediately after end of cycle. Improper separation of the product. Breading not uniform on the product. ...

  • Henny Penny 581 - page 4

    E. Dryness of Product Product Flavor (Taste): A. Salty Taste urned Taste 6. Bland Taste Moisture loss prior to cooking. Overcooking the product. Low operating pressure. Wrong cook button pushed. Breading mixture is too salty. Incorrect choice of breading. Burned shortening flavor. Cookpot not properly cleaned. aw product not fresh. Breading mixture ...

  • Henny Penny 581 - page 5

    D. Rancid Taste Replace shortening, and follow recommended care and use of shortening. Replace shortening. Use compatible products, and follow recommended care and use of shortening. General: A. Meat Separation From Bone B. Bone Color Not Proper 6. Breading Falh Off D. Product Sticking Together Shortening too old. Non compatible products cooked wit ...

  • Henny Penny 581 - page 6

    With switch in POWER position, the fryer is com- pletely inoperative (NO POWER) Pressure will not exhaust at end of cooking cycle. Operating pressure too high Open circuit. Exhaust line from solenoid valve to condensation tank clogged. Solenoid valve clogged. Dead weight clogged. Check to see that unit is plugged in. Check the breaker or fuse at su ...

  • Henny Penny 581 - page 7

    Henny Penny Model 581 Problem Cause Correction LID/PRESSURE SE CTION (Continued) • Exhaust line to stack clogged • Clean exhaust line to stack. DO NOT OPERATE UNIT IF HI GH PRESSURE CONDITIONS EX IST, SEVERE INJURIES AND BURNS WILL RESULT. Place th e Power/P ump switch in the “OFF ” position immediately . Release the pressure by allowing un ...

  • Henny Penny 581 - page 8

    Henny Penny Model 581 Problem Cause Correction LID/PRESSURE SE CTION (Continu ed) • Safet y relief valve le aking. • Check and replac e if necessar y per maintenance section on the re lief valve. • Pressure pad broken or crushed. • Replace pressure p ads. Lid won’t move • Cable on Counterweight • Put cable on Counterweight up or down ...

  • Henny Penny 581 - page 9

    Heating of shortening too slow (Electric Model) Shortening overheating (Electric Model) Foaming or boil- ing o,ver of shortening Low or improper voltage. Weak or burnt out element(s). Points in contactor bad. Wire(s) loose. Burnt or charred wire connection. Check shortening temperature. Check contactor for not opening. Faulty PC Board. Faulty probe ...

  • Henny Penny 581 - page 10

    Shortening will not drain from cookpot Shortening leaking through drain valve. Cold zone full of cracklings. Improper rinsing after cleaning the fryer. Too much stirring. Drain valve clogged with crumbs. Drain valve will not open by pulling the knob. Obstruction in drain. Faulty drain valve. Filter shortening. Clean and neutralize the cookpot. Rins ...

  • Henny Penny 581 - page 11

    The following guide requires voltage to be present when troubleshooting the control. When the guide refers to connecting pins on the power connection, unplug the power connector from the board and refer to the attached illustration. These are numbered 1 through 9. Using a strand of #16 gauge wire, connect the pins as numbered in the troubleshooting ...

  • Henny Penny 581 - page 12

    Error message E-5 display reads HI. Error message E-6. Error message E-10. Error message E-41. Read display temperature - if display temperature reads HI, unplug power connector from control board. If secondary contactor stays engaged, change contactor - if secondary contactor disengages, change control board. If shortening temperature reads normal ...

メーカー Henny Penny カテゴリー Electric Pressure Cooker

Henny Penny 581のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 581の取扱説明書
- Henny Pennyの製品カード
- パンフレット
- またはHenny Penny 581の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Henny Penny 581の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Henny Penny 581の取り付け説明書、サービスマニュアル、簡易説明書、またはHenny Penny 581のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Henny Penny 581の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Henny Penny 581デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがHenny Penny 581を使用するのを助ける技術的文書のことです。説明書は通常、全てのHenny Penny 581ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Henny Pennyの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Henny Penny 581の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははHenny Penny 581の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Henny Penny 581に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Henny Penny 581デバイスの基本機能を使うにあたってのヒント。 Henny Penny 581のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Henny Penny 581に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるHenny Penny 581のメーカー/サービスへの連絡先に関する情報。

Henny Penny 581についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもHenny Penny 581の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがHenny Penny 581で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)